// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "qcom-apq8064-v2.0.dtsi"
#include "pm8821.dtsi"
#include "pm8921.dtsi"
/ {
model = "Qualcomm APQ8064/IFC6410";
compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
aliases {
serial0 = &gsbi7_serial;
serial1 = &gsbi6_serial;
i2c0 = &gsbi1_i2c;
i2c1 = &gsbi2_i2c;
i2c2 = &gsbi3_i2c;
i2c3 = &gsbi4_i2c;
spi0 = &gsbi5_spi;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <¬ify_led>;
led-user1 {
label = "apq8064:green:user1";
color = <LED_COLOR_ID_GREEN>;
gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
};
hdmi-out {
compatible = "hdmi-connector";
type = "d";
port {
hdmi_con: endpoint {
remote-endpoint = <&hdmi_out>;
};
};
};
sdcc4_pwrseq: pwrseq-sdcc4 {
pinctrl-names = "default";
pinctrl-0 = <&wlan_default_gpios>;
compatible = "mmc-pwrseq-simple";
reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
};
ext_3p3v: regulator-ext-3p3v {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "ext_3p3v";
startup-delay-us = <0>;
gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-boot-on;
};
};
&gsbi1 {
qcom,mode = <GSBI_PROT_I2C>;
status = "okay";
};
&gsbi1_i2c {
clock-frequency = <200000>;
status = "okay";
eeprom@52 {
compatible = "atmel,24c128";
reg = <0x52>;
pagesize = <32>;
};
};
&gsbi3 {
qcom,mode = <GSBI_PROT_I2C>;
status = "okay";
};
&gsbi3_i2c {
status = "okay";
};
&gsbi4 {
qcom,mode = <GSBI_PROT_I2C>;
status = "okay";
};
/* CAM I2C MIPI-CSI connector */
&gsbi4_i2c {
status = "okay";
};
&gsbi5 {
qcom,mode = <GSBI_PROT_SPI>;
status = "okay";
};
&gsbi5_spi {
num-cs = <1>;
cs-gpios = <&tlmm_pinmux 53 0>;
status = "okay";
};
&gsbi6 {
qcom,mode = <GSBI_PROT_UART_W_FC>;
status = "okay";
};
&gsbi6_serial {
pinctrl-names = "default";
pinctrl-0 = <&gsbi6_uart_4pins>;
status = "okay";
};
&gsbi7 {
qcom,mode = <GSBI_PROT_I2C_UART>;
status = "okay";
};
&gsbi7_serial {
pinctrl-names = "default";
pinctrl-0 = <&gsbi7_uart_2pins>;
status = "okay";
};
&hdmi {
core-vdda-supply = <&pm8921_hdmi_switch>;
hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&hdmi_in {
remote-endpoint = <&mdp_dtv_out>;
};
&hdmi_out {
remote-endpoint = <&hdmi_con>;
};
&hdmi_phy {
status = "okay";
core-vdda-supply = <&pm8921_hdmi_switch>;
};
&mdp {
status = "okay";
};
&mdp_dtv_out {
remote-endpoint = <&hdmi_in>;
};
&pcie {
status = "okay";
vdda-supply = <&pm8921_s3>;
vdda_phy-supply = <&pm8921_lvs6>;
vdda_refclk-supply = <&ext_3p3v>;
pinctrl-0 = <&pcie_pins>;
pinctrl-names = "default";
perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
};
&pm8821 {
interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
};
&pm8921 {
interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
};
&pm8921_gpio {
wlan_default_gpios: wlan-gpios-state {
pinconf {
pins = "gpio43";
function = "normal";
bias-disable;
power-source = <PM8921_GPIO_S4>;
};
};
notify_led: nled-state {
pinconf {
pins = "gpio18";
function = "normal";
bias-disable;
power-source = <PM8921_GPIO_S4>;
};
};
};
&rpm {
regulators {
compatible = "qcom,rpm-pm8921-regulators";
vin_lvs1_3_6-supply = <&pm8921_s4>;
vin_lvs2-supply = <&pm8921_s1>;
vin_lvs4_5_7-supply = <&pm8921_s4>;
vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
vdd_l24-supply = <&pm8921_s1>;
vdd_l25-supply = <&pm8921_s1>;
vdd_l26-supply = <&pm8921_s7>;
vdd_l27-supply = <&pm8921_s7>;
vdd_l28-supply = <&pm8921_s7>;
/* Buck SMPS */
pm8921_s1: s1 {
regulator-always-on;
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
qcom,switch-mode-frequency = <3200000>;
bias-pull-down;
};
pm8921_s3: s3 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
qcom,switch-mode-frequency = <4800000>;
};
pm8921_s4: s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
qcom,switch-mode-frequency = <3200000>;
};
pm8921_s7: s7 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
qcom,switch-mode-frequency = <3200000>;
};
pm8921_l3: l3 {
regulator-min-microvolt = <3050000>;
regulator-max-microvolt = <3300000>;
bias-pull-down;
};
pm8921_l4: l4 {
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1800000>;
bias-pull-down;
};
pm8921_l5: l5 {
regulator-min-microvolt = <2750000>;
regulator-max-microvolt = <3000000>;
bias-pull-down;
};
pm8921_l6: l6 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
bias-pull-down;
};
pm8921_l23: l23 {
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
bias-pull-down;
};
pm8921_lvs1: lvs1 {
bias-pull-down;
};
pm8921_lvs6: lvs6 {
bias-pull-down;
};
pm8921_hdmi_switch: hdmi-switch {
bias-pull-down;
};
};
};
&sata_phy0 {
status = "okay";
};
&sata0 {
target-supply = <&pm8921_s4>;
status = "okay";
};
/* eMMC */
&sdcc1 {
vmmc-supply = <&pm8921_l5>;
vqmmc-supply = <&pm8921_s4>;
status = "okay";
};
/* External micro SD card */
&sdcc3 {
vmmc-supply = <&pm8921_l6>;
pinctrl-names = "default";
pinctrl-0 = <&card_detect>;
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
status = "okay";
};
/* WLAN */
&sdcc4 {
vmmc-supply = <&ext_3p3v>;
vqmmc-supply = <&pm8921_lvs1>;
mmc-pwrseq = <&sdcc4_pwrseq>;
status = "okay";
};
&tlmm_pinmux {
card_detect: card_detect {
mux {
pins = "gpio26";
function = "gpio";
bias-disable;
};
};
pcie_pins: pcie_pinmux {
mux {
pins = "gpio27";
function = "gpio";
};
conf {
pins = "gpio27";
drive-strength = <12>;
bias-disable;
};
};
};
&usb_hs1_phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l4>;
};
&usb_hs3_phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l23>;
};
&usb_hs4_phy {
v3p3-supply = <&pm8921_l3>;
v1p8-supply = <&pm8921_l23>;
};
/* OTG */
&usb1 {
dr_mode = "otg";
status = "okay";
};
&usb3 {
dr_mode = "host";
status = "okay";
};
&usb4 {
dr_mode = "host";
status = "okay";
};
Codebase Browser
linux