/* * Copyright (c) 2006, 2007, 2008, 2009 QLogic Corporation. All rights reserved. * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. * * This software is available to you under a choice of one of two * licenses. You may choose to be licensed under the terms of the GNU * General Public License (GPL) Version 2, available from the file * COPYING in the main directory of this source tree, or the * OpenIB.org BSD license below: * * Redistribution and use in source and binary forms, with or * without modification, are permitted provided that the following * conditions are met: * * - Redistributions of source code must retain the above * copyright notice, this list of conditions and the following * disclaimer. * * - Redistributions in binary form must reproduce the above * copyright notice, this list of conditions and the following * disclaimer in the documentation and/or other materials * provided with the distribution. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE * SOFTWARE. */ /* QSFP support common definitions, for ib_qib driver */ #define QSFP_DEV … #define QSFP_PWR_LAG_MSEC … #define QSFP_MODPRS_LAG_MSEC … /* * Below are masks for various QSFP signals, for Port 1. * Port2 equivalents are shifted by QSFP_GPIO_PORT2_SHIFT. * _N means asserted low */ #define QSFP_GPIO_MOD_SEL_N … #define QSFP_GPIO_MOD_PRS_N … #define QSFP_GPIO_INT_N … #define QSFP_GPIO_MOD_RST_N … #define QSFP_GPIO_LP_MODE … #define QSFP_GPIO_PORT2_SHIFT … #define QSFP_PAGESIZE … /* Defined fields that QLogic requires of qualified cables */ /* Byte 0 is Identifier, not checked */ /* Byte 1 is reserved "status MSB" */ /* Byte 2 is "status LSB" We only care that D2 "Flat Mem" is set. */ /* * Rest of first 128 not used, although 127 is reserved for page select * if module is not "Flat memory". */ /* Byte 128 is Identifier: must be 0x0c for QSFP, or 0x0d for QSFP+ */ #define QSFP_MOD_ID_OFFS … /* * Byte 129 is "Extended Identifier". We only care about D7,D6: Power class * 0:1.5W, 1:2.0W, 2:2.5W, 3:3.5W */ #define QSFP_MOD_PWR_OFFS … /* Byte 130 is Connector type. Not QLogic req'd */ /* Bytes 131..138 are Transceiver types, bit maps for various tech, none IB */ /* Byte 139 is encoding. code 0x01 is 8b10b. Not QLogic req'd */ /* byte 140 is nominal bit-rate, in units of 100Mbits/sec Not QLogic req'd */ /* Byte 141 is Extended Rate Select. Not QLogic req'd */ /* Bytes 142..145 are lengths for various fiber types. Not QLogic req'd */ /* Byte 146 is length for Copper. Units of 1 meter */ #define QSFP_MOD_LEN_OFFS … /* * Byte 147 is Device technology. D0..3 not Qlogc req'd * D4..7 select from 15 choices, translated by table: */ #define QSFP_MOD_TECH_OFFS … extern const char *const qib_qsfp_devtech[16]; /* Active Equalization includes fiber, copper full EQ, and copper near Eq */ #define QSFP_IS_ACTIVE(tech) … /* Active Equalization includes fiber, copper full EQ, and copper far Eq */ #define QSFP_IS_ACTIVE_FAR(tech) … /* Attenuation should be valid for copper other than full/near Eq */ #define QSFP_HAS_ATTEN(tech) … /* Length is only valid if technology is "copper" */ #define QSFP_IS_CU(tech) … #define QSFP_TECH_1490 … #define QSFP_OUI(oui) … #define QSFP_OUI_AMPHENOL … #define QSFP_OUI_FINISAR … #define QSFP_OUI_GORE … /* Bytes 148..163 are Vendor Name, Left-justified Blank-filled */ #define QSFP_VEND_OFFS … #define QSFP_VEND_LEN … /* Byte 164 is IB Extended tranceiver codes Bits D0..3 are SDR,DDR,QDR,EDR */ #define QSFP_IBXCV_OFFS … /* Bytes 165..167 are Vendor OUI number */ #define QSFP_VOUI_OFFS … #define QSFP_VOUI_LEN … /* Bytes 168..183 are Vendor Part Number, string */ #define QSFP_PN_OFFS … #define QSFP_PN_LEN … /* Bytes 184,185 are Vendor Rev. Left Justified, Blank-filled */ #define QSFP_REV_OFFS … #define QSFP_REV_LEN … /* * Bytes 186,187 are Wavelength, if Optical. Not Qlogic req'd * If copper, they are attenuation in dB: * Byte 186 is at 2.5Gb/sec (SDR), Byte 187 at 5.0Gb/sec (DDR) */ #define QSFP_ATTEN_OFFS … #define QSFP_ATTEN_LEN … /* Bytes 188,189 are Wavelength tolerance, not QLogic req'd */ /* Byte 190 is Max Case Temp. Not QLogic req'd */ /* Byte 191 is LSB of sum of bytes 128..190. Not QLogic req'd */ #define QSFP_CC_OFFS … /* Bytes 192..195 are Options implemented in qsfp. Not Qlogic req'd */ /* Bytes 196..211 are Serial Number, String */ #define QSFP_SN_OFFS … #define QSFP_SN_LEN … /* Bytes 212..219 are date-code YYMMDD (MM==1 for Jan) */ #define QSFP_DATE_OFFS … #define QSFP_DATE_LEN … /* Bytes 218,219 are optional lot-code, string */ #define QSFP_LOT_OFFS … #define QSFP_LOT_LEN … /* Bytes 220, 221 indicate monitoring options, Not QLogic req'd */ /* Byte 223 is LSB of sum of bytes 192..222 */ #define QSFP_CC_EXT_OFFS … /* * struct qib_qsfp_data encapsulates state of QSFP device for one port. * it will be part of port-chip-specific data if a board supports QSFP. * * Since multiple board-types use QSFP, and their pport_data structs * differ (in the chip-specific section), we need a pointer to its head. * * Avoiding premature optimization, we will have one work_struct per port, * and let the (increasingly inaccurately named) eep_lock arbitrate * access to common resources. * */ /* * Hold the parts of the onboard EEPROM that we care about, so we aren't * coonstantly bit-boffing */ struct qib_qsfp_cache { … }; #define QSFP_PWR(pbyte) … #define QSFP_ATTEN_SDR(attenarray) … #define QSFP_ATTEN_DDR(attenarray) … struct qib_qsfp_data { … }; extern int qib_refresh_qsfp_cache(struct qib_pportdata *ppd, struct qib_qsfp_cache *cp); extern int qib_qsfp_mod_present(struct qib_pportdata *ppd); extern void qib_qsfp_init(struct qib_qsfp_data *qd, void (*fevent)(struct work_struct *));
Codebase Browser
linux