# SPDX-License-Identifier: GPL-2.0-only
#
# Watchdog device configuration
#
menuconfig WATCHDOG
bool "Watchdog Timer Support"
help
If you say Y here (and to one of the following options) and create a
character special file /dev/watchdog with major number 10 and minor
number 130 using mknod ("man mknod"), you will get a watchdog, i.e.:
subsequently opening the file and then failing to write to it for
longer than 1 minute will result in rebooting the machine. This
could be useful for a networked machine that needs to come back
on-line as fast as possible after a lock-up. There's both a watchdog
implementation entirely in software (which can sometimes fail to
reboot the machine) and a driver for hardware watchdog boards, which
are more robust and can also keep track of the temperature inside
your computer. For details, read
<file:Documentation/watchdog/watchdog-api.rst> in the kernel source.
The watchdog is usually used together with the watchdog daemon
which is available from
<https://ibiblio.org/pub/Linux/system/daemons/watchdog/>. This daemon
can also monitor NFS connections and can reboot the machine when the
process table is full.
If unsure, say N.
if WATCHDOG
config WATCHDOG_CORE
tristate "WatchDog Timer Driver Core"
help
Say Y here if you want to use the new watchdog timer driver core.
This driver provides a framework for all watchdog timer drivers
and gives them the /dev/watchdog interface (and later also the
sysfs interface).
config WATCHDOG_NOWAYOUT
bool "Disable watchdog shutdown on close"
help
The default watchdog behaviour (which you get if you say N here) is
to stop the timer if the process managing it closes the file
/dev/watchdog. It's always remotely possible that this process might
get killed. If you say Y here, the watchdog cannot be stopped once
it has been started.
config WATCHDOG_HANDLE_BOOT_ENABLED
bool "Update boot-enabled watchdog until userspace takes over"
default y
help
The default watchdog behaviour (which you get if you say Y here) is
to ping watchdog devices that were enabled before the driver has
been loaded until control is taken over from userspace using the
/dev/watchdog file. If you say N here, the kernel will not update
the watchdog on its own. Thus if your userspace does not start fast
enough your device will reboot.
config WATCHDOG_OPEN_TIMEOUT
int "Timeout value for opening watchdog device"
default 0
help
The maximum time, in seconds, for which the watchdog framework takes
care of pinging a hardware watchdog. A value of 0 means infinite. The
value set here can be overridden by the commandline parameter
"watchdog.open_timeout".
config WATCHDOG_SYSFS
bool "Read different watchdog information through sysfs"
help
Say Y here if you want to enable watchdog device status read through
sysfs attributes.
config WATCHDOG_HRTIMER_PRETIMEOUT
bool "Enable watchdog hrtimer-based pretimeouts"
help
Enable this if you want to use a hrtimer timer based pretimeout for
watchdogs that do not natively support pretimeout support. Be aware
that because this pretimeout functionality uses hrtimers, it may not
be able to fire before the actual watchdog fires in some situations.
comment "Watchdog Pretimeout Governors"
config WATCHDOG_PRETIMEOUT_GOV
bool "Enable watchdog pretimeout governors"
depends on WATCHDOG_CORE
help
The option allows to select watchdog pretimeout governors.
config WATCHDOG_PRETIMEOUT_GOV_SEL
tristate
depends on WATCHDOG_PRETIMEOUT_GOV
default m
select WATCHDOG_PRETIMEOUT_GOV_PANIC if WATCHDOG_PRETIMEOUT_GOV_NOOP=n
if WATCHDOG_PRETIMEOUT_GOV
config WATCHDOG_PRETIMEOUT_GOV_NOOP
tristate "Noop watchdog pretimeout governor"
depends on WATCHDOG_CORE
default WATCHDOG_CORE
help
Noop watchdog pretimeout governor, only an informational
message is added to kernel log buffer.
config WATCHDOG_PRETIMEOUT_GOV_PANIC
tristate "Panic watchdog pretimeout governor"
depends on WATCHDOG_CORE
default WATCHDOG_CORE
help
Panic watchdog pretimeout governor, on watchdog pretimeout
event put the kernel into panic.
choice
prompt "Default Watchdog Pretimeout Governor"
default WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC
help
This option selects a default watchdog pretimeout governor.
The governor takes its action, if a watchdog is capable
to report a pretimeout event.
config WATCHDOG_PRETIMEOUT_DEFAULT_GOV_NOOP
bool "noop"
depends on WATCHDOG_PRETIMEOUT_GOV_NOOP
help
Use noop watchdog pretimeout governor by default. If noop
governor is selected by a user, write a short message to
the kernel log buffer and don't do any system changes.
config WATCHDOG_PRETIMEOUT_DEFAULT_GOV_PANIC
bool "panic"
depends on WATCHDOG_PRETIMEOUT_GOV_PANIC
help
Use panic watchdog pretimeout governor by default, if
a watchdog pretimeout event happens, consider that
a watchdog feeder is dead and reboot is unavoidable.
endchoice
endif # WATCHDOG_PRETIMEOUT_GOV
#
# General Watchdog drivers
#
comment "Watchdog Device Drivers"
# Architecture Independent
config SOFT_WATCHDOG
tristate "Software watchdog"
select WATCHDOG_CORE
help
A software monitoring watchdog. This will fail to reboot your system
from some situations that the hardware watchdog will recover
from. Equally it's a lot cheaper to install.
To compile this driver as a module, choose M here: the
module will be called softdog.
config SOFT_WATCHDOG_PRETIMEOUT
bool "Software watchdog pretimeout governor support"
depends on SOFT_WATCHDOG && WATCHDOG_PRETIMEOUT_GOV
help
Enable this if you want to use pretimeout governors with the software
watchdog. Be aware that governors might affect the watchdog because it
is purely software, e.g. the panic governor will stall it!
config BD957XMUF_WATCHDOG
tristate "ROHM BD9576MUF and BD9573MUF PMIC Watchdog"
depends on MFD_ROHM_BD957XMUF
select WATCHDOG_CORE
help
Support for the watchdog in the ROHM BD9576 and BD9573 PMICs.
These PMIC ICs contain watchdog block which can be configured
to toggle reset line if SoC fails to ping watchdog via GPIO.
Say Y here to include support for the ROHM BD9576 or BD9573
watchdog. Alternatively say M to compile the driver as a module,
which will be called bd9576_wdt.
config BD96801_WATCHDOG
tristate "ROHM BD96801 PMIC Watchdog"
depends on MFD_ROHM_BD96801
select WATCHDOG_CORE
help
Support for the watchdog in the ROHM BD96801 PMIC. Watchdog can be
configured to only generate IRQ or to trigger system reset via reset
pin.
Say Y here to include support for the ROHM BD96801 watchdog.
Alternatively say M to compile the driver as a module,
which will be called bd96801_wdt.
config CROS_EC_WATCHDOG
tristate "ChromeOS EC-based watchdog"
select WATCHDOG_CORE
depends on CROS_EC
help
Watchdog driver for Chromebook devices equipped with embedded controller.
Trigger event is recorded in EC and checked on the subsequent boot.
To compile this driver as a module, choose M here: the
module will be called cros_ec_wdt.
config DA9052_WATCHDOG
tristate "Dialog DA9052 Watchdog"
depends on PMIC_DA9052 || COMPILE_TEST
select WATCHDOG_CORE
help
Support for the watchdog in the DA9052 PMIC. Watchdog trigger
cause system reset.
Say Y here to include support for the DA9052 watchdog.
Alternatively say M to compile the driver as a module,
which will be called da9052_wdt.
config DA9055_WATCHDOG
tristate "Dialog Semiconductor DA9055 Watchdog"
depends on MFD_DA9055 || COMPILE_TEST
select WATCHDOG_CORE
help
If you say yes here you get support for watchdog on the Dialog
Semiconductor DA9055 PMIC.
This driver can also be built as a module. If so, the module
will be called da9055_wdt.
config DA9063_WATCHDOG
tristate "Dialog DA9063 Watchdog"
depends on MFD_DA9063 || COMPILE_TEST
depends on I2C
select WATCHDOG_CORE
help
Support for the watchdog in the DA9063 PMIC.
This driver can be built as a module. The module name is da9063_wdt.
config DA9062_WATCHDOG
tristate "Dialog DA9062/61 Watchdog"
depends on MFD_DA9062 || COMPILE_TEST
depends on I2C
select WATCHDOG_CORE
help
Support for the watchdog in the DA9062 and DA9061 PMICs.
This driver can be built as a module. The module name is da9062_wdt.
config GPIO_WATCHDOG
tristate "Watchdog device controlled through GPIO-line"
depends on OF_GPIO
select WATCHDOG_CORE
help
If you say yes here you get support for watchdog device
controlled through GPIO-line.
config GPIO_WATCHDOG_ARCH_INITCALL
bool "Register the watchdog as early as possible"
depends on GPIO_WATCHDOG=y
help
In some situations, the default initcall level (module_init)
in not early enough in the boot process to avoid the watchdog
to be triggered.
If you say yes here, the initcall level would be raised to
arch_initcall.
If in doubt, say N.
config LENOVO_SE10_WDT
tristate "Lenovo SE10 Watchdog"
depends on (X86 && DMI) || COMPILE_TEST
depends on HAS_IOPORT
select WATCHDOG_CORE
help
If you say yes here you get support for the watchdog
functionality for the Lenovo SE10 platform.
This driver can also be built as a module. If so, the module
will be called lenovo-se10-wdt.
config MENF21BMC_WATCHDOG
tristate "MEN 14F021P00 BMC Watchdog"
depends on MFD_MENF21BMC || COMPILE_TEST
depends on I2C
select WATCHDOG_CORE
help
Say Y here to include support for the MEN 14F021P00 BMC Watchdog.
This driver can also be built as a module. If so the module
will be called menf21bmc_wdt.
config MENZ069_WATCHDOG
tristate "MEN 16Z069 Watchdog"
depends on MCB
select WATCHDOG_CORE
help
Say Y here to include support for the MEN 16Z069 Watchdog.
This driver can also be built as a module. If so the module
will be called menz069_wdt.
config WDAT_WDT
tristate "ACPI Watchdog Action Table (WDAT)"
depends on ACPI
select WATCHDOG_CORE
select ACPI_WATCHDOG
help
This driver adds support for systems with ACPI Watchdog Action
Table (WDAT) table. Servers typically have this but it can be
found on some desktop machines as well. This driver will take
over the native iTCO watchdog driver found on many Intel CPUs.
To compile this driver as module, choose M here: the module will
be called wdat_wdt.
config WM831X_WATCHDOG
tristate "WM831x watchdog"
depends on MFD_WM831X
select WATCHDOG_CORE
help
Support for the watchdog in the WM831x AudioPlus PMICs. When
the watchdog triggers the system will be reset.
config WM8350_WATCHDOG
tristate "WM8350 watchdog"
depends on MFD_WM8350
select WATCHDOG_CORE
help
Support for the watchdog in the WM8350 AudioPlus PMIC. When
the watchdog triggers the system will be reset.
config XILINX_WATCHDOG
tristate "Xilinx Watchdog timer"
depends on HAS_IOMEM
select WATCHDOG_CORE
help
Watchdog driver for the xps_timebase_wdt IP core.
To compile this driver as a module, choose M here: the
module will be called of_xilinx_wdt.
config XILINX_WINDOW_WATCHDOG
tristate "Xilinx window watchdog timer"
depends on HAS_IOMEM
depends on ARM64 || COMPILE_TEST
select WATCHDOG_CORE
help
Window watchdog driver for the versal_wwdt IP core.
Window watchdog timer(WWDT) contains closed(first) and
open(second) window with 32 bit width. Write to the watchdog
timer within predefined window periods of time. This means
a period that is not too soon and a period that is not too
late. The WWDT has to be restarted within the open window time.
If software tries to restart WWDT outside of the open window
time period, it generates a reset.
To compile this driver as a module, choose M here: the
module will be called xilinx_wwdt.
config ZIIRAVE_WATCHDOG
tristate "Zodiac RAVE Watchdog Timer"
depends on I2C
select WATCHDOG_CORE
help
Watchdog driver for the Zodiac Aerospace RAVE Switch Watchdog
Processor.
To compile this driver as a module, choose M here: the
module will be called ziirave_wdt.
config RAVE_SP_WATCHDOG
tristate "RAVE SP Watchdog timer"
depends on RAVE_SP_CORE
depends on NVMEM || !NVMEM
select WATCHDOG_CORE
help
Support for the watchdog on RAVE SP device.
config MLX_WDT
tristate "Mellanox Watchdog"
depends on MELLANOX_PLATFORM || COMPILE_TEST
select WATCHDOG_CORE
select REGMAP
help
This is the driver for the hardware watchdog on Mellanox systems.
If you are going to use it, say Y here, otherwise N.
This driver can be used together with the watchdog daemon.
It can also watch your kernel to make sure it doesn't freeze,
and if it does, it reboots your system after a certain amount of
time.
To compile this driver as a module, choose M here: the
module will be called mlx-wdt.
config SL28CPLD_WATCHDOG
tristate "Kontron sl28cpld Watchdog"
depends on MFD_SL28CPLD || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
on the Kontron sl28 CPLD.
To compile this driver as a module, choose M here: the
module will be called sl28cpld_wdt.
# ALPHA Architecture
# ARM Architecture
config ARM_SP805_WATCHDOG
tristate "ARM SP805 Watchdog"
depends on (ARM || ARM64 || COMPILE_TEST) && ARM_AMBA
select WATCHDOG_CORE
help
ARM Primecell SP805 Watchdog timer. This will reboot your system when
the timeout is reached.
config ARM_SBSA_WATCHDOG
tristate "ARM SBSA Generic Watchdog"
depends on ARM64
depends on ARM_ARCH_TIMER
select WATCHDOG_CORE
help
ARM SBSA Generic Watchdog has two stage timeouts:
the first signal (WS0) is for alerting the system by interrupt,
the second one (WS1) is a real hardware reset.
More details: ARM DEN0029B - Server Base System Architecture (SBSA)
This driver can operate ARM SBSA Generic Watchdog as a single stage
or a two stages watchdog, it depends on the module parameter "action".
Note: the maximum timeout in the two stages mode is half of that in
the single stage mode.
To compile this driver as module, choose M here: The module
will be called sbsa_gwdt.
config ARMADA_37XX_WATCHDOG
tristate "Armada 37xx watchdog"
depends on ARCH_MVEBU || COMPILE_TEST
depends on HAS_IOMEM
select MFD_SYSCON
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer found on
Marvell Armada 37xx SoCs.
To compile this driver as a module, choose M here: the
module will be called armada_37xx_wdt.
config ASM9260_WATCHDOG
tristate "Alphascale ASM9260 watchdog"
depends on MACH_ASM9260 || COMPILE_TEST
depends on OF
select WATCHDOG_CORE
select RESET_CONTROLLER
help
Watchdog timer embedded into Alphascale asm9260 chips. This will
reboot your system when the timeout is reached.
config AT91RM9200_WATCHDOG
tristate "AT91RM9200 watchdog"
depends on (SOC_AT91RM9200 && MFD_SYSCON) || COMPILE_TEST
help
Watchdog timer embedded into AT91RM9200 chips. This will reboot your
system when the timeout is reached.
config AT91SAM9X_WATCHDOG
tristate "AT91SAM9X / AT91CAP9 watchdog"
depends on ARCH_AT91 || COMPILE_TEST
select WATCHDOG_CORE
help
Watchdog timer embedded into AT91SAM9X and AT91CAP9 chips. This will
reboot your system when the timeout is reached.
config SAMA5D4_WATCHDOG
tristate "Atmel SAMA5D4 Watchdog Timer"
depends on ARCH_AT91 || COMPILE_TEST
select WATCHDOG_CORE
help
Atmel SAMA5D4 watchdog timer is embedded into SAMA5D4 chips.
Its Watchdog Timer Mode Register can be written more than once.
This will reboot your system when the timeout is reached.
config CADENCE_WATCHDOG
tristate "Cadence Watchdog Timer"
depends on HAS_IOMEM
select WATCHDOG_CORE
help
Say Y here if you want to include support for the watchdog
timer in the Xilinx Zynq.
config 21285_WATCHDOG
tristate "DC21285 watchdog"
depends on FOOTBRIDGE
help
The Intel Footbridge chip contains a built-in watchdog circuit. Say Y
here if you wish to use this. Alternatively say M to compile the
driver as a module, which will be called wdt285.
This driver does not work on all machines. In particular, early CATS
boards have hardware problems that will cause the machine to simply
lock up if the watchdog fires.
"If in doubt, leave it out" - say N.
config 977_WATCHDOG
tristate "NetWinder WB83C977 watchdog"
depends on (FOOTBRIDGE && ARCH_NETWINDER) || (ARM && COMPILE_TEST)
depends on HAS_IOPORT
help
Say Y here to include support for the WB977 watchdog included in
NetWinder machines. Alternatively say M to compile the driver as
a module, which will be called wdt977.
Not sure? It's safe to say N.
config FTWDT010_WATCHDOG
tristate "Faraday Technology FTWDT010 watchdog"
depends on ARM || COMPILE_TEST
select WATCHDOG_CORE
default ARCH_GEMINI
help
Say Y here if to include support for the Faraday Technology
FTWDT010 watchdog timer embedded in the Cortina Systems Gemini
family of devices.
To compile this driver as a module, choose M here: the
module will be called ftwdt010_wdt.
config IXP4XX_WATCHDOG
tristate "IXP4xx Watchdog"
depends on ARCH_IXP4XX || (ARM && COMPILE_TEST)
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
in the Intel IXP4xx network processors. This driver can
be built as a module by choosing M. The module will
be called ixp4xx_wdt.
Note: The internal IXP4xx watchdog does a soft CPU reset
which doesn't reset any peripherals. There are circumstances
where the watchdog will fail to reset the board correctly
(e.g., if the boot ROM is in an unreadable state).
Say N if you are unsure.
config S3C2410_WATCHDOG
tristate "S3C6410/S5Pv210/Exynos Watchdog"
depends on ARCH_S3C64XX || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
select WATCHDOG_CORE
help
Watchdog timer block in the Samsung S3C64xx, S5Pv210 and Exynos
SoCs. This will reboot the system when the timer expires with
the watchdog enabled.
The driver is limited by the speed of the system's PCLK
signal, so with reasonably fast systems (PCLK around 50-66MHz)
then watchdog intervals of over approximately 20seconds are
unavailable.
Choose Y/M here only if you build for such Samsung SoC.
The driver can be built as a module by choosing M, and will
be called s3c2410_wdt.
config SA1100_WATCHDOG
tristate "SA1100/PXA2xx watchdog"
depends on ARCH_SA1100 || ARCH_PXA || COMPILE_TEST
help
Watchdog timer embedded into SA11x0 and PXA2xx chips. This will
reboot your system when timeout is reached.
NOTE: once enabled, this timer cannot be disabled.
To compile this driver as a module, choose M here: the
module will be called sa1100_wdt.
config DW_WATCHDOG
tristate "Synopsys DesignWare watchdog"
depends on HAS_IOMEM
select WATCHDOG_CORE
help
Say Y here if to include support for the Synopsys DesignWare
watchdog timer found in many chips.
To compile this driver as a module, choose M here: the
module will be called dw_wdt.
config EP93XX_WATCHDOG
tristate "EP93xx Watchdog"
depends on ARCH_EP93XX || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
embedded in the Cirrus Logic EP93xx family of devices.
To compile this driver as a module, choose M here: the
module will be called ep93xx_wdt.
config OMAP_WATCHDOG
tristate "OMAP Watchdog"
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS || COMPILE_TEST
select WATCHDOG_CORE
help
Support for TI OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog.
Say 'Y' here to enable the
OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog timer.
config PNX4008_WATCHDOG
tristate "LPC32XX Watchdog"
depends on ARCH_LPC32XX || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
in the LPC32XX processor.
This driver can be built as a module by choosing M. The module
will be called pnx4008_wdt.
Say N if you are unsure.
config DAVINCI_WATCHDOG
tristate "DaVinci watchdog"
depends on ARCH_DAVINCI || ARCH_KEYSTONE || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
in the DaVinci DM644x/DM646x or Keystone processors.
To compile this driver as a module, choose M here: the
module will be called davinci_wdt.
NOTE: once enabled, this timer cannot be disabled.
Say N if you are unsure.
config K3_RTI_WATCHDOG
tristate "Texas Instruments K3 RTI watchdog"
depends on ARCH_K3 || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here if you want to include support for the K3 watchdog
timer (RTI module) available in the K3 generation of processors.
config ORION_WATCHDOG
tristate "Orion watchdog"
depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU || COMPILE_TEST
depends on ARM
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
in the Marvell Orion5x and Kirkwood ARM SoCs.
To compile this driver as a module, choose M here: the
module will be called orion_wdt.
config RN5T618_WATCHDOG
tristate "Ricoh RN5T618 watchdog"
depends on MFD_RN5T618 || COMPILE_TEST
select WATCHDOG_CORE
help
If you say yes here you get support for watchdog on the Ricoh
RN5T618 PMIC.
This driver can also be built as a module. If so, the module
will be called rn5t618_wdt.
config SUNXI_WATCHDOG
tristate "Allwinner SoCs watchdog support"
depends on ARCH_SUNXI || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Allwinner SoCs.
To compile this driver as a module, choose M here: the
module will be called sunxi_wdt.
config NPCM7XX_WATCHDOG
tristate "Nuvoton NPCM750 watchdog"
depends on ARCH_NPCM || COMPILE_TEST
default y if ARCH_NPCM7XX
select WATCHDOG_CORE
help
Say Y here to include Watchdog timer support for the
watchdog embedded into the NPCM7xx.
This watchdog is used to reset the system and thus cannot be
compiled as a module.
config TWL4030_WATCHDOG
tristate "TWL4030 Watchdog"
depends on TWL4030_CORE
select WATCHDOG_CORE
help
Support for TI TWL4030 watchdog. Say 'Y' here to enable the
watchdog timer support for TWL4030 chips.
config STMP3XXX_RTC_WATCHDOG
tristate "Freescale STMP3XXX & i.MX23/28 watchdog"
depends on RTC_DRV_STMP || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer inside
the RTC for the STMP37XX/378X or i.MX23/28 SoC.
To compile this driver as a module, choose M here: the
module will be called stmp3xxx_rtc_wdt.
config TS4800_WATCHDOG
tristate "TS-4800 Watchdog"
depends on HAS_IOMEM && OF
depends on SOC_IMX51 || COMPILE_TEST
select WATCHDOG_CORE
select MFD_SYSCON
help
Technologic Systems TS-4800 has watchdog timer implemented in
an external FPGA. Say Y here if you want to support for the
watchdog timer on TS-4800 board.
config TS72XX_WATCHDOG
tristate "TS-72XX SBC Watchdog"
depends on MACH_TS72XX || COMPILE_TEST
select WATCHDOG_CORE
help
Technologic Systems TS-7200, TS-7250 and TS-7260 boards have
watchdog timer implemented in a external CPLD chip. Say Y here
if you want to support for the watchdog timer on TS-72XX boards.
To compile this driver as a module, choose M here: the
module will be called ts72xx_wdt.
config MAX63XX_WATCHDOG
tristate "Max63xx watchdog"
depends on HAS_IOMEM
select WATCHDOG_CORE
help
Support for memory mapped max63{69,70,71,72,73,74} watchdog timer.
config MAX77620_WATCHDOG
tristate "Maxim Max77620 Watchdog Timer"
depends on MFD_MAX77620 || MFD_MAX77714 || COMPILE_TEST
select WATCHDOG_CORE
help
This is the driver for the Max77620 watchdog timer.
Say 'Y' here to enable the watchdog timer support for
MAX77620 chips. To compile this driver as a module,
choose M here: the module will be called max77620_wdt.
config IMX2_WDT
tristate "IMX2+ Watchdog"
depends on ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST
select REGMAP_MMIO
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog
on the Freescale IMX2 and later processors.
If you have one of these processors and wish to have
watchdog support enabled, say Y, otherwise say N.
To compile this driver as a module, choose M here: the
module will be called imx2_wdt.
config IMX_SC_WDT
tristate "IMX SC Watchdog"
depends on HAVE_ARM_SMCCC
depends on IMX_SCU || COMPILE_TEST
select WATCHDOG_CORE
help
This is the driver for the system controller watchdog
on the NXP i.MX SoCs with system controller inside, the
watchdog driver will call ARM SMC API and trap into
ARM-Trusted-Firmware for operations, ARM-Trusted-Firmware
will request system controller to execute the operations.
If you have one of these processors and wish to have
watchdog support enabled, say Y, otherwise say N.
To compile this driver as a module, choose M here: the
module will be called imx_sc_wdt.
config IMX7ULP_WDT
tristate "IMX7ULP Watchdog"
depends on ARCH_MXC || COMPILE_TEST
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog on the Freescale
IMX7ULP and later processors. If you have one of these
processors and wish to have watchdog support enabled,
say Y, otherwise say N.
To compile this driver as a module, choose M here: the
module will be called imx7ulp_wdt.
config DB500_WATCHDOG
tristate "ST-Ericsson DB800 watchdog"
depends on MFD_DB8500_PRCMU
select WATCHDOG_CORE
default y
help
Say Y here to include Watchdog timer support for the watchdog
existing in the prcmu of ST-Ericsson DB8500 platform.
To compile this driver as a module, choose M here: the
module will be called db500_wdt.
config RETU_WATCHDOG
tristate "Retu watchdog"
depends on MFD_RETU
select WATCHDOG_CORE
help
Retu watchdog driver for Nokia Internet Tablets (770, N800,
N810). At least on N800 the watchdog cannot be disabled, so
this driver is essential and you should enable it.
To compile this driver as a module, choose M here: the
module will be called retu_wdt.
config MOXART_WDT
tristate "MOXART watchdog"
depends on ARCH_MOXART || COMPILE_TEST
help
Say Y here to include Watchdog timer support for the watchdog
existing on the MOXA ART SoC series platforms.
To compile this driver as a module, choose M here: the
module will be called moxart_wdt.
config ST_LPC_WATCHDOG
tristate "STMicroelectronics LPC Watchdog"
depends on ARCH_STI || COMPILE_TEST
depends on OF
select WATCHDOG_CORE
help
Say Y here to include STMicroelectronics Low Power Controller
(LPC) based Watchdog timer support.
To compile this driver as a module, choose M here: the
module will be called st_lpc_wdt.
config TEGRA_WATCHDOG
tristate "Tegra watchdog"
depends on (ARCH_TEGRA || COMPILE_TEST) && HAS_IOMEM
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
embedded in NVIDIA Tegra SoCs.
To compile this driver as a module, choose M here: the
module will be called tegra_wdt.
config QCOM_WDT
tristate "QCOM watchdog"
depends on HAS_IOMEM
depends on ARCH_QCOM || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include Watchdog timer support for the watchdog found
on QCOM chipsets. Currently supported targets are the MSM8960,
APQ8064, and IPQ8064.
To compile this driver as a module, choose M here: the
module will be called qcom_wdt.
config MESON_GXBB_WATCHDOG
tristate "Amlogic Meson GXBB SoCs watchdog support"
depends on ARCH_MESON || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Amlogic Meson GXBB SoCs.
To compile this driver as a module, choose M here: the
module will be called meson_gxbb_wdt.
config MESON_WATCHDOG
tristate "Amlogic Meson SoCs watchdog support"
depends on ARCH_MESON || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Amlogic Meson SoCs.
To compile this driver as a module, choose M here: the
module will be called meson_wdt.
config MEDIATEK_WATCHDOG
tristate "Mediatek SoCs watchdog support"
depends on ARCH_MEDIATEK || COMPILE_TEST
default ARCH_MEDIATEK
select WATCHDOG_CORE
select RESET_CONTROLLER
help
Say Y here to include support for the watchdog timer
in Mediatek SoCs.
To compile this driver as a module, choose M here: the
module will be called mtk_wdt.
config DIGICOLOR_WATCHDOG
tristate "Conexant Digicolor SoCs watchdog support"
depends on ARCH_DIGICOLOR || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Conexant Digicolor SoCs.
To compile this driver as a module, choose M here: the
module will be called digicolor_wdt.
config ARM_SMC_WATCHDOG
tristate "ARM Secure Monitor Call based watchdog support"
depends on ARM || ARM64
depends on OF
depends on HAVE_ARM_SMCCC
select WATCHDOG_CORE
help
Say Y here to include support for a watchdog timer
implemented by the EL3 Secure Monitor on ARM platforms.
Requires firmware support.
To compile this driver as a module, choose M here: the
module will be called arm_smc_wdt.
config LPC18XX_WATCHDOG
tristate "LPC18xx/43xx Watchdog"
depends on ARCH_LPC18XX || COMPILE_TEST
depends on HAS_IOMEM
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
in NXP LPC SoCs family, which includes LPC18xx/LPC43xx
processors.
To compile this driver as a module, choose M here: the
module will be called lpc18xx_wdt.
config RENESAS_WDT
tristate "Renesas WDT Watchdog"
depends on ARCH_RENESAS || COMPILE_TEST
select WATCHDOG_CORE
help
This driver adds watchdog support for the integrated watchdogs in the
Renesas R-Car and other SH-Mobile SoCs (usually named RWDT or SWDT).
config RENESAS_RZAWDT
tristate "Renesas RZ/A WDT Watchdog"
depends on ARCH_RENESAS || COMPILE_TEST
select WATCHDOG_CORE
help
This driver adds watchdog support for the integrated watchdogs in the
Renesas RZ/A SoCs. These watchdogs can be used to reset a system.
config RENESAS_RZN1WDT
tristate "Renesas RZ/N1 watchdog"
depends on ARCH_RENESAS || COMPILE_TEST
select WATCHDOG_CORE
help
This driver adds watchdog support for the integrated watchdogs in the
Renesas RZ/N1 SoCs. These watchdogs can be used to reset a system.
config RENESAS_RZG2LWDT
tristate "Renesas RZ/G2L WDT Watchdog"
depends on ARCH_RZG2L || ARCH_R9A09G011 || COMPILE_TEST
depends on PM || COMPILE_TEST
select WATCHDOG_CORE
help
This driver adds watchdog support for the integrated watchdogs in the
Renesas RZ/G2L SoCs. These watchdogs can be used to reset a system.
config ASPEED_WATCHDOG
tristate "Aspeed BMC watchdog support"
depends on ARCH_ASPEED || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Aspeed BMC SoCs.
This driver is required to reboot the SoC.
To compile this driver as a module, choose M here: the
module will be called aspeed_wdt.
config STM32_WATCHDOG
tristate "STM32 Independent WatchDoG (IWDG) support"
depends on ARCH_STM32 || COMPILE_TEST
select WATCHDOG_CORE
default y
help
Say Y here to include support for the watchdog timer
in stm32 SoCs.
To compile this driver as a module, choose M here: the
module will be called stm32_iwdg.
config STPMIC1_WATCHDOG
tristate "STPMIC1 PMIC watchdog support"
depends on MFD_STPMIC1
select WATCHDOG_CORE
help
Say Y here to include watchdog support embedded into STPMIC1 PMIC.
If the watchdog timer expires, stpmic1 will shut down all its power
supplies.
To compile this driver as a module, choose M here: the
module will be called spmic1_wdt.
config UNIPHIER_WATCHDOG
tristate "UniPhier watchdog support"
depends on ARCH_UNIPHIER || COMPILE_TEST
depends on OF && MFD_SYSCON
select WATCHDOG_CORE
help
Say Y here to include support watchdog timer embedded
into the UniPhier system.
To compile this driver as a module, choose M here: the
module will be called uniphier_wdt.
config RTD119X_WATCHDOG
bool "Realtek RTD119x/RTD129x watchdog support"
depends on ARCH_REALTEK || COMPILE_TEST
depends on OF
select WATCHDOG_CORE
default ARCH_REALTEK
help
Say Y here to include support for the watchdog timer in
Realtek RTD1295 SoCs.
config REALTEK_OTTO_WDT
tristate "Realtek Otto MIPS watchdog support"
depends on MACH_REALTEK_RTL || COMPILE_TEST
depends on COMMON_CLK
select WATCHDOG_CORE
default MACH_REALTEK_RTL
help
Say Y here to include support for the watchdog timer on Realtek
RTL838x, RTL839x, RTL930x SoCs. This watchdog has pretimeout
notifications and system reset on timeout.
When built as a module this will be called realtek_otto_wdt.
config SPRD_WATCHDOG
tristate "Spreadtrum watchdog support"
depends on ARCH_SPRD || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include watchdog timer supported
by Spreadtrum system.
config PM8916_WATCHDOG
tristate "QCOM PM8916 pmic watchdog"
depends on OF && MFD_SPMI_PMIC
select WATCHDOG_CORE
help
Say Y here to include support watchdog timer embedded into the
pm8916 module.
config VISCONTI_WATCHDOG
tristate "Toshiba Visconti series watchdog support"
depends on ARCH_VISCONTI || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer in Toshiba
Visconti SoCs.
config MSC313E_WATCHDOG
tristate "MStar MSC313e watchdog"
depends on ARCH_MSTARV7 || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the Watchdog timer embedded
into MStar MSC313e chips. This will reboot your system when the
timeout is reached.
To compile this driver as a module, choose M here: the
module will be called msc313e_wdt.
config APPLE_WATCHDOG
tristate "Apple SoC watchdog"
depends on ARCH_APPLE || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the Watchdog found in Apple
SoCs such as the M1. Next to the common watchdog features this
driver is also required in order to reboot these SoCs.
To compile this driver as a module, choose M here: the
module will be called apple_wdt.
config SUNPLUS_WATCHDOG
tristate "Sunplus watchdog support"
depends on ARCH_SUNPLUS || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in Sunplus SoCs.
To compile this driver as a module, choose M here: the
module will be called sunplus_wdt.
# X86 (i386 + ia64 + x86_64) Architecture
config ACQUIRE_WDT
tristate "Acquire SBC Watchdog Timer"
depends on X86
help
This is the driver for the hardware watchdog on Single Board
Computers produced by Acquire Inc (and others). This watchdog
simply watches your kernel to make sure it doesn't freeze, and if
it does, it reboots your computer after a certain amount of time.
To compile this driver as a module, choose M here: the
module will be called acquirewdt.
Most people will say N.
config ADVANTECH_WDT
tristate "Advantech SBC Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
If you are configuring a Linux kernel for the Advantech single-board
computer, say `Y' here to support its built-in watchdog timer
feature. More information can be found at
<https://www.advantech.com.tw/products/>
config ADVANTECH_EC_WDT
tristate "Advantech Embedded Controller Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select ISA_BUS_API
select WATCHDOG_CORE
help
This driver supports Advantech products with ITE based Embedded Controller.
It does not support Advantech products with other ECs or without EC.
config ALIM1535_WDT
tristate "ALi M1535 PMU Watchdog Timer"
depends on (X86 || COMPILE_TEST) && PCI
help
This is the driver for the hardware watchdog on the ALi M1535 PMU.
To compile this driver as a module, choose M here: the
module will be called alim1535_wdt.
Most people will say N.
config ALIM7101_WDT
tristate "ALi M7101 PMU Computer Watchdog"
depends on PCI
help
This is the driver for the hardware watchdog on the ALi M7101 PMU
as used in the x86 Cobalt servers and also found in some
SPARC Netra servers too.
To compile this driver as a module, choose M here: the
module will be called alim7101_wdt.
Most people will say N.
config EBC_C384_WDT
tristate "WinSystems EBC-C384 Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select ISA_BUS_API
select WATCHDOG_CORE
help
Enables watchdog timer support for the watchdog timer on the
WinSystems EBC-C384 motherboard. The timeout may be configured via
the timeout module parameter.
config EXAR_WDT
tristate "Exar Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select WATCHDOG_CORE
help
Enables watchdog timer support for the watchdog timer present
in some Exar/MaxLinear UART chips like the XR28V38x.
To compile this driver as a module, choose M here: the
module will be called exar_wdt.
config F71808E_WDT
tristate "Fintek F718xx, F818xx Super I/O Watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog on the Fintek F71808E,
F71862FG, F71868, F71869, F71882FG, F71889FG, F81803, F81865, and
F81866 Super I/O controllers.
You can compile this driver directly into the kernel, or use
it as a module. The module will be called f71808e_wdt.
config SP5100_TCO
tristate "AMD/ATI SP5100 TCO Timer/Watchdog"
depends on (X86 || COMPILE_TEST) && PCI && HAS_IOPORT
select WATCHDOG_CORE
help
Hardware watchdog driver for the AMD/ATI SP5100 chipset. The TCO
(Total Cost of Ownership) timer is a watchdog timer that will reboot
the machine after its expiration. The expiration time can be
configured with the "heartbeat" parameter.
To compile this driver as a module, choose M here: the
module will be called sp5100_tco.
config GEODE_WDT
tristate "AMD Geode CS5535/CS5536 Watchdog"
depends on CS5535_MFGPT
help
This driver enables a watchdog capability built into the
CS5535/CS5536 companion chips for the AMD Geode GX and LX
processors. This watchdog watches your kernel to make sure
it doesn't freeze, and if it does, it reboots your computer after
a certain amount of time.
You can compile this driver directly into the kernel, or use
it as a module. The module will be called geodewdt.
config SC520_WDT
tristate "AMD Elan SC520 processor Watchdog"
depends on MELAN || COMPILE_TEST
help
This is the driver for the hardware watchdog built in to the
AMD "Elan" SC520 microcomputer commonly used in embedded systems.
This watchdog simply watches your kernel to make sure it doesn't
freeze, and if it does, it reboots your computer after a certain
amount of time.
You can compile this driver directly into the kernel, or use
it as a module. The module will be called sc520_wdt.
config SBC_FITPC2_WATCHDOG
tristate "Compulab SBC-FITPC2 watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the built-in watchdog timer on the fit-PC2,
fit-PC2i, CM-iAM single-board computers made by Compulab.
It's possible to enable the watchdog timer either from BIOS (F2) or
from booted Linux.
When the "Watchdog Timer Value" is enabled one can set 31-255 seconds
operational range.
Entering BIOS setup temporarily disables watchdog operation regardless
of current state, so system will not be restarted while user is in
BIOS setup.
Once the watchdog is enabled the system will be restarted every
"Watchdog Timer Value" period, so to prevent it user can restart or
disable the watchdog.
To compile this driver as a module, choose M here: the
module will be called sbc_fitpc2_wdt.
Most people will say N.
config EUROTECH_WDT
tristate "Eurotech CPU-1220/1410 Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
Enable support for the watchdog timer on the Eurotech CPU-1220 and
CPU-1410 cards. These are PC/104 SBCs. Spec sheets and product
information are at <http://www.eurotech.it/>.
config IB700_WDT
tristate "IB700 SBC Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog on the IB700 Single
Board Computer produced by TMC Technology (www.tmc-uk.com). This
watchdog simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of time.
This driver is like the WDT501 driver but for slightly different
hardware.
To compile this driver as a module, choose M here: the
module will be called ib700wdt.
Most people will say N.
config IBMASR
tristate "IBM Automatic Server Restart"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the IBM Automatic Server Restart watchdog
timer built-in into some eServer xSeries machines.
To compile this driver as a module, choose M here: the
module will be called ibmasr.
config WAFER_WDT
tristate "ICP Single Board Computer Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is a driver for the hardware watchdog on the ICP Single
Board Computer. This driver is working on (at least) the following
IPC SBC's: Wafer 5823, Rocky 4783, Rocky 3703 and Rocky 3782.
To compile this driver as a module, choose M here: the
module will be called wafer5823wdt.
config I6300ESB_WDT
tristate "Intel 6300ESB Timer/Watchdog"
depends on PCI
select WATCHDOG_CORE
help
Hardware driver for the watchdog timer built into the Intel
6300ESB controller hub.
To compile this driver as a module, choose M here: the
module will be called i6300esb.
config IE6XX_WDT
tristate "Intel Atom E6xx Watchdog"
depends on (X86 || COMPILE_TEST) && PCI && HAS_IOPORT
select WATCHDOG_CORE
select MFD_CORE
select LPC_SCH
help
Hardware driver for the watchdog timer built into the Intel
Atom E6XX (TunnelCreek) processor.
To compile this driver as a module, choose M here: the
module will be called ie6xx_wdt.
config INTEL_MID_WATCHDOG
tristate "Intel MID Watchdog Timer"
depends on X86_INTEL_MID
select WATCHDOG_CORE
help
Watchdog timer driver built into the Intel SCU for Intel MID
Platforms.
This driver currently supports only the watchdog evolution
implementation in SCU, available for Merrifield generation.
To compile this driver as a module, choose M here.
config ITCO_WDT
tristate "Intel TCO Timer/Watchdog"
depends on X86 && PCI
select WATCHDOG_CORE
depends on I2C || I2C=n
depends on MFD_INTEL_PMC_BXT || !MFD_INTEL_PMC_BXT
depends on HAS_IOPORT # for I2C_I801
select LPC_ICH if !EXPERT
select I2C_I801 if !EXPERT && I2C
help
Hardware driver for the intel TCO timer based watchdog devices.
These drivers are included in the Intel 82801 I/O Controller
Hub family (from ICH0 up to ICH10) and in the Intel 63xxESB
controller hub.
The TCO (Total Cost of Ownership) timer is a watchdog timer
that will reboot the machine after its second expiration. The
expiration time can be configured with the "heartbeat" parameter.
On some motherboards the driver may fail to reset the chipset's
NO_REBOOT flag which prevents the watchdog from rebooting the
machine. If this is the case you will get a kernel message like
"failed to reset NO_REBOOT flag, reboot disabled by hardware".
To compile this driver as a module, choose M here: the
module will be called iTCO_wdt.
config ITCO_VENDOR_SUPPORT
bool "Intel TCO Timer/Watchdog Specific Vendor Support"
depends on ITCO_WDT
help
Add vendor specific support to the intel TCO timer based watchdog
devices. At this moment we only have additional support for some
SuperMicro Inc. motherboards.
config IT8712F_WDT
tristate "IT8712F (Smart Guardian) Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the built-in watchdog timer on the IT8712F
Super I/0 chipset used on many motherboards.
If the driver does not work, then make sure that the game port in
the BIOS is enabled.
To compile this driver as a module, choose M here: the
module will be called it8712f_wdt.
config IT87_WDT
tristate "IT87 Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog on the ITE IT8607,
IT8620, IT8622, IT8625, IT8628, IT8655, IT8665, IT8686, IT8702,
IT8712, IT8716, IT8718, IT8720, IT8721, IT8726, IT8728, and
IT8783 Super I/O chips.
This watchdog simply watches your kernel to make sure it doesn't
freeze, and if it does, it reboots your computer after a certain
amount of time.
To compile this driver as a module, choose M here: the module will
be called it87_wdt.
config HP_WATCHDOG
tristate "HP ProLiant iLO2+ Hardware Watchdog Timer"
select WATCHDOG_CORE
depends on (ARM64 || X86 || COMPILE_TEST) && PCI
help
A software monitoring watchdog and NMI handling driver. This driver
will detect lockups and provide a stack trace. This is a driver that
will only load on an HP ProLiant system with a minimum of iLO2 support.
To compile this driver as a module, choose M here: the module will be
called hpwdt.
config HPWDT_NMI_DECODING
bool "NMI support for the HP ProLiant iLO2+ Hardware Watchdog Timer"
depends on X86 && HP_WATCHDOG
default y
help
Enables the NMI handler for the watchdog pretimeout NMI and the iLO
"Generate NMI to System" virtual button. When an NMI is claimed
by the driver, panic is called.
config KEMPLD_WDT
tristate "Kontron COM Watchdog Timer"
depends on MFD_KEMPLD
select WATCHDOG_CORE
help
Support for the PLD watchdog on some Kontron ETX and COMexpress
(ETXexpress) modules
This driver can also be built as a module. If so, the module will be
called kempld_wdt.
config SC1200_WDT
tristate "National Semiconductor PC87307/PC97307 (ala SC1200) Watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is a driver for National Semiconductor PC87307/PC97307 hardware
watchdog cards as found on the SC1200. This watchdog is mainly used
for power management purposes and can be used to power down the device
during inactivity periods (includes interrupt activity monitoring).
To compile this driver as a module, choose M here: the
module will be called sc1200wdt.
Most people will say N.
config SCx200_WDT
tristate "National Semiconductor SCx200 Watchdog"
depends on SCx200 && PCI
help
Enable the built-in watchdog timer support on the National
Semiconductor SCx200 processors.
If compiled as a module, it will be called scx200_wdt.
config PC87413_WDT
tristate "NS PC87413 watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog on the PC87413 chipset
This watchdog simply watches your kernel to make sure it doesn't
freeze, and if it does, it reboots your computer after a certain
amount of time.
To compile this driver as a module, choose M here: the
module will be called pc87413_wdt.
Most people will say N.
config NV_TCO
tristate "nVidia TCO Timer/Watchdog"
depends on (X86 || COMPILE_TEST) && PCI && HAS_IOPORT
help
Hardware driver for the TCO timer built into the nVidia Hub family
(such as the MCP51). The TCO (Total Cost of Ownership) timer is a
watchdog timer that will reboot the machine after its second
expiration. The expiration time can be configured with the
"heartbeat" parameter.
On some motherboards the driver may fail to reset the chipset's
NO_REBOOT flag which prevents the watchdog from rebooting the
machine. If this is the case you will get a kernel message like
"failed to reset NO_REBOOT flag, reboot disabled by hardware".
To compile this driver as a module, choose M here: the
module will be called nv_tco.
config RDC321X_WDT
tristate "RDC R-321x SoC watchdog"
depends on X86_RDC321X || COMPILE_TEST
depends on PCI
help
This is the driver for the built in hardware watchdog
in the RDC R-321x SoC.
To compile this driver as a module, choose M here: the
module will be called rdc321x_wdt.
config 60XX_WDT
tristate "SBC-60XX Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This driver can be used with the watchdog timer found on some
single board computers, namely the 6010 PII based computer.
It may well work with other cards. It reads port 0x443 to enable
and re-set the watchdog timer, and reads port 0x45 to disable
the watchdog. If you have a card that behave in similar ways,
you can probably make this driver work with your card as well.
You can compile this driver directly into the kernel, or use
it as a module. The module will be called sbc60xxwdt.
config SBC8360_WDT
tristate "SBC8360 Watchdog Timer"
depends on X86_32
help
This is the driver for the hardware watchdog on the SBC8360 Single
Board Computer produced by Axiomtek Co., Ltd. (www.axiomtek.com).
To compile this driver as a module, choose M here: the
module will be called sbc8360.
Most people will say N.
config SBC7240_WDT
tristate "SBC Nano 7240 Watchdog Timer"
depends on X86_32 && !UML
help
This is the driver for the hardware watchdog found on the IEI
single board computers EPIC Nano 7240 (and likely others). This
watchdog simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time.
To compile this driver as a module, choose M here: the
module will be called sbc7240_wdt.
config CPU5_WDT
tristate "SMA CPU5 Watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
TBD.
To compile this driver as a module, choose M here: the
module will be called cpu5wdt.
config SMSC_SCH311X_WDT
tristate "SMSC SCH311X Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog timer on the
SMSC SCH3112, SCH3114 and SCH3116 Super IO chipset
(LPC IO with 8042 KBC, Reset Generation, HWM and multiple
serial ports).
To compile this driver as a module, choose M here: the
module will be called sch311x_wdt.
config SMSC37B787_WDT
tristate "Winbond SMsC37B787 Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog component on the
Winbond SMsC37B787 chipset as used on the NetRunner Mainboard
from Vision Systems and maybe others.
This watchdog simply watches your kernel to make sure it doesn't
freeze, and if it does, it reboots your computer after a certain
amount of time.
Usually a userspace daemon will notify the kernel WDT driver that
userspace is still alive, at regular intervals.
To compile this driver as a module, choose M here: the
module will be called smsc37b787_wdt.
Most people will say N.
config TQMX86_WDT
tristate "TQ-Systems TQMX86 Watchdog Timer"
depends on X86 || COMPILE_TEST
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog timer in the TQMX86 IO
controller found on some of their ComExpress Modules.
To compile this driver as a module, choose M here; the module
will be called tqmx86_wdt.
Most people will say N.
config VIA_WDT
tristate "VIA Watchdog Timer"
depends on (X86 || COMPILE_TEST) && PCI
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog timer on VIA
southbridge chipset CX700, VX800/VX820 or VX855/VX875.
To compile this driver as a module, choose M here; the module
will be called via_wdt.
Most people will say N.
config W83627HF_WDT
tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
select WATCHDOG_CORE
help
This is the driver for the hardware watchdog on the following
Super I/O chips.
W83627DHG/DHG-P/EHF/EHG/F/G/HF/S/SF/THF/UHG/UG
W83637HF
W83667HG/HG-B
W83687THF
W83697HF
W83697UG
NCT6775
NCT6776
NCT6779
NCT6791
NCT6792
NCT6102D/04D/06D
NCT6116D
This watchdog simply watches your kernel to make sure it doesn't
freeze, and if it does, it reboots your computer after a certain
amount of time.
To compile this driver as a module, choose M here: the
module will be called w83627hf_wdt.
Most people will say N.
config W83877F_WDT
tristate "W83877F (EMACS) Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog on the W83877F chipset
as used in EMACS PC-104 motherboards (and likely others). This
watchdog simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time.
To compile this driver as a module, choose M here: the
module will be called w83877f_wdt.
Most people will say N.
config W83977F_WDT
tristate "W83977F (PCM-5335) Watchdog Timer"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the hardware watchdog on the W83977F I/O chip
as used in AAEON's PCM-5335 SBC (and likely others). This
watchdog simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time.
To compile this driver as a module, choose M here: the
module will be called w83977f_wdt.
config MACHZ_WDT
tristate "ZF MachZ Watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
If you are using a ZF Micro MachZ processor, say Y here, otherwise
N. This is the driver for the watchdog timer built-in on that
processor using ZF-Logic interface. This watchdog simply watches
your kernel to make sure it doesn't freeze, and if it does, it
reboots your computer after a certain amount of time.
To compile this driver as a module, choose M here: the
module will be called machzwd.
config SBC_EPX_C3_WATCHDOG
tristate "Winsystems SBC EPX-C3 watchdog"
depends on (X86 || COMPILE_TEST) && HAS_IOPORT
help
This is the driver for the built-in watchdog timer on the EPX-C3
Single-board computer made by Winsystems, Inc.
*Note*: This hardware watchdog is not probeable and thus there
is no way to know if writing to its IO address will corrupt
your system or have any real effect. The only way to be sure
that this driver does what you want is to make sure you
are running it on an EPX-C3 from Winsystems with the watchdog
timer at IO address 0x1ee and 0x1ef. It will write to both those
IO ports. Basically, the assumption is made that if you compile
this driver into your kernel and/or load it as a module, that you
know what you are doing and that you are in fact running on an
EPX-C3 board!
To compile this driver as a module, choose M here: the
module will be called sbc_epx_c3.
config INTEL_MEI_WDT
tristate "Intel MEI iAMT Watchdog"
depends on INTEL_MEI && X86
select WATCHDOG_CORE
help
A device driver for the Intel MEI iAMT watchdog.
The Intel AMT Watchdog is an OS Health (Hang/Crash) watchdog.
Whenever the OS hangs or crashes, iAMT will send an event
to any subscriber to this event. The watchdog doesn't reset the
the platform.
To compile this driver as a module, choose M here:
the module will be called mei_wdt.
config NI903X_WDT
tristate "NI 903x/913x Watchdog"
depends on X86 && ACPI
select WATCHDOG_CORE
help
This is the driver for the watchdog timer on the National Instruments
903x/913x real-time controllers.
To compile this driver as a module, choose M here: the module will be
called ni903x_wdt.
config NIC7018_WDT
tristate "NIC7018 Watchdog"
depends on X86 && ACPI
select WATCHDOG_CORE
help
Support for National Instruments NIC7018 Watchdog.
To compile this driver as a module, choose M here: the module will be
called nic7018_wdt.
config SIEMENS_SIMATIC_IPC_WDT
tristate "Siemens Simatic IPC Watchdog"
depends on SIEMENS_SIMATIC_IPC && PCI
default y
select WATCHDOG_CORE
select P2SB if X86
help
This driver adds support for several watchdogs found in Industrial
PCs from Siemens.
To compile this driver as a module, choose M here: the module will be
called simatic-ipc-wdt.
# M68K Architecture
config M54xx_WATCHDOG
tristate "MCF54xx watchdog support"
depends on M548x
help
To compile this driver as a module, choose M here: the
module will be called m54xx_wdt.
# MicroBlaze Architecture
# MIPS Architecture
config ATH79_WDT
tristate "Atheros AR71XX/AR724X/AR913X hardware watchdog"
depends on ATH79 || (ARM && COMPILE_TEST)
help
Hardware driver for the built-in watchdog timer on the Atheros
AR71XX/AR724X/AR913X SoCs.
config BCM47XX_WDT
tristate "Broadcom BCM47xx Watchdog Timer"
depends on BCM47XX || ARCH_BCM_5301X || COMPILE_TEST
select WATCHDOG_CORE
help
Hardware driver for the Broadcom BCM47xx Watchdog Timer.
config RC32434_WDT
tristate "IDT RC32434 SoC Watchdog Timer"
depends on MIKROTIK_RB532
help
Hardware driver for the IDT RC32434 SoC built-in
watchdog timer.
To compile this driver as a module, choose M here: the
module will be called rc32434_wdt.
config INDYDOG
tristate "Indy/I2 Hardware Watchdog"
depends on SGI_HAS_INDYDOG
help
Hardware driver for the Indy's/I2's watchdog. This is a
watchdog timer that will reboot the machine after a 60 second
timer expired and no process has written to /dev/watchdog during
that time.
config JZ4740_WDT
tristate "Ingenic jz4740 SoC hardware watchdog"
depends on MIPS || COMPILE_TEST
depends on COMMON_CLK
select WATCHDOG_CORE
select MFD_SYSCON
help
Hardware driver for the built-in watchdog timer on Ingenic jz4740 SoCs.
config WDT_MTX1
tristate "MTX-1 Hardware Watchdog"
depends on MIPS_MTX1 || (MIPS && COMPILE_TEST)
help
Hardware driver for the MTX-1 boards. This is a watchdog timer that
will reboot the machine after a 100 seconds timer expired.
config SIBYTE_WDOG
tristate "Sibyte SoC hardware watchdog"
depends on CPU_SB1
help
Watchdog driver for the built in watchdog hardware in Sibyte
SoC processors. There are apparently two watchdog timers
on such processors; this driver supports only the first one,
because currently Linux only supports exporting one watchdog
to userspace.
To compile this driver as a loadable module, choose M here.
The module will be called sb_wdog.
config TXX9_WDT
tristate "Toshiba TXx9 Watchdog Timer"
depends on CPU_TX49XX || (MIPS && COMPILE_TEST)
select WATCHDOG_CORE
help
Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
config OCTEON_WDT
tristate "Cavium OCTEON SOC family Watchdog Timer"
depends on CAVIUM_OCTEON_SOC
default y
select WATCHDOG_CORE
select EXPORT_UASM if OCTEON_WDT = m
help
Hardware driver for OCTEON's on chip watchdog timer.
Enables the watchdog for all cores running Linux. It
installs a NMI handler and pokes the watchdog based on an
interrupt. On first expiration of the watchdog, the
interrupt handler pokes it. The second expiration causes an
NMI that prints a message. The third expiration causes a
global soft reset.
When userspace has /dev/watchdog open, no poking is done
from the first interrupt, it is then only poked when the
device is written.
config MARVELL_GTI_WDT
tristate "Marvell GTI Watchdog driver"
depends on ARCH_THUNDER || (COMPILE_TEST && 64BIT)
default y
select WATCHDOG_CORE
help
Marvell GTI hardware supports watchdog timer. First timeout
works as watchdog pretimeout and installed interrupt handler
will be called on first timeout. Hardware can generate interrupt
to SCP on second timeout but it is not enabled, so second
timeout is ignored. If device poke does not happen then system
will reboot on third timeout.
config BCM2835_WDT
tristate "Broadcom BCM2835 hardware watchdog"
depends on ARCH_BCM2835 || (OF && COMPILE_TEST)
select WATCHDOG_CORE
help
Watchdog driver for the built in watchdog hardware in Broadcom
BCM2835 SoC.
To compile this driver as a loadable module, choose M here.
The module will be called bcm2835_wdt.
config BCM_KONA_WDT
tristate "BCM Kona Watchdog"
depends on ARCH_BCM_MOBILE || COMPILE_TEST
select WATCHDOG_CORE
help
Support for the watchdog timer on the following Broadcom BCM281xx
family, which includes BCM11130, BCM11140, BCM11351, BCM28145 and
BCM28155 variants.
Say 'Y' or 'M' here to enable the driver. The module will be called
bcm_kona_wdt.
config BCM_KONA_WDT_DEBUG
bool "DEBUGFS support for BCM Kona Watchdog"
depends on BCM_KONA_WDT || COMPILE_TEST
help
If enabled, adds /sys/kernel/debug/bcm_kona_wdt/info which provides
access to the driver's internal data structures as well as watchdog
timer hardware registres.
If in doubt, say 'N'.
config BCM7038_WDT
tristate "BCM63xx/BCM7038 Watchdog"
select WATCHDOG_CORE
depends on HAS_IOMEM
depends on ARCH_BCMBCA || ARCH_BRCMSTB || BMIPS_GENERIC || BCM63XX || COMPILE_TEST
help
Watchdog driver for the built-in hardware in Broadcom 7038 and
later SoCs used in set-top boxes. BCM7038 was made public
during the 2004 CES, and since then, many Broadcom chips use this
watchdog block, including some cable modem chips and DSL (63xx)
chips.
config IMGPDC_WDT
tristate "Imagination Technologies PDC Watchdog Timer"
depends on HAS_IOMEM
depends on MIPS || COMPILE_TEST
select WATCHDOG_CORE
help
Driver for Imagination Technologies PowerDown Controller
Watchdog Timer.
To compile this driver as a loadable module, choose M here.
The module will be called imgpdc_wdt.
config LANTIQ_WDT
tristate "Lantiq SoC watchdog"
depends on LANTIQ
select WATCHDOG_CORE
help
Hardware driver for the Lantiq SoC Watchdog Timer.
config LOONGSON1_WDT
tristate "Loongson1 SoC hardware watchdog"
depends on MACH_LOONGSON32 || COMPILE_TEST
select WATCHDOG_CORE
help
Hardware driver for the Loongson1 SoC Watchdog Timer.
config RALINK_WDT
tristate "Ralink SoC watchdog"
select WATCHDOG_CORE
depends on RALINK
help
Hardware driver for the Ralink SoC Watchdog Timer.
config GXP_WATCHDOG
tristate "HPE GXP watchdog support"
depends on ARCH_HPE_GXP || COMPILE_TEST
select WATCHDOG_CORE
help
Say Y here to include support for the watchdog timer
in HPE GXP SoCs.
To compile this driver as a module, choose M here.
The module will be called gxp-wdt.
config MT7621_WDT
tristate "Mediatek SoC watchdog"
select WATCHDOG_CORE
select REGMAP_MMIO
select MFD_SYSCON
depends on SOC_MT7620 || SOC_MT7621 || COMPILE_TEST
help
Hardware driver for the Mediatek/Ralink MT7621/8 SoC Watchdog Timer.
config PIC32_WDT
tristate "Microchip PIC32 hardware watchdog"
select WATCHDOG_CORE
depends on MACH_PIC32 || (MIPS && COMPILE_TEST)
help
Watchdog driver for the built in watchdog hardware in a PIC32.
Configuration bits must be set appropriately for the watchdog to be
controlled by this driver.
To compile this driver as a loadable module, choose M here.
The module will be called pic32-wdt.
config PIC32_DMT
tristate "Microchip PIC32 Deadman Timer"
select WATCHDOG_CORE
depends on MACH_PIC32 || (MIPS && COMPILE_TEST)
help
Watchdog driver for PIC32 instruction fetch counting timer. This
specific timer is typically be used in mission critical and safety
critical applications, where any single failure of the software
functionality and sequencing must be detected.
To compile this driver as a loadable module, choose M here.
The module will be called pic32-dmt.
# PARISC Architecture
# POWERPC Architecture
config GEF_WDT
tristate "GE Watchdog Timer"
depends on GE_FPGA
help
Watchdog timer found in a number of GE single board computers.
config MPC5200_WDT
bool "MPC52xx Watchdog Timer"
depends on PPC_MPC52xx || COMPILE_TEST
help
Use General Purpose Timer (GPT) 0 on the MPC5200 as Watchdog.
config 8xxx_WDT
tristate "MPC8xxx Platform Watchdog Timer"
depends on PPC_8xx || PPC_83xx || PPC_86xx || PPC_MPC512x
select WATCHDOG_CORE
help
This driver is for a SoC level watchdog that exists on some
Freescale PowerPC processors. So far this driver supports:
- MPC8xx watchdogs
- MPC83xx watchdogs
- MPC86xx watchdogs
For BookE processors (MPC85xx) use the BOOKE_WDT driver instead.
config PIKA_WDT
tristate "PIKA FPGA Watchdog"
depends on WARP || (PPC64 && COMPILE_TEST)
default y
help
This enables the watchdog in the PIKA FPGA. Currently used on
the Warp platform.
config BOOKE_WDT
tristate "PowerPC Book-E Watchdog Timer"
depends on BOOKE || 4xx
select WATCHDOG_CORE
help
Watchdog driver for PowerPC Book-E chips, such as the Freescale
MPC85xx SOCs and the IBM PowerPC 440.
Please see Documentation/watchdog/watchdog-api.rst for
more information.
config BOOKE_WDT_DEFAULT_TIMEOUT
int "PowerPC Book-E Watchdog Timer Default Timeout"
depends on BOOKE_WDT
default 38 if PPC_E500
range 0 63 if PPC_E500
default 3 if !PPC_E500
range 0 3 if !PPC_E500
help
Select the default watchdog timer period to be used by the PowerPC
Book-E watchdog driver. A watchdog "event" occurs when the bit
position represented by this number transitions from zero to one.
For Freescale Book-E processors, this is a number between 0 and 63.
For other Book-E processors, this is a number between 0 and 3.
The value can be overridden by the wdt_period command-line parameter.
config MEN_A21_WDT
tristate "MEN A21 VME CPU Carrier Board Watchdog Timer"
select WATCHDOG_CORE
depends on GPIOLIB || COMPILE_TEST
help
Watchdog driver for MEN A21 VMEbus CPU Carrier Boards.
The driver can also be built as a module. If so, the module will be
called mena21_wdt.
If unsure select N here.
# PPC64 Architecture
config PSERIES_WDT
tristate "POWER Architecture Platform Watchdog Timer"
depends on PPC_PSERIES
select WATCHDOG_CORE
help
Driver for virtual watchdog timers provided by PAPR
hypervisors (e.g. PowerVM, KVM).
config WATCHDOG_RTAS
tristate "RTAS watchdog"
depends on PPC_RTAS
help
This driver adds watchdog support for the RTAS watchdog.
To compile this driver as a module, choose M here. The module
will be called wdrtas.
# RISC-V Architecture
config STARFIVE_WATCHDOG
tristate "StarFive Watchdog support"
depends on ARCH_STARFIVE || COMPILE_TEST
select WATCHDOG_CORE
default ARCH_STARFIVE
help
Say Y here to support the watchdog of StarFive JH7100 and JH7110
SoC. This driver can also be built as a module if choose M.
# S390 Architecture
config DIAG288_WATCHDOG
tristate "System z diag288 Watchdog"
depends on S390
select WATCHDOG_CORE
help
IBM s/390 and zSeries machines running under z/VM 5.1 or later
provide a virtual watchdog timer to their guest that cause a
user define Control Program command to be executed after a
timeout.
LPAR provides a very similar interface. This driver handles
both.
To compile this driver as a module, choose M here. The module
will be called diag288_wdt.
# SUPERH (sh + sh64) Architecture
config SH_WDT
tristate "SuperH Watchdog"
depends on SUPERH && (CPU_SH3 || CPU_SH4 || COMPILE_TEST)
select WATCHDOG_CORE
help
This driver adds watchdog support for the integrated watchdog in the
SuperH processors. If you have one of these processors and wish
to have watchdog support enabled, say Y, otherwise say N.
As a side note, saying Y here will automatically boost HZ to 1000
so that the timer has a chance to clear the overflow counter. On
slower systems (such as the SH-2 and SH-3) this will likely yield
some performance issues. As such, the WDT should be avoided here
unless it is absolutely necessary.
To compile this driver as a module, choose M here: the
module will be called shwdt.
# SPARC Architecture
# SPARC64 Architecture
config WATCHDOG_CP1XXX
tristate "CP1XXX Hardware Watchdog support"
depends on SPARC64 && PCI
help
This is the driver for the hardware watchdog timers present on
Sun Microsystems CompactPCI models CP1400 and CP1500.
To compile this driver as a module, choose M here: the
module will be called cpwatchdog.
If you do not have a CompactPCI model CP1400 or CP1500, or
another UltraSPARC-IIi-cEngine boardset with hardware watchdog,
you should say N to this option.
config WATCHDOG_RIO
tristate "RIO Hardware Watchdog support"
depends on SPARC64 && PCI
help
Say Y here to support the hardware watchdog capability on Sun RIO
machines. The watchdog timeout period is normally one minute but
can be changed with a boot-time parameter.
config WATCHDOG_SUN4V
tristate "Sun4v Watchdog support"
select WATCHDOG_CORE
depends on SPARC64
help
Say Y here to support the hypervisor watchdog capability embedded
in the SPARC sun4v architecture.
To compile this driver as a module, choose M here. The module will
be called sun4v_wdt.
# XTENSA Architecture
# Xen Architecture
config XEN_WDT
tristate "Xen Watchdog support"
depends on XEN
select WATCHDOG_CORE
help
Say Y here to support the hypervisor watchdog capability provided
by Xen 4.0 and newer. The watchdog timeout period is normally one
minute but can be changed with a boot-time parameter.
config UML_WATCHDOG
tristate "UML watchdog"
depends on UML || COMPILE_TEST
#
# ISA-based Watchdog Cards
#
comment "ISA-based Watchdog Cards"
depends on ISA
config PCWATCHDOG
tristate "Berkshire Products ISA-PC Watchdog"
depends on ISA
help
This is the driver for the Berkshire Products ISA-PC Watchdog card.
This card simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time. This driver is like the WDT501 driver but for different
hardware. Please read <file:Documentation/watchdog/pcwd-watchdog.rst>.
The PC watchdog cards can be ordered from <http://www.berkprod.com/>.
To compile this driver as a module, choose M here: the
module will be called pcwd.
Most people will say N.
config MIXCOMWD
tristate "Mixcom Watchdog"
depends on ISA
help
This is a driver for the Mixcom hardware watchdog cards. This
watchdog simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time.
To compile this driver as a module, choose M here: the
module will be called mixcomwd.
Most people will say N.
config WDT
tristate "WDT Watchdog timer"
depends on ISA
help
If you have a WDT500P or WDT501P watchdog board, say Y here,
otherwise N. It is not possible to probe for this board, which means
that you have to inform the kernel about the IO port and IRQ that
is needed (you can do this via the io and irq parameters)
To compile this driver as a module, choose M here: the
module will be called wdt.
#
# PCI-based Watchdog Cards
#
comment "PCI-based Watchdog Cards"
depends on PCI
config PCIPCWATCHDOG
tristate "Berkshire Products PCI-PC Watchdog"
depends on PCI && HAS_IOPORT
help
This is the driver for the Berkshire Products PCI-PC Watchdog card.
This card simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time. The card can also monitor the internal temperature of the PC.
More info is available at <http://www.berkprod.com/pci_pc_watchdog.htm>.
To compile this driver as a module, choose M here: the
module will be called pcwd_pci.
Most people will say N.
config WDTPCI
tristate "PCI-WDT500/501 Watchdog timer"
depends on PCI && HAS_IOPORT
help
If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N.
If you have a PCI-WDT501 watchdog board then you can enable the
temperature sensor by setting the type parameter to 501.
If you want to enable the Fan Tachometer on the PCI-WDT501, then you
can do this via the tachometer parameter. Only do this if you have a
fan tachometer actually set up.
To compile this driver as a module, choose M here: the
module will be called wdt_pci.
#
# USB-based Watchdog Cards
#
comment "USB-based Watchdog Cards"
depends on USB
config USBPCWATCHDOG
tristate "Berkshire Products USB-PC Watchdog"
depends on USB
help
This is the driver for the Berkshire Products USB-PC Watchdog card.
This card simply watches your kernel to make sure it doesn't freeze,
and if it does, it reboots your computer after a certain amount of
time. The card can also monitor the internal temperature of the PC.
More info is available at <http://www.berkprod.com/usb_pc_watchdog.htm>.
To compile this driver as a module, choose M here: the
module will be called pcwd_usb.
Most people will say N.
config KEEMBAY_WATCHDOG
tristate "Intel Keem Bay SoC non-secure watchdog"
depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST)
select WATCHDOG_CORE
help
This option enable support for an In-secure watchdog timer driver for
Intel Keem Bay SoC. This WDT has a 32 bit timer and decrements in every
count unit. An interrupt will be triggered, when the count crosses
the threshold configured in the register.
To compile this driver as a module, choose M here: the
module will be called keembay_wdt.
endif # WATCHDOG
Codebase Browser
linux