linux/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso

/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
/**
 * DT Overlay for CPSW9G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
 * J784S4 EVM. The Add-On Ethernet Card has to be connected to ENET Expansion 1 slot on the
 * board.
 *
 * Product Datasheet: https://www.ti.com/lit/ug/spruj74/spruj74.pdf
 *
 * Link to QSGMII Daughtercard: https://www.ti.com/tool/J721EXENETXPANEVM
 *
 * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
 */

/dts-v1/;
/plugin/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/phy/phy-cadence.h>
#include <dt-bindings/phy/phy.h>

#include "k3-pinctrl.h"
#include "k3-serdes.h"

&{/} {
	aliases {
		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@5";
		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@6";
		ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@7";
		ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@8";
		ethernet5 = "/bus@100000/ethernet@c200000/ethernet-ports/port@1";
	};
};

&main_cpsw0 {
	status = "okay";
};

&main_cpsw0_port5 {
	phy-handle = <&cpsw9g_phy1>;
	phy-mode = "qsgmii";
	mac-address = [00 00 00 00 00 00];
	phys = <&cpsw0_phy_gmii_sel 5>, <&serdes2_qsgmii_link>;
	phy-names = "mac", "serdes";
	status = "okay";
};

&main_cpsw0_port6 {
	phy-handle = <&cpsw9g_phy2>;
	phy-mode = "qsgmii";
	mac-address = [00 00 00 00 00 00];
	phys = <&cpsw0_phy_gmii_sel 6>, <&serdes2_qsgmii_link>;
	phy-names = "mac", "serdes";
	status = "okay";
};

&main_cpsw0_port7 {
	phy-handle = <&cpsw9g_phy0>;
	phy-mode = "qsgmii";
	mac-address = [00 00 00 00 00 00];
	phys = <&cpsw0_phy_gmii_sel 7>, <&serdes2_qsgmii_link>;
	phy-names = "mac", "serdes";
	status = "okay";
};

&main_cpsw0_port8 {
	phy-handle = <&cpsw9g_phy3>;
	phy-mode = "qsgmii";
	mac-address = [00 00 00 00 00 00];
	phys = <&cpsw0_phy_gmii_sel 8>, <&serdes2_qsgmii_link>;
	phy-names = "mac", "serdes";
	status = "okay";
};

&main_cpsw0_mdio {
	pinctrl-names = "default";
	pinctrl-0 = <&mdio0_default_pins>;
	bus_freq = <1000000>;
	reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
	reset-post-delay-us = <120000>;
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";

	cpsw9g_phy0: ethernet-phy@16 {
		reg = <16>;
	};
	cpsw9g_phy1: ethernet-phy@17 {
		reg = <17>;
	};
	cpsw9g_phy2: ethernet-phy@18 {
		reg = <18>;
	};
	cpsw9g_phy3: ethernet-phy@19 {
		reg = <19>;
	};
};

&exp2 {
	/* Power-up ENET1 EXPANDER PHY. */
	qsgmii-line-hog {
		gpio-hog;
		gpios = <16 GPIO_ACTIVE_HIGH>;
		output-low;
	};

	/* Toggle MUX2 for MDIO lines */
	mux-sel-hog {
		gpio-hog;
		gpios = <13 GPIO_ACTIVE_HIGH>, <14 GPIO_ACTIVE_HIGH>, <15 GPIO_ACTIVE_HIGH>;
		output-high;
	};
};

&main_pmx0 {
	mdio0_default_pins: mdio0-default-pins {
		pinctrl-single,pins = <
			J784S4_IOPAD(0x05c, PIN_INPUT, 4) /* (AC36) MCASP2_AXR0.MDIO1_MDIO */
			J784S4_IOPAD(0x058, PIN_INPUT, 4) /* (AE37) MCASP2_AFSX.MDIO1_MDC */
		>;
	};
};

&serdes_ln_ctrl {
	idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
		      <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
		      <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
		      <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
		      <J784S4_SERDES2_LANE0_QSGMII_LANE5>, <J784S4_SERDES2_LANE1_QSGMII_LANE6>,
		      <J784S4_SERDES2_LANE2_QSGMII_LANE7>, <J784S4_SERDES2_LANE3_QSGMII_LANE8>;
};

&serdes_wiz2 {
	status = "okay";
};

&serdes2 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";
	serdes2_qsgmii_link: phy@0 {
		reg = <2>;
		cdns,num-lanes = <1>;
		#phy-cells = <0>;
		cdns,phy-type = <PHY_TYPE_QSGMII>;
		resets = <&serdes_wiz2 3>;
	};
};