// SPDX-License-Identifier: GPL-2.0 /* Copyright(c) 1999 - 2018 Intel Corporation. */ #include "e1000.h" #include <linux/ethtool.h> static s32 e1000_wait_autoneg(struct e1000_hw *hw); static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data, bool read, bool page_set); static u32 e1000_get_phy_addr_for_hv_page(u32 page); static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset, u16 *data, bool read); /* Cable length tables */ static const u16 e1000_m88_cable_length_table[] = …; #define M88E1000_CABLE_LENGTH_TABLE_SIZE … static const u16 e1000_igp_2_cable_length_table[] = …; #define IGP02E1000_CABLE_LENGTH_TABLE_SIZE … /** * e1000e_check_reset_block_generic - Check if PHY reset is blocked * @hw: pointer to the HW structure * * Read the PHY management control register and check whether a PHY reset * is blocked. If a reset is not blocked return 0, otherwise * return E1000_BLK_PHY_RESET (12). **/ s32 e1000e_check_reset_block_generic(struct e1000_hw *hw) { … } /** * e1000e_get_phy_id - Retrieve the PHY ID and revision * @hw: pointer to the HW structure * * Reads the PHY registers and stores the PHY ID and possibly the PHY * revision in the hardware structure. **/ s32 e1000e_get_phy_id(struct e1000_hw *hw) { … } /** * e1000e_phy_reset_dsp - Reset PHY DSP * @hw: pointer to the HW structure * * Reset the digital signal processor. **/ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw) { … } void e1000e_disable_phy_retry(struct e1000_hw *hw) { … } void e1000e_enable_phy_retry(struct e1000_hw *hw) { … } /** * e1000e_read_phy_reg_mdic - Read MDI control register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the MDI control register in the PHY at offset and stores the * information read to data. **/ s32 e1000e_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_write_phy_reg_mdic - Write MDI control register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write to register at offset * * Writes data to MDI control register in the PHY at offset. **/ s32 e1000e_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000e_read_phy_reg_m88 - Read m88 PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore, if necessary, then reads the PHY register at offset * and storing the retrieved information in data. Release any acquired * semaphores before exiting. **/ s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_write_phy_reg_m88 - Write m88 PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore, if necessary, then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_set_page_igp - Set page as on IGP-like PHY(s) * @hw: pointer to the HW structure * @page: page to set (shifted left when necessary) * * Sets PHY page required for PHY register access. Assumes semaphore is * already acquired. Note, this function sets phy.addr to 1 so the caller * must set it appropriately (if necessary) after this function returns. **/ s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page) { … } /** * __e1000e_read_phy_reg_igp - Read igp PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * @locked: semaphore has already been acquired or not * * Acquires semaphore, if necessary, then reads the PHY register at offset * and stores the retrieved information in data. Release any acquired * semaphores before exiting. **/ static s32 __e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data, bool locked) { … } /** * e1000e_read_phy_reg_igp - Read igp PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore then reads the PHY register at offset and stores the * retrieved information in data. * Release the acquired semaphore before exiting. **/ s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_read_phy_reg_igp_locked - Read igp PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the PHY register at offset and stores the retrieved information * in data. Assumes semaphore already acquired. **/ s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * __e1000e_write_phy_reg_igp - Write igp PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * @locked: semaphore has already been acquired or not * * Acquires semaphore, if necessary, then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ static s32 __e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data, bool locked) { … } /** * e1000e_write_phy_reg_igp - Write igp PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ s32 e1000e_write_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000e_write_phy_reg_igp_locked - Write igp PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Writes the data to PHY register at the offset. * Assumes semaphore already acquired. **/ s32 e1000e_write_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * __e1000_read_kmrn_reg - Read kumeran register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * @locked: semaphore has already been acquired or not * * Acquires semaphore, if necessary. Then reads the PHY register at offset * using the kumeran interface. The information retrieved is stored in data. * Release any acquired semaphores before exiting. **/ static s32 __e1000_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data, bool locked) { … } /** * e1000e_read_kmrn_reg - Read kumeran register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore then reads the PHY register at offset using the * kumeran interface. The information retrieved is stored in data. * Release the acquired semaphore before exiting. **/ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_read_kmrn_reg_locked - Read kumeran register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the PHY register at offset using the kumeran interface. The * information retrieved is stored in data. * Assumes semaphore already acquired. **/ s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * __e1000_write_kmrn_reg - Write kumeran register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * @locked: semaphore has already been acquired or not * * Acquires semaphore, if necessary. Then write the data to PHY register * at the offset using the kumeran interface. Release any acquired semaphores * before exiting. **/ static s32 __e1000_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data, bool locked) { … } /** * e1000e_write_kmrn_reg - Write kumeran register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore then writes the data to the PHY register at the offset * using the kumeran interface. Release the acquired semaphore before exiting. **/ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000e_write_kmrn_reg_locked - Write kumeran register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Write the data to PHY register at the offset using the kumeran interface. * Assumes semaphore already acquired. **/ s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_set_master_slave_mode - Setup PHY for Master/slave mode * @hw: pointer to the HW structure * * Sets up Master/slave mode **/ static s32 e1000_set_master_slave_mode(struct e1000_hw *hw) { … } /** * e1000_copper_link_setup_82577 - Setup 82577 PHY for copper link * @hw: pointer to the HW structure * * Sets up Carrier-sense on Transmit and downshift values. **/ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw) { … } /** * e1000e_copper_link_setup_m88 - Setup m88 PHY's for copper link * @hw: pointer to the HW structure * * Sets up MDI/MDI-X and polarity for m88 PHY's. If necessary, transmit clock * and downshift values are set also. **/ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw) { … } /** * e1000e_copper_link_setup_igp - Setup igp PHY's for copper link * @hw: pointer to the HW structure * * Sets up LPLU, MDI/MDI-X, polarity, Smartspeed and Master/Slave config for * igp PHY's. **/ s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw) { … } /** * e1000_phy_setup_autoneg - Configure PHY for auto-negotiation * @hw: pointer to the HW structure * * Reads the MII auto-neg advertisement register and/or the 1000T control * register and if the PHY is already setup for auto-negotiation, then * return successful. Otherwise, setup advertisement and flow control to * the appropriate values for the wanted auto-negotiation. **/ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) { … } /** * e1000_copper_link_autoneg - Setup/Enable autoneg for copper link * @hw: pointer to the HW structure * * Performs initial bounds checking on autoneg advertisement parameter, then * configure to advertise the full capability. Setup the PHY to autoneg * and restart the negotiation process between the link partner. If * autoneg_wait_to_complete, then wait for autoneg to complete before exiting. **/ static s32 e1000_copper_link_autoneg(struct e1000_hw *hw) { … } /** * e1000e_setup_copper_link - Configure copper link settings * @hw: pointer to the HW structure * * Calls the appropriate function to configure the link for auto-neg or forced * speed and duplex. Then we check for link, once link is established calls * to configure collision distance and flow control are called. If link is * not established, we return -E1000_ERR_PHY (-2). **/ s32 e1000e_setup_copper_link(struct e1000_hw *hw) { … } /** * e1000e_phy_force_speed_duplex_igp - Force speed/duplex for igp PHY * @hw: pointer to the HW structure * * Calls the PHY setup function to force speed and duplex. Clears the * auto-crossover to force MDI manually. Waits for link and returns * successful if link up is successful, else -E1000_ERR_PHY (-2). **/ s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw) { … } /** * e1000e_phy_force_speed_duplex_m88 - Force speed/duplex for m88 PHY * @hw: pointer to the HW structure * * Calls the PHY setup function to force speed and duplex. Clears the * auto-crossover to force MDI manually. Resets the PHY to commit the * changes. If time expires while waiting for link up, we reset the DSP. * After reset, TX_CLK and CRS on Tx must be set. Return successful upon * successful completion, else return corresponding error code. **/ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw) { … } /** * e1000_phy_force_speed_duplex_ife - Force PHY speed & duplex * @hw: pointer to the HW structure * * Forces the speed and duplex settings of the PHY. * This is a function pointer entry point only called by * PHY setup routines. **/ s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw) { … } /** * e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex * @hw: pointer to the HW structure * @phy_ctrl: pointer to current value of MII_BMCR * * Forces speed and duplex on the PHY by doing the following: disable flow * control, force speed/duplex on the MAC, disable auto speed detection, * disable auto-negotiation, configure duplex, configure speed, configure * the collision distance, write configuration to CTRL register. The * caller must write to the MII_BMCR register for these settings to * take affect. **/ void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl) { … } /** * e1000e_set_d3_lplu_state - Sets low power link up state for D3 * @hw: pointer to the HW structure * @active: boolean used to enable/disable lplu * * Success returns 0, Failure returns 1 * * The low power link up (lplu) state is set to the power management level D3 * and SmartSpeed is disabled when active is true, else clear lplu for D3 * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU * is used during Dx states where the power conservation is most important. * During driver activity, SmartSpeed should be enabled so performance is * maintained. **/ s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active) { … } /** * e1000e_check_downshift - Checks whether a downshift in speed occurred * @hw: pointer to the HW structure * * Success returns 0, Failure returns 1 * * A downshift is detected by querying the PHY link health. **/ s32 e1000e_check_downshift(struct e1000_hw *hw) { … } /** * e1000_check_polarity_m88 - Checks the polarity. * @hw: pointer to the HW structure * * Success returns 0, Failure returns -E1000_ERR_PHY (-2) * * Polarity is determined based on the PHY specific status register. **/ s32 e1000_check_polarity_m88(struct e1000_hw *hw) { … } /** * e1000_check_polarity_igp - Checks the polarity. * @hw: pointer to the HW structure * * Success returns 0, Failure returns -E1000_ERR_PHY (-2) * * Polarity is determined based on the PHY port status register, and the * current speed (since there is no polarity at 100Mbps). **/ s32 e1000_check_polarity_igp(struct e1000_hw *hw) { … } /** * e1000_check_polarity_ife - Check cable polarity for IFE PHY * @hw: pointer to the HW structure * * Polarity is determined on the polarity reversal feature being enabled. **/ s32 e1000_check_polarity_ife(struct e1000_hw *hw) { … } /** * e1000_wait_autoneg - Wait for auto-neg completion * @hw: pointer to the HW structure * * Waits for auto-negotiation to complete or for the auto-negotiation time * limit to expire, which ever happens first. **/ static s32 e1000_wait_autoneg(struct e1000_hw *hw) { … } /** * e1000e_phy_has_link_generic - Polls PHY for link * @hw: pointer to the HW structure * @iterations: number of times to poll for link * @usec_interval: delay between polling attempts * @success: pointer to whether polling was successful or not * * Polls the PHY status register for link, 'iterations' number of times. **/ s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations, u32 usec_interval, bool *success) { … } /** * e1000e_get_cable_length_m88 - Determine cable length for m88 PHY * @hw: pointer to the HW structure * * Reads the PHY specific status register to retrieve the cable length * information. The cable length is determined by averaging the minimum and * maximum values to get the "average" cable length. The m88 PHY has four * possible cable length values, which are: * Register Value Cable Length * 0 < 50 meters * 1 50 - 80 meters * 2 80 - 110 meters * 3 110 - 140 meters * 4 > 140 meters **/ s32 e1000e_get_cable_length_m88(struct e1000_hw *hw) { … } /** * e1000e_get_cable_length_igp_2 - Determine cable length for igp2 PHY * @hw: pointer to the HW structure * * The automatic gain control (agc) normalizes the amplitude of the * received signal, adjusting for the attenuation produced by the * cable. By reading the AGC registers, which represent the * combination of coarse and fine gain value, the value can be put * into a lookup table to obtain the approximate cable length * for each channel. **/ s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw) { … } /** * e1000e_get_phy_info_m88 - Retrieve PHY information * @hw: pointer to the HW structure * * Valid for only copper links. Read the PHY status register (sticky read) * to verify that link is up. Read the PHY special control register to * determine the polarity and 10base-T extended distance. Read the PHY * special status register to determine MDI/MDIx and current speed. If * speed is 1000, then determine cable length, local and remote receiver. **/ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw) { … } /** * e1000e_get_phy_info_igp - Retrieve igp PHY information * @hw: pointer to the HW structure * * Read PHY status to determine if link is up. If link is up, then * set/determine 10base-T extended distance and polarity correction. Read * PHY port status to determine MDI/MDIx and speed. Based on the speed, * determine on the cable length, local and remote receiver. **/ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw) { … } /** * e1000_get_phy_info_ife - Retrieves various IFE PHY states * @hw: pointer to the HW structure * * Populates "phy" structure with various feature states. **/ s32 e1000_get_phy_info_ife(struct e1000_hw *hw) { … } /** * e1000e_phy_sw_reset - PHY software reset * @hw: pointer to the HW structure * * Does a software reset of the PHY by reading the PHY control register and * setting/write the control register reset bit to the PHY. **/ s32 e1000e_phy_sw_reset(struct e1000_hw *hw) { … } /** * e1000e_phy_hw_reset_generic - PHY hardware reset * @hw: pointer to the HW structure * * Verify the reset block is not blocking us from resetting. Acquire * semaphore (if necessary) and read/set/write the device control reset * bit in the PHY. Wait the appropriate delay time for the device to * reset and release the semaphore (if necessary). **/ s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw) { … } /** * e1000e_get_cfg_done_generic - Generic configuration done * @hw: pointer to the HW structure * * Generic function to wait 10 milli-seconds for configuration to complete * and return success. **/ s32 e1000e_get_cfg_done_generic(struct e1000_hw __always_unused *hw) { … } /** * e1000e_phy_init_script_igp3 - Inits the IGP3 PHY * @hw: pointer to the HW structure * * Initializes a Intel Gigabit PHY3 when an EEPROM is not present. **/ s32 e1000e_phy_init_script_igp3(struct e1000_hw *hw) { … } /** * e1000e_get_phy_type_from_id - Get PHY type from id * @phy_id: phy_id read from the phy * * Returns the phy type from the id. **/ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id) { … } /** * e1000e_determine_phy_address - Determines PHY address. * @hw: pointer to the HW structure * * This uses a trial and error method to loop through possible PHY * addresses. It tests each by reading the PHY ID registers and * checking for a match. **/ s32 e1000e_determine_phy_address(struct e1000_hw *hw) { … } /** * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address * @page: page to access * @reg: register to check * * Returns the phy address for the page requested. **/ static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg) { … } /** * e1000e_write_phy_reg_bm - Write BM PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore, if necessary, then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000e_read_phy_reg_bm - Read BM PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore, if necessary, then reads the PHY register at offset * and storing the retrieved information in data. Release any acquired * semaphores before exiting. **/ s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_read_phy_reg_bm2 - Read BM PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore, if necessary, then reads the PHY register at offset * and storing the retrieved information in data. Release any acquired * semaphores before exiting. **/ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000e_write_phy_reg_bm2 - Write BM PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore, if necessary, then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_enable_phy_wakeup_reg_access_bm - enable access to BM wakeup registers * @hw: pointer to the HW structure * @phy_reg: pointer to store original contents of BM_WUC_ENABLE_REG * * Assumes semaphore already acquired and phy_reg points to a valid memory * address to store contents of the BM_WUC_ENABLE_REG register. **/ s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg) { … } /** * e1000_disable_phy_wakeup_reg_access_bm - disable access to BM wakeup regs * @hw: pointer to the HW structure * @phy_reg: pointer to original contents of BM_WUC_ENABLE_REG * * Restore BM_WUC_ENABLE_REG to its original value. * * Assumes semaphore already acquired and *phy_reg is the contents of the * BM_WUC_ENABLE_REG before register(s) on BM_WUC_PAGE were accessed by * caller. **/ s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg) { … } /** * e1000_access_phy_wakeup_reg_bm - Read/write BM PHY wakeup register * @hw: pointer to the HW structure * @offset: register offset to be read or written * @data: pointer to the data to read or write * @read: determines if operation is read or write * @page_set: BM_WUC_PAGE already set and access enabled * * Read the PHY register at offset and store the retrieved information in * data, or write data to PHY register at offset. Note the procedure to * access the PHY wakeup registers is different than reading the other PHY * registers. It works as such: * 1) Set 769.17.2 (page 769, register 17, bit 2) = 1 * 2) Set page to 800 for host (801 if we were manageability) * 3) Write the address using the address opcode (0x11) * 4) Read or write the data using the data opcode (0x12) * 5) Restore 769.17.2 to its original value * * Steps 1 and 2 are done by e1000_enable_phy_wakeup_reg_access_bm() and * step 5 is done by e1000_disable_phy_wakeup_reg_access_bm(). * * Assumes semaphore is already acquired. When page_set==true, assumes * the PHY page is set to BM_WUC_PAGE (i.e. a function in the call stack * is responsible for calls to e1000_[enable|disable]_phy_wakeup_reg_bm()). **/ static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data, bool read, bool page_set) { … } /** * e1000_power_up_phy_copper - Restore copper link in case of PHY power down * @hw: pointer to the HW structure * * In the case of a PHY power down to save power, or to turn off link during a * driver unload, or wake on lan is not enabled, restore the link to previous * settings. **/ void e1000_power_up_phy_copper(struct e1000_hw *hw) { … } /** * e1000_power_down_phy_copper - Restore copper link in case of PHY power down * @hw: pointer to the HW structure * * In the case of a PHY power down to save power, or to turn off link during a * driver unload, or wake on lan is not enabled, restore the link to previous * settings. **/ void e1000_power_down_phy_copper(struct e1000_hw *hw) { … } /** * __e1000_read_phy_reg_hv - Read HV PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * @locked: semaphore has already been acquired or not * @page_set: BM_WUC_PAGE already set and access enabled * * Acquires semaphore, if necessary, then reads the PHY register at offset * and stores the retrieved information in data. Release any acquired * semaphore before exiting. **/ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data, bool locked, bool page_set) { … } /** * e1000_read_phy_reg_hv - Read HV PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Acquires semaphore then reads the PHY register at offset and stores * the retrieved information in data. Release the acquired semaphore * before exiting. **/ s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000_read_phy_reg_hv_locked - Read HV PHY register * @hw: pointer to the HW structure * @offset: register offset to be read * @data: pointer to the read data * * Reads the PHY register at offset and stores the retrieved information * in data. Assumes semaphore already acquired. **/ s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * e1000_read_phy_reg_page_hv - Read HV PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Reads the PHY register at offset and stores the retrieved information * in data. Assumes semaphore already acquired and page already set. **/ s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 *data) { … } /** * __e1000_write_phy_reg_hv - Write HV PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * @locked: semaphore has already been acquired or not * @page_set: BM_WUC_PAGE already set and access enabled * * Acquires semaphore, if necessary, then writes the data to PHY register * at the offset. Release any acquired semaphores before exiting. **/ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data, bool locked, bool page_set) { … } /** * e1000_write_phy_reg_hv - Write HV PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Acquires semaphore then writes the data to PHY register at the offset. * Release the acquired semaphores before exiting. **/ s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_write_phy_reg_hv_locked - Write HV PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Writes the data to PHY register at the offset. Assumes semaphore * already acquired. **/ s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_write_phy_reg_page_hv - Write HV PHY register * @hw: pointer to the HW structure * @offset: register offset to write to * @data: data to write at register offset * * Writes the data to PHY register at the offset. Assumes semaphore * already acquired and page already set. **/ s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 data) { … } /** * e1000_get_phy_addr_for_hv_page - Get PHY address based on page * @page: page to be accessed **/ static u32 e1000_get_phy_addr_for_hv_page(u32 page) { … } /** * e1000_access_phy_debug_regs_hv - Read HV PHY vendor specific high registers * @hw: pointer to the HW structure * @offset: register offset to be read or written * @data: pointer to the data to be read or written * @read: determines if operation is read or write * * Reads the PHY register at offset and stores the retrieved information * in data. Assumes semaphore already acquired. Note that the procedure * to access these regs uses the address port and data port to read/write. * These accesses done with PHY address 2 and without using pages. **/ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset, u16 *data, bool read) { … } /** * e1000_link_stall_workaround_hv - Si workaround * @hw: pointer to the HW structure * * This function works around a Si bug where the link partner can get * a link up indication before the PHY does. If small packets are sent * by the link partner they can be placed in the packet buffer without * being properly accounted for by the PHY and will stall preventing * further packets from being received. The workaround is to clear the * packet buffer after the PHY detects link up. **/ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw) { … } /** * e1000_check_polarity_82577 - Checks the polarity. * @hw: pointer to the HW structure * * Success returns 0, Failure returns -E1000_ERR_PHY (-2) * * Polarity is determined based on the PHY specific status register. **/ s32 e1000_check_polarity_82577(struct e1000_hw *hw) { … } /** * e1000_phy_force_speed_duplex_82577 - Force speed/duplex for I82577 PHY * @hw: pointer to the HW structure * * Calls the PHY setup function to force speed and duplex. **/ s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw) { … } /** * e1000_get_phy_info_82577 - Retrieve I82577 PHY information * @hw: pointer to the HW structure * * Read PHY status to determine if link is up. If link is up, then * set/determine 10base-T extended distance and polarity correction. Read * PHY port status to determine MDI/MDIx and speed. Based on the speed, * determine on the cable length, local and remote receiver. **/ s32 e1000_get_phy_info_82577(struct e1000_hw *hw) { … } /** * e1000_get_cable_length_82577 - Determine cable length for 82577 PHY * @hw: pointer to the HW structure * * Reads the diagnostic status register and verifies result is valid before * placing it in the phy_cable_length field. **/ s32 e1000_get_cable_length_82577(struct e1000_hw *hw) { … }
Codebase Browser
linux