/*
* BSD LICENSE
*
* Copyright(c) 2015 Broadcom Corporation. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Broadcom Corporation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clock/bcm-nsp.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "brcm,nsp";
model = "Broadcom Northstar Plus SoC";
interrupt-parent = <&gic>;
aliases {
serial0 = &uart0;
serial1 = &uart1;
ethernet0 = &amac0;
ethernet1 = &amac1;
ethernet2 = &amac2;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a9";
next-level-cache = <&L2>;
reg = <0x0>;
};
cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
next-level-cache = <&L2>;
enable-method = "brcm,bcm-nsp-smp";
secondary-boot-reg = <0xffff0fec>;
reg = <0x1>;
};
};
pmu {
compatible = "arm,cortex-a9-pmu";
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>, <&cpu1>;
};
mpcore-bus@19000000 {
compatible = "simple-bus";
ranges = <0x00000000 0x19000000 0x00023000>;
#address-cells = <1>;
#size-cells = <1>;
a9pll: arm_clk@0 {
#clock-cells = <0>;
compatible = "brcm,nsp-armpll";
clocks = <&osc>;
reg = <0x00000 0x1000>;
};
timer@20200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0x20200 0x100>;
interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
clocks = <&periph_clk>;
};
twd-timer@20600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0x20600 0x20>;
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_EDGE_RISING)>;
clocks = <&periph_clk>;
};
twd-watchdog@20620 {
compatible = "arm,cortex-a9-twd-wdt";
reg = <0x20620 0x20>;
interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&periph_clk>;
};
gic: interrupt-controller@21000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <3>;
#address-cells = <0>;
interrupt-controller;
reg = <0x21000 0x1000>,
<0x20100 0x100>;
};
L2: cache-controller@22000 {
compatible = "arm,pl310-cache";
reg = <0x22000 0x1000>;
cache-unified;
cache-level = <2>;
};
};
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
osc: oscillator {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <25000000>;
};
iprocmed: iprocmed {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
clock-div = <2>;
clock-mult = <1>;
};
iprocslow: iprocslow {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
clock-div = <4>;
clock-mult = <1>;
};
periph_clk: periph_clk {
#clock-cells = <0>;
compatible = "fixed-factor-clock";
clocks = <&a9pll>;
clock-div = <2>;
clock-mult = <1>;
};
};
axi: axi@18000000 {
compatible = "simple-bus";
ranges = <0x00000000 0x18000000 0x0011c40c>;
#address-cells = <1>;
#size-cells = <1>;
gpioa: gpio@20 {
compatible = "brcm,nsp-gpio-a";
reg = <0x0020 0x70>,
<0x3f1c4 0x1c>;
#gpio-cells = <2>;
gpio-controller;
ngpios = <32>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
gpio-ranges = <&pinctrl 0 0 32>;
};
uart0: serial@300 {
compatible = "ns16550a";
reg = <0x0300 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc>;
status = "disabled";
};
uart1: serial@400 {
compatible = "ns16550a";
reg = <0x0400 0x100>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc>;
status = "disabled";
};
dma: dma@20000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x20000 0x1000>;
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&iprocslow>;
clock-names = "apb_pclk";
#dma-cells = <1>;
dma-coherent;
status = "disabled";
};
sdio: mmc@21000 {
compatible = "brcm,sdhci-iproc-cygnus";
reg = <0x21000 0x100>;
interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
sdhci,auto-cmd12;
clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>;
dma-coherent;
status = "disabled";
};
amac0: ethernet@22000 {
compatible = "brcm,nsp-amac";
reg = <0x022000 0x1000>,
<0x110000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
amac1: ethernet@23000 {
compatible = "brcm,nsp-amac";
reg = <0x023000 0x1000>,
<0x111000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
amac2: ethernet@24000 {
compatible = "brcm,nsp-amac";
reg = <0x024000 0x1000>,
<0x112000 0x1000>;
reg-names = "amac_base", "idm_base";
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
mailbox: mailbox@25c00 {
compatible = "brcm,iproc-fa2-mbox";
reg = <0x25c00 0x400>;
interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
#mbox-cells = <1>;
brcm,rx-status-len = <32>;
brcm,use-bcm-hdr;
dma-coherent;
};
nand_controller: nand-controller@26000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
reg = <0x026000 0x600>,
<0x11b408 0x600>,
<0x026f00 0x20>;
reg-names = "nand", "iproc-idm", "iproc-ext";
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
brcm,nand-has-wp;
};
qspi: spi@27200 {
compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
reg = <0x027200 0x184>,
<0x027000 0x124>,
<0x11c408 0x004>,
<0x0273a0 0x01c>;
reg-names = "mspi", "bspi", "intr_regs",
"intr_status_reg";
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "spi_lr_fullness_reached",
"spi_lr_session_aborted",
"spi_lr_impatient",
"spi_lr_session_done",
"spi_lr_overhead",
"mspi_done",
"mspi_halted";
clocks = <&iprocmed>;
clock-names = "iprocmed";
num-cs = <2>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
xhci: usb@29000 {
compatible = "generic-xhci";
reg = <0x29000 0x1000>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb3_phy>;
phy-names = "usb3-phy";
dma-coherent;
status = "disabled";
};
ehci0: usb@2a000 {
compatible = "generic-ehci";
reg = <0x2a000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
ohci0: usb@2b000 {
compatible = "generic-ohci";
reg = <0x2b000 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
dma-coherent;
status = "disabled";
};
crypto@2f000 {
compatible = "brcm,spum-nsp-crypto";
reg = <0x2f000 0x900>;
mboxes = <&mailbox 0>;
};
gpiob: gpio@30000 {
compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
reg = <0x30000 0x50>;
#gpio-cells = <2>;
gpio-controller;
ngpios = <4>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
};
pwm: pwm@31000 {
compatible = "brcm,iproc-pwm";
reg = <0x31000 0x28>;
clocks = <&osc>;
#pwm-cells = <3>;
status = "disabled";
};
mdio: mdio@32000 {
compatible = "brcm,iproc-mdio";
reg = <0x32000 0x8>;
#size-cells = <0>;
#address-cells = <1>;
};
mdio-mux@32000 {
compatible = "mdio-mux-mmioreg", "mdio-mux";
reg = <0x32000 0x4>;
mux-mask = <0x200>;
#address-cells = <1>;
#size-cells = <0>;
mdio-parent-bus = <&mdio>;
mdio_int: mdio@0 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
usb3_phy: usb3-phy@10 {
compatible = "brcm,ns-bx-usb3-phy";
reg = <0x10>;
usb3-dmp-syscon = <&usb3_dmp>;
#phy-cells = <0>;
status = "disabled";
};
};
mdio_ext: mdio@200 {
reg = <0x200>;
#address-cells = <1>;
#size-cells = <0>;
};
};
rng: rng@33000 {
compatible = "brcm,bcm-nsp-rng";
reg = <0x33000 0x14>;
};
ccbtimer0: timer@34000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x34000 0x1000>;
interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&iprocslow>;
clock-names = "apb_pclk";
};
ccbtimer1: timer@35000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x35000 0x1000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&iprocslow>;
clock-names = "apb_pclk";
};
srab: ethernet-switch@36000 {
compatible = "brcm,nsp-srab";
reg = <0x36000 0x1000>,
<0x3f308 0x8>,
<0x3f410 0xc>;
reg-names = "srab", "mux_config", "sgmii_config";
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "link_state_p0",
"link_state_p1",
"link_state_p2",
"link_state_p3",
"link_state_p4",
"link_state_p5",
"link_state_p7",
"link_state_p8",
"phy",
"ts",
"imp_sleep_timer_p5",
"imp_sleep_timer_p7",
"imp_sleep_timer_p8";
status = "disabled";
/* ports are defined in board DTS */
ports {
#address-cells = <1>;
#size-cells = <0>;
};
};
i2c0: i2c@38000 {
compatible = "brcm,iproc-i2c";
reg = <0x38000 0x50>;
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <100000>;
dma-coherent;
status = "disabled";
};
watchdog@39000 {
compatible = "arm,sp805", "arm,primecell";
reg = <0x39000 0x1000>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&iprocslow>, <&iprocslow>;
clock-names = "wdog_clk", "apb_pclk";
};
lcpll0: lcpll0@3f100 {
#clock-cells = <1>;
compatible = "brcm,nsp-lcpll0";
reg = <0x3f100 0x14>;
clocks = <&osc>;
clock-output-names = "lcpll0", "pcie_phy", "sdio",
"ddr_phy";
};
genpll: genpll@3f140 {
#clock-cells = <1>;
compatible = "brcm,nsp-genpll";
reg = <0x3f140 0x24>;
clocks = <&osc>;
clock-output-names = "genpll", "phy", "ethernetclk",
"usbclk", "iprocfast", "sata1",
"sata2";
};
pinctrl: pinctrl@3f1c0 {
compatible = "brcm,nsp-pinmux";
reg = <0x3f1c0 0x04>,
<0x30028 0x04>,
<0x3f408 0x04>;
};
thermal: thermal@3f2c0 {
compatible = "brcm,ns-thermal";
reg = <0x3f2c0 0x10>;
#thermal-sensor-cells = <0>;
};
sata_phy: sata_phy@40100 {
compatible = "brcm,iproc-nsp-sata-phy";
reg = <0x40100 0x340>;
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
sata_phy0: sata-phy@0 {
reg = <0>;
#phy-cells = <0>;
status = "disabled";
};
sata_phy1: sata-phy@1 {
reg = <1>;
#phy-cells = <0>;
status = "disabled";
};
};
sata: sata@41000 {
compatible = "brcm,bcm-nsp-ahci";
reg-names = "ahci", "top-ctrl";
reg = <0x41000 0x1000>, <0x40020 0x1c>;
interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
dma-coherent;
status = "disabled";
sata0: sata-port@0 {
reg = <0>;
phys = <&sata_phy0>;
phy-names = "sata-phy";
};
sata1: sata-port@1 {
reg = <1>;
phys = <&sata_phy1>;
phy-names = "sata-phy";
};
};
usb3_dmp: syscon@104000 {
reg = <0x104000 0x1000>;
};
};
pcie0: pcie@18012000 {
compatible = "brcm,iproc-pcie";
reg = <0x18012000 0x1000>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
/* Note: The HW does not support I/O resources. So,
* only the memory resource range is being specified.
*/
ranges = <0x82000000 0 0x08000000 0x08000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi0>;
msi0: msi {
compatible = "brcm,iproc-msi";
msi-controller;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
brcm,pcie-msi-inten;
};
};
pcie1: pcie@18013000 {
compatible = "brcm,iproc-pcie";
reg = <0x18013000 0x1000>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
linux,pci-domain = <1>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
/* Note: The HW does not support I/O resources. So,
* only the memory resource range is being specified.
*/
ranges = <0x82000000 0 0x40000000 0x40000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi1>;
msi1: msi {
compatible = "brcm,iproc-msi";
msi-controller;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
brcm,pcie-msi-inten;
};
};
pcie2: pcie@18014000 {
compatible = "brcm,iproc-pcie";
reg = <0x18014000 0x1000>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
linux,pci-domain = <2>;
bus-range = <0x00 0xff>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
/* Note: The HW does not support I/O resources. So,
* only the memory resource range is being specified.
*/
ranges = <0x82000000 0 0x48000000 0x48000000 0 0x8000000>;
dma-coherent;
status = "disabled";
msi-parent = <&msi2>;
msi2: msi {
compatible = "brcm,iproc-msi";
msi-controller;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
brcm,pcie-msi-inten;
};
};
thermal-zones {
cpu-thermal {
polling-delay-passive = <0>;
polling-delay = <1000>;
coefficients = <(-556) 418000>;
thermal-sensors = <&thermal>;
trips {
cpu-crit {
temperature = <125000>;
hysteresis = <0>;
type = "critical";
};
};
cooling-maps {
};
};
};
};
Codebase Browser
linux