# SPDX-License-Identifier: GPL-2.0
#
# USB Dual Role (OTG-ready) Controller Drivers
# for silicon based on Mentor Graphics INVENTRA designs
#
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
config USB_MUSB_HDRC
tristate 'Inventra Highspeed Dual Role Controller'
depends on (USB || USB_GADGET)
depends on HAS_IOMEM
help
Say Y here if your system has a dual role high speed USB
controller based on the Mentor Graphics silicon IP. Then
configure options to match your silicon and the board
it's being used with, including the USB peripheral role,
or the USB host role, or both.
Texas Instruments families using this IP include DaVinci
(35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010.
Allwinner SoCs using this IP include A10, A13, A20, ...
If you do not know what this is, please say N.
To compile this driver as a module, choose M here; the
module will be called "musb-hdrc".
if USB_MUSB_HDRC
choice
bool "MUSB Mode Selection"
default USB_MUSB_DUAL_ROLE if (USB && USB_GADGET)
default USB_MUSB_HOST if (USB && !USB_GADGET)
default USB_MUSB_GADGET if (!USB && USB_GADGET)
config USB_MUSB_HOST
bool "Host only mode"
depends on USB=y || USB=USB_MUSB_HDRC
help
Select this when you want to use MUSB in host mode only,
thereby the gadget feature will be regressed.
config USB_MUSB_GADGET
bool "Gadget only mode"
depends on USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC
depends on HAS_DMA
help
Select this when you want to use MUSB in gadget mode only,
thereby the host feature will be regressed.
config USB_MUSB_DUAL_ROLE
bool "Dual Role mode"
depends on ((USB=y || USB=USB_MUSB_HDRC) && (USB_GADGET=y || USB_GADGET=USB_MUSB_HDRC))
depends on HAS_DMA
help
This is the default mode of working of MUSB controller where
both host and gadget features are enabled.
endchoice
comment "Platform Glue Layer"
config USB_MUSB_SUNXI
tristate "Allwinner (sunxi)"
depends on ARCH_SUNXI
depends on NOP_USB_XCEIV
depends on PHY_SUN4I_USB
depends on EXTCON
select GENERIC_PHY
select SUNXI_SRAM
config USB_MUSB_DA8XX
tristate "DA8xx/OMAP-L1x"
depends on ARCH_DAVINCI_DA8XX
depends on NOP_USB_XCEIV
select PHY_DA8XX_USB
config USB_MUSB_TUSB6010
tristate "TUSB6010"
depends on HAS_IOMEM
depends on ARCH_OMAP2PLUS || COMPILE_TEST
depends on NOP_USB_XCEIV!=m || USB_MUSB_HDRC=m
config USB_MUSB_OMAP2PLUS
tristate "OMAP2430 and onwards"
depends on ARCH_OMAP2PLUS && USB
depends on OMAP_CONTROL_PHY || !OMAP_CONTROL_PHY
select GENERIC_PHY
config USB_MUSB_DSPS
tristate "TI DSPS platforms"
depends on ARCH_OMAP2PLUS || COMPILE_TEST
depends on OF_IRQ
config USB_MUSB_UX500
tristate "Ux500 platforms"
depends on ARCH_U8500 || COMPILE_TEST
config USB_MUSB_JZ4740
tristate "JZ4740"
depends on OF
depends on MIPS || COMPILE_TEST
depends on USB_MUSB_GADGET
select USB_ROLE_SWITCH
config USB_MUSB_MEDIATEK
tristate "MediaTek platforms"
depends on ARCH_MEDIATEK || COMPILE_TEST
depends on NOP_USB_XCEIV
select GENERIC_PHY
select USB_ROLE_SWITCH
config USB_MUSB_POLARFIRE_SOC
tristate "Microchip PolarFire SoC platforms"
depends on ARCH_MICROCHIP_POLARFIRE || COMPILE_TEST
depends on NOP_USB_XCEIV
select USB_MUSB_DUAL_ROLE
help
Say Y here to enable support for USB on Microchip's PolarFire SoC.
This support is also available as a module. If so, the module
will be called mpfs.
comment "MUSB DMA mode"
config MUSB_PIO_ONLY
bool 'Disable DMA (always use PIO)'
help
All data is copied between memory and FIFO by the CPU.
DMA controllers are ignored.
Do not choose this unless DMA support for your SOC or board
is unavailable (or unstable). When DMA is enabled at compile time,
you can still disable it at run time using the "use_dma=n" module
parameter.
if !MUSB_PIO_ONLY
config USB_UX500_DMA
bool 'ST Ericsson Ux500'
depends on USB_MUSB_UX500
help
Enable DMA transfers on UX500 platforms.
config USB_INVENTRA_DMA
bool 'Inventra'
depends on USB_MUSB_OMAP2PLUS || USB_MUSB_MEDIATEK || USB_MUSB_JZ4740 || USB_MUSB_POLARFIRE_SOC
help
Enable DMA transfers using Mentor's engine.
config USB_TI_CPPI41_DMA
bool 'TI CPPI 4.1'
depends on (ARCH_OMAP || ARCH_DAVINCI_DA8XX) && DMADEVICES
select TI_CPPI41
config USB_TUSB_OMAP_DMA
bool 'TUSB 6010'
depends on USB_MUSB_TUSB6010 = USB_MUSB_HDRC # both built-in or both modules
depends on ARCH_OMAP
help
Enable DMA transfers on TUSB 6010 when OMAP DMA is available.
endif # !MUSB_PIO_ONLY
endif # USB_MUSB_HDRC
Codebase Browser
linux