.. SPDX-License-Identifier: GPL-2.0+
=====================================================
Linux Driver for Intel(R) Ethernet Network Connection
=====================================================
Intel Gigabit Linux driver.
Copyright(c) 2008-2018 Intel Corporation.
Contents
========
- Identifying Your Adapter
- Command Line Parameters
- Additional Configurations
- Support
Identifying Your Adapter
========================
For information on how to identify your adapter, and for the latest Intel
network drivers, refer to the Intel Support website:
https://www.intel.com/support
Command Line Parameters
=======================
If the driver is built as a module, the following optional parameters are used
by entering them on the command line with the modprobe command using this
syntax::
modprobe e1000e [<option>=<VAL1>,<VAL2>,...]
There needs to be a <VAL#> for each network port in the system supported by
this driver. The values will be applied to each instance, in function order.
For example::
modprobe e1000e InterruptThrottleRate=16000,16000
In this case, there are two network ports supported by e1000e in the system.
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
NOTE: A descriptor describes a data buffer and attributes related to the data
buffer. This information is accessed by the hardware.
InterruptThrottleRate
---------------------
:Valid Range: 0,1,3,4,100-100000
:Default Value: 3
Interrupt Throttle Rate controls the number of interrupts each interrupt
vector can generate per second. Increasing ITR lowers latency at the cost of
increased CPU utilization, though it may help throughput in some circumstances.
Setting InterruptThrottleRate to a value greater or equal to 100
will program the adapter to send out a maximum of that many interrupts
per second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value for
all traffic types, but lacking in small packet performance and latency.
The hardware can handle many more small packets per second however, and
for this reason an adaptive interrupt moderation algorithm was implemented.
The driver has two adaptive modes (setting 1 or 3) in which
it dynamically adjusts the InterruptThrottleRate value based on the traffic
that it receives. After determining the type of incoming traffic in the last
timeframe, it will adjust the InterruptThrottleRate to an appropriate value
for that traffic.
The algorithm classifies the incoming traffic every interval into
classes. Once the class is determined, the InterruptThrottleRate value is
adjusted to suit that traffic type the best. There are three classes defined:
"Bulk traffic", for large amounts of packets of normal size; "Low latency",
for small amounts of traffic and/or a significant percentage of small
packets; and "Lowest latency", for almost completely small packets or
minimal traffic.
- 0: Off
Turns off any interrupt moderation and may improve small packet latency.
However, this is generally not suitable for bulk throughput traffic due
to the increased CPU utilization of the higher interrupt rate.
- 1: Dynamic mode
This mode attempts to moderate interrupts per vector while maintaining
very low latency. This can sometimes cause extra CPU utilization. If
planning on deploying e1000e in a latency sensitive environment, this
parameter should be considered.
- 3: Dynamic Conservative mode (default)
In dynamic conservative mode, the InterruptThrottleRate value is set to
4000 for traffic that falls in class "Bulk traffic". If traffic falls in
the "Low latency" or "Lowest latency" class, the InterruptThrottleRate is
increased stepwise to 20000. This default mode is suitable for most
applications.
- 4: Simplified Balancing mode
In simplified mode the interrupt rate is based on the ratio of TX and
RX traffic. If the bytes per second rate is approximately equal, the
interrupt rate will drop as low as 2000 interrupts per second. If the
traffic is mostly transmit or mostly receive, the interrupt rate could
be as high as 8000.
- 100-100000:
Setting InterruptThrottleRate to a value greater or equal to 100
will program the adapter to send at most that many interrupts per second,
even if more packets have come in. This reduces interrupt load on the
system and can lower CPU utilization under heavy load, but will increase
latency as packets are not processed as quickly.
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
RxAbsIntDelay parameters. In other words, minimizing the receive and/or
transmit absolute delays does not force the controller to generate more
interrupts than what the Interrupt Throttle Rate allows.
RxIntDelay
----------
:Valid Range: 0-65535 (0=off)
:Default Value: 0
This value delays the generation of receive interrupts in units of 1.024
microseconds. Receive interrupt reduction can improve CPU efficiency if
properly tuned for specific network traffic. Increasing this value adds extra
latency to frame reception and can end up decreasing the throughput of TCP
traffic. If the system is reporting dropped receives, this value may be set
too high, causing the driver to run out of available receive descriptors.
CAUTION: When setting RxIntDelay to a value other than 0, adapters may hang
(stop transmitting) under certain network conditions. If this occurs a NETDEV
WATCHDOG message is logged in the system event log. In addition, the
controller is automatically reset, restoring the network connection. To
eliminate the potential for the hang ensure that RxIntDelay is set to 0.
RxAbsIntDelay
-------------
:Valid Range: 0-65535 (0=off)
:Default Value: 8
This value, in units of 1.024 microseconds, limits the delay in which a
receive interrupt is generated. This value ensures that an interrupt is
generated after the initial packet is received within the set amount of time,
which is useful only if RxIntDelay is non-zero. Proper tuning, along with
RxIntDelay, may improve traffic throughput in specific network conditions.
TxIntDelay
----------
:Valid Range: 0-65535 (0=off)
:Default Value: 8
This value delays the generation of transmit interrupts in units of 1.024
microseconds. Transmit interrupt reduction can improve CPU efficiency if
properly tuned for specific network traffic. If the system is reporting
dropped transmits, this value may be set too high causing the driver to run
out of available transmit descriptors.
TxAbsIntDelay
-------------
:Valid Range: 0-65535 (0=off)
:Default Value: 32
This value, in units of 1.024 microseconds, limits the delay in which a
transmit interrupt is generated. It is useful only if TxIntDelay is non-zero.
It ensures that an interrupt is generated after the initial Packet is sent on
the wire within the set amount of time. Proper tuning, along with TxIntDelay,
may improve traffic throughput in specific network conditions.
copybreak
---------
:Valid Range: 0-xxxxxxx (0=off)
:Default Value: 256
The driver copies all packets below or equaling this size to a fresh receive
buffer before handing it up the stack.
This parameter differs from other parameters because it is a single (not 1,1,1
etc.) parameter applied to all driver instances and it is also available
during runtime at /sys/module/e1000e/parameters/copybreak.
To use copybreak, type::
modprobe e1000e.ko copybreak=128
SmartPowerDownEnable
--------------------
:Valid Range: 0,1
:Default Value: 0 (disabled)
Allows the PHY to turn off in lower power states. The user can turn off this
parameter in supported chipsets.
KumeranLockLoss
---------------
:Valid Range: 0,1
:Default Value: 1 (enabled)
This workaround skips resetting the PHY at shutdown for the initial silicon
releases of ICH8 systems.
IntMode
-------
:Valid Range: 0-2
:Default Value: 0
+-------+----------------+
| Value | Interrupt Mode |
+=======+================+
| 0 | Legacy |
+-------+----------------+
| 1 | MSI |
+-------+----------------+
| 2 | MSI-X |
+-------+----------------+
IntMode allows load time control over the type of interrupt registered for by
the driver. MSI-X is required for multiple queue support, and some kernels and
combinations of kernel .config options will force a lower level of interrupt
support.
This command will show different values for each type of interrupt::
cat /proc/interrupts
CrcStripping
------------
:Valid Range: 0,1
:Default Value: 1 (enabled)
Strip the CRC from received packets before sending up the network stack. If
you have a machine with a BMC enabled but cannot receive IPMI traffic after
loading or enabling the driver, try disabling this feature.
WriteProtectNVM
---------------
:Valid Range: 0,1
:Default Value: 1 (enabled)
If set to 1, configure the hardware to ignore all write/erase cycles to the
GbE region in the ICHx NVM (in order to prevent accidental corruption of the
NVM). This feature can be disabled by setting the parameter to 0 during initial
driver load.
NOTE: The machine must be power cycled (full off/on) when enabling NVM writes
via setting the parameter to zero. Once the NVM has been locked (via the
parameter at 1 when the driver loads) it cannot be unlocked except via power
cycle.
Debug
-----
:Valid Range: 0-16 (0=none,...,16=all)
:Default Value: 0
This parameter adjusts the level of debug messages displayed in the system logs.
Additional Features and Configurations
======================================
Jumbo Frames
------------
Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU)
to a value larger than the default value of 1500.
Use the ifconfig command to increase the MTU size. For example, enter the
following where <x> is the interface number::
ifconfig eth<x> mtu 9000 up
Alternatively, you can use the ip command as follows::
ip link set mtu 9000 dev eth<x>
ip link set up dev eth<x>
This setting is not saved across reboots. The setting change can be made
permanent by adding 'MTU=9000' to the file:
- For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x>
- For SLES: /etc/sysconfig/network/<config_file>
NOTE: The maximum MTU setting for Jumbo Frames is 8996. This value coincides
with the maximum Jumbo Frames size of 9018 bytes.
NOTE: Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
poor performance or loss of link.
NOTE: The following adapters limit Jumbo Frames sized packets to a maximum of
4088 bytes:
- Intel(R) 82578DM Gigabit Network Connection
- Intel(R) 82577LM Gigabit Network Connection
The following adapters do not support Jumbo Frames:
- Intel(R) PRO/1000 Gigabit Server Adapter
- Intel(R) PRO/1000 PM Network Connection
- Intel(R) 82562G 10/100 Network Connection
- Intel(R) 82562G-2 10/100 Network Connection
- Intel(R) 82562GT 10/100 Network Connection
- Intel(R) 82562GT-2 10/100 Network Connection
- Intel(R) 82562V 10/100 Network Connection
- Intel(R) 82562V-2 10/100 Network Connection
- Intel(R) 82566DC Gigabit Network Connection
- Intel(R) 82566DC-2 Gigabit Network Connection
- Intel(R) 82566DM Gigabit Network Connection
- Intel(R) 82566MC Gigabit Network Connection
- Intel(R) 82566MM Gigabit Network Connection
- Intel(R) 82567V-3 Gigabit Network Connection
- Intel(R) 82577LC Gigabit Network Connection
- Intel(R) 82578DC Gigabit Network Connection
NOTE: Jumbo Frames cannot be configured on an 82579-based Network device if
MACSec is enabled on the system.
ethtool
-------
The driver utilizes the ethtool interface for driver configuration and
diagnostics, as well as displaying statistical information. The latest ethtool
version is required for this functionality. Download it at:
https://www.kernel.org/pub/software/network/ethtool/
NOTE: When validating enable/disable tests on some parts (for example, 82578),
it is necessary to add a few seconds between tests when working with ethtool.
Speed and Duplex Configuration
------------------------------
In addressing speed and duplex configuration issues, you need to distinguish
between copper-based adapters and fiber-based adapters.
In the default mode, an Intel(R) Ethernet Network Adapter using copper
connections will attempt to auto-negotiate with its link partner to determine
the best setting. If the adapter cannot establish link with the link partner
using auto-negotiation, you may need to manually configure the adapter and link
partner to identical settings to establish link and pass packets. This should
only be needed when attempting to link with an older switch that does not
support auto-negotiation or one that has been forced to a specific speed or
duplex mode. Your link partner must match the setting you choose. 1 Gbps speeds
and higher cannot be forced. Use the autonegotiation advertising setting to
manually set devices for 1 Gbps and higher.
Speed, duplex, and autonegotiation advertising are configured through the
ethtool utility.
Caution: Only experienced network administrators should force speed and duplex
or change autonegotiation advertising manually. The settings at the switch must
always match the adapter settings. Adapter performance may suffer or your
adapter may not operate if you configure the adapter differently from your
switch.
An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
will not attempt to auto-negotiate with its link partner since those adapters
operate only in full duplex and only at their native speed.
Enabling Wake on LAN (WoL)
--------------------------
WoL is configured through the ethtool utility.
WoL will be enabled on the system during the next shut down or reboot. For
this driver version, in order to enable WoL, the e1000e driver must be loaded
prior to shutting down or suspending the system.
NOTE: Wake on LAN is only supported on port A for the following devices:
- Intel(R) PRO/1000 PT Dual Port Network Connection
- Intel(R) PRO/1000 PT Dual Port Server Connection
- Intel(R) PRO/1000 PT Dual Port Server Adapter
- Intel(R) PRO/1000 PF Dual Port Server Adapter
- Intel(R) PRO/1000 PT Quad Port Server Adapter
- Intel(R) Gigabit PT Quad Port Server ExpressModule
Support
=======
For general information, go to the Intel support website at:
https://www.intel.com/support/
If an issue is identified with the released source code on a supported kernel
with a supported adapter, email the specific information related to the issue
to [email protected].
Codebase Browser
linux