// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "qcom-msm8974.dtsi"
#include "pm8841.dtsi"
#include "pm8941.dtsi"
/delete-node/ &mpss_region;
/ {
model = "Qualcomm APQ8074 Dragonboard";
compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
aliases {
serial0 = &blsp1_uart2;
usid0 = &pm8941_0;
usid4 = &pm8841_0;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
pinctrl-0 = <&msm_keys_default>;
pinctrl-names = "default";
button-volup {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
};
button-general {
label = "General";
linux,code = <KEY_PROG1>;
gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
};
};
reserved-memory {
mpss_region: mpss@ac00000 {
reg = <0x0ac00000 0x2500000>;
no-map;
};
};
vreg_boost: vreg-boost {
compatible = "regulator-fixed";
regulator-name = "vreg-boost";
regulator-min-microvolt = <3150000>;
regulator-max-microvolt = <3150000>;
regulator-always-on;
regulator-boot-on;
gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&boost_bypass_n_pin>;
};
vreg_vph_pwr: vreg-vph-pwr {
compatible = "regulator-fixed";
regulator-name = "vph-pwr";
regulator-min-microvolt = <3600000>;
regulator-max-microvolt = <3600000>;
regulator-always-on;
};
};
&blsp1_uart2 {
status = "okay";
};
&blsp2_dma {
qcom,controlled-remotely;
};
&blsp2_i2c5 {
status = "okay";
clock-frequency = <200000>;
eeprom: eeprom@52 {
compatible = "atmel,24c128";
reg = <0x52>;
pagesize = <32>;
read-only;
};
};
&gpu {
status = "okay";
};
&mdss {
status = "okay";
};
&mdss_dsi0 {
vdda-supply = <&pm8941_l2>;
vdd-supply = <&pm8941_l22>;
vddio-supply = <&pm8941_l12>;
status = "okay";
panel: panel@0 {
compatible = "sharp,ls043t1le01-qhd";
reg = <0>;
avdd-supply = <&pm8941_l22>;
backlight = <&pm8941_wled>;
reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>;
port {
panel_in: endpoint {
remote-endpoint = <&mdss_dsi0_out>;
};
};
};
};
&mdss_dsi0_out {
remote-endpoint = <&panel_in>;
data-lanes = <0 1 2 3>;
};
&mdss_dsi0_phy {
status = "okay";
vddio-supply = <&pm8941_l12>;
};
&gpu {
status = "okay";
};
&mdss {
status = "okay";
};
&pm8941_gpios {
msm_keys_default: pm8941-gpio-keys-state {
pins = "gpio5", "gpio23";
function = "normal";
input-enable;
drive-push-pull;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
power-source = <PM8941_GPIO_S3>; /* 1.8V */
};
};
&pm8941_lpg {
qcom,power-source = <1>;
status = "okay";
led@5 {
reg = <5>;
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_INDICATOR;
};
led@6 {
reg = <6>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_INDICATOR;
};
led@7 {
reg = <7>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_INDICATOR;
};
};
&pm8941_resin {
linux,code = <KEY_VOLUMEDOWN>;
status = "okay";
};
&pm8941_wled {
qcom,cs-out;
qcom,switching-freq = <3200>;
qcom,ovp = <32>;
qcom,num-strings = <1>;
status = "okay";
};
&remoteproc_adsp {
cx-supply = <&pm8841_s2>;
firmware-name = "qcom/apq8074/adsp.mbn";
status = "okay";
};
&remoteproc_mss {
cx-supply = <&pm8841_s2>;
mss-supply = <&pm8841_s3>;
mx-supply = <&pm8841_s1>;
pll-supply = <&pm8941_l12>;
firmware-name = "qcom/apq8074/mba.mbn", "qcom/apq8074/modem.mbn";
status = "okay";
};
&rpm_requests {
regulators-0 {
compatible = "qcom,rpm-pm8841-regulators";
pm8841_s1: s1 {
regulator-min-microvolt = <675000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s2: s2 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s3: s3 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
pm8841_s4: s4 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1050000>;
};
};
regulators-1 {
compatible = "qcom,rpm-pm8941-regulators";
vdd_l1_l3-supply = <&pm8941_s1>;
vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
vdd_l4_l11-supply = <&pm8941_s1>;
vdd_l5_l7-supply = <&pm8941_s2>;
vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
vin_5vs-supply = <&pm8941_5v>;
pm8941_s1: s1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_s2: s2 {
regulator-min-microvolt = <2150000>;
regulator-max-microvolt = <2150000>;
regulator-boot-on;
};
pm8941_s3: s3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l1: l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l2: l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
pm8941_l3: l3 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
pm8941_l4: l4 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
pm8941_l5: l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l6: l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l7: l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
pm8941_l8: l8 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l9: l9 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
pm8941_l10: l10 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
pm8941_l11: l11 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
};
pm8941_l12: l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
pm8941_l13: l13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l14: l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
pm8941_l15: l15 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
pm8941_l16: l16 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8941_l17: l17 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
pm8941_l18: l18 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
pm8941_l19: l19 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
pm8941_l20: l20 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-system-load = <200000>;
regulator-allow-set-load;
regulator-boot-on;
};
pm8941_l21: l21 {
regulator-min-microvolt = <2950000>;
regulator-max-microvolt = <2950000>;
regulator-boot-on;
};
pm8941_l22: l22 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8941_l23: l23 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
pm8941_l24: l24 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
regulator-boot-on;
};
};
};
&sdhc_1 {
status = "okay";
vmmc-supply = <&pm8941_l20>;
vqmmc-supply = <&pm8941_s3>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_on>;
pinctrl-1 = <&sdc1_off>;
};
&sdhc_2 {
status = "okay";
cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
vmmc-supply = <&pm8941_l21>;
vqmmc-supply = <&pm8941_l13>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_on>;
pinctrl-1 = <&sdc2_off>;
};
&smbb {
status = "okay";
};
&tlmm {
sdc1_on: sdc1-on-state {
clk-pins {
pins = "sdc1_clk";
drive-strength = <16>;
bias-disable;
};
cmd-data-pins {
pins = "sdc1_cmd", "sdc1_data";
drive-strength = <10>;
bias-pull-up;
};
};
sdc2_on: sdc2-on-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <10>;
bias-disable;
};
cmd-data-pins {
pins = "sdc2_cmd", "sdc2_data";
drive-strength = <6>;
bias-pull-up;
};
cd-pins {
pins = "gpio62";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
};
};
&usb {
status = "okay";
phys = <&usb_hs2_phy>;
phy-select = <&tcsr 0xb000 1>;
extcon = <&smbb>, <&usb_id>;
vbus-supply = <&chg_otg>;
hnp-disable;
srp-disable;
adp-disable;
};
&usb_hs2_phy {
status = "okay";
v3p3-supply = <&pm8941_l24>;
v1p8-supply = <&pm8941_l6>;
extcon = <&smbb>;
qcom,init-seq = /bits/ 8 <0x1 0x63>;
};
Codebase Browser
linux