/* SPDX-License-Identifier: GPL-2.0-or-later */ /* * Montage Technology M88DS3103/M88RS6000 demodulator driver * * Copyright (C) 2013 Antti Palosaari <[email protected]> */ #ifndef M88DS3103_H #define M88DS3103_H #include <linux/dvb/frontend.h> /* * I2C address * 0x68, */ /** * enum m88ds3103_ts_mode - TS connection mode * @M88DS3103_TS_SERIAL: TS output pin D0, normal * @M88DS3103_TS_SERIAL_D7: TS output pin D7 * @M88DS3103_TS_PARALLEL: TS Parallel mode * @M88DS3103_TS_CI: TS CI Mode */ enum m88ds3103_ts_mode { … }; /** * enum m88ds3103_clock_out * @M88DS3103_CLOCK_OUT_DISABLED: Clock output is disabled * @M88DS3103_CLOCK_OUT_ENABLED: Clock output is enabled with crystal * clock. * @M88DS3103_CLOCK_OUT_ENABLED_DIV2: Clock output is enabled with half * crystal clock. */ enum m88ds3103_clock_out { … }; /** * struct m88ds3103_platform_data - Platform data for the m88ds3103 driver * @clk: Clock frequency. * @i2c_wr_max: Max bytes I2C adapter can write at once. * @ts_mode: TS mode. * @ts_clk: TS clock (KHz). * @ts_clk_pol: TS clk polarity. 1-active at falling edge; 0-active at rising * edge. * @spec_inv: Input spectrum inversion. * @agc: AGC configuration. * @agc_inv: AGC polarity. * @clk_out: Clock output. * @envelope_mode: DiSEqC envelope mode. * @lnb_hv_pol: LNB H/V pin polarity. 0: pin high set to VOLTAGE_18, pin low to * set VOLTAGE_13. 1: pin high set to VOLTAGE_13, pin low to set VOLTAGE_18. * @lnb_en_pol: LNB enable pin polarity. 0: pin high to disable, pin low to * enable. 1: pin high to enable, pin low to disable. * @get_dvb_frontend: Get DVB frontend. * @get_i2c_adapter: Get I2C adapter. */ struct m88ds3103_platform_data { … }; /** * struct m88ds3103_config - m88ds3102 configuration * * @i2c_addr: I2C address. Default: none, must set. Example: 0x68, ... * @clock: Device's clock. Default: none, must set. Example: 27000000 * @i2c_wr_max: Max bytes I2C provider is asked to write at once. * Default: none, must set. Example: 33, 65, ... * @ts_mode: TS output mode, as defined by &enum m88ds3103_ts_mode. * Default: M88DS3103_TS_SERIAL. * @ts_clk: TS clk in KHz. Default: 0. * @ts_clk_pol: TS clk polarity.Default: 0. * 1-active at falling edge; 0-active at rising edge. * @spec_inv: Spectrum inversion. Default: 0. * @agc_inv: AGC polarity. Default: 0. * @clock_out: Clock output, as defined by &enum m88ds3103_clock_out. * Default: M88DS3103_CLOCK_OUT_DISABLED. * @envelope_mode: DiSEqC envelope mode. Default: 0. * @agc: AGC configuration. Default: none, must set. * @lnb_hv_pol: LNB H/V pin polarity. Default: 0. Values: * 1: pin high set to VOLTAGE_13, pin low to set VOLTAGE_18; * 0: pin high set to VOLTAGE_18, pin low to set VOLTAGE_13. * @lnb_en_pol: LNB enable pin polarity. Default: 0. Values: * 1: pin high to enable, pin low to disable; * 0: pin high to disable, pin low to enable. */ struct m88ds3103_config { … }; #if defined(CONFIG_DVB_M88DS3103) || \ (defined(CONFIG_DVB_M88DS3103_MODULE) && defined(MODULE)) /** * m88ds3103_attach - Attach a m88ds3103 demod * * @config: pointer to &struct m88ds3103_config with demod configuration. * @i2c: i2c adapter to use. * @tuner_i2c: on success, returns the I2C adapter associated with * m88ds3103 tuner. * * return: FE pointer on success, NULL on failure. * Note: Do not add new m88ds3103_attach() users! Use I2C bindings instead. */ extern struct dvb_frontend *m88ds3103_attach( const struct m88ds3103_config *config, struct i2c_adapter *i2c, struct i2c_adapter **tuner_i2c); extern int m88ds3103_get_agc_pwm(struct dvb_frontend *fe, u8 *_agc_pwm); #else static inline struct dvb_frontend *m88ds3103_attach( const struct m88ds3103_config *config, struct i2c_adapter *i2c, struct i2c_adapter **tuner_i2c) { pr_warn("%s: driver disabled by Kconfig\n", __func__); return NULL; } #define m88ds3103_get_agc_pwm … #endif #endif
Codebase Browser
linux