# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/mdio-mux-gpio.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Properties for an MDIO bus multiplexer/switch controlled by GPIO pins.
maintainers:
- Andrew Lunn <[email protected]>
description:
This is a special case of a MDIO bus multiplexer. One or more GPIO
lines are used to control which child bus is connected.
allOf:
- $ref: /schemas/net/mdio-mux.yaml#
properties:
compatible:
const: mdio-mux-gpio
gpios:
description:
List of GPIOs used to control the multiplexer, least significant bit first.
minItems: 1
maxItems: 32
required:
- compatible
- gpios
unevaluatedProperties: false
examples:
- |
/*
An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a
pair of GPIO lines. Child busses 2 and 3 populated with 4
PHYs each.
*/
mdio-mux {
compatible = "mdio-mux-gpio";
gpios = <&gpio1 3 0>, <&gpio1 4 0>;
mdio-parent-bus = <&smi1>;
#address-cells = <1>;
#size-cells = <0>;
mdio@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
ethernet-phy@1 {
reg = <1>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
ethernet-phy@2 {
reg = <2>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
ethernet-phy@3 {
reg = <3>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
ethernet-phy@4 {
reg = <4>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <10 8>; /* Pin 10, active low */
};
};
mdio@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
ethernet-phy@1 {
reg = <1>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
ethernet-phy@2 {
reg = <2>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
ethernet-phy@3 {
reg = <3>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
ethernet-phy@4 {
reg = <4>;
marvell,reg-init = <3 0x10 0 0x5777>,
<3 0x11 0 0x00aa>,
<3 0x12 0 0x4105>,
<3 0x13 0 0x0a60>;
interrupt-parent = <&gpio>;
interrupts = <12 8>; /* Pin 12, active low */
};
};
};
...
Codebase Browser
linux