/* SPDX-License-Identifier: GPL-2.0 */
/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
/* true: device connected */
#define PORT_CONNECT (1 << 0)
/* true: port enabled */
#define PORT_PE (1 << 1)
/* bit 2 reserved and zeroed */
/* true: port has an over-current condition */
#define PORT_OC (1 << 3)
/* true: port reset signaling asserted */
#define PORT_RESET (1 << 4)
/* Port Link State - bits 5:8
* A read gives the current link PM state of the port,
* a write with Link State Write Strobe set sets the link state.
*/
#define PORT_PLS_MASK (0xf << 5)
#define XDEV_U0 (0x0 << 5)
#define XDEV_U1 (0x1 << 5)
#define XDEV_U2 (0x2 << 5)
#define XDEV_U3 (0x3 << 5)
#define XDEV_DISABLED (0x4 << 5)
#define XDEV_RXDETECT (0x5 << 5)
#define XDEV_INACTIVE (0x6 << 5)
#define XDEV_POLLING (0x7 << 5)
#define XDEV_RECOVERY (0x8 << 5)
#define XDEV_HOT_RESET (0x9 << 5)
#define XDEV_COMP_MODE (0xa << 5)
#define XDEV_TEST_MODE (0xb << 5)
#define XDEV_RESUME (0xf << 5)
/* true: port has power (see HCC_PPC) */
#define PORT_POWER (1 << 9)
/* bits 10:13 indicate device speed:
* 0 - undefined speed - port hasn't be initialized by a reset yet
* 1 - full speed
* 2 - low speed
* 3 - high speed
* 4 - super speed
* 5-15 reserved
*/
#define DEV_SPEED_MASK (0xf << 10)
#define XDEV_FS (0x1 << 10)
#define XDEV_LS (0x2 << 10)
#define XDEV_HS (0x3 << 10)
#define XDEV_SS (0x4 << 10)
#define XDEV_SSP (0x5 << 10)
#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
/* Bits 20:23 in the Slot Context are the speed for the device */
#define SLOT_SPEED_FS (XDEV_FS << 10)
#define SLOT_SPEED_LS (XDEV_LS << 10)
#define SLOT_SPEED_HS (XDEV_HS << 10)
#define SLOT_SPEED_SS (XDEV_SS << 10)
#define SLOT_SPEED_SSP (XDEV_SSP << 10)
/* Port Indicator Control */
#define PORT_LED_OFF (0 << 14)
#define PORT_LED_AMBER (1 << 14)
#define PORT_LED_GREEN (2 << 14)
#define PORT_LED_MASK (3 << 14)
/* Port Link State Write Strobe - set this when changing link state */
#define PORT_LINK_STROBE (1 << 16)
/* true: connect status change */
#define PORT_CSC (1 << 17)
/* true: port enable change */
#define PORT_PEC (1 << 18)
/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
* into an enabled state, and the device into the default state. A "warm" reset
* also resets the link, forcing the device through the link training sequence.
* SW can also look at the Port Reset register to see when warm reset is done.
*/
#define PORT_WRC (1 << 19)
/* true: over-current change */
#define PORT_OCC (1 << 20)
/* true: reset change - 1 to 0 transition of PORT_RESET */
#define PORT_RC (1 << 21)
/* port link status change - set on some port link state transitions:
* Transition Reason
* ------------------------------------------------------------------------------
* - U3 to Resume Wakeup signaling from a device
* - Resume to Recovery to U0 USB 3.0 device resume
* - Resume to U0 USB 2.0 device resume
* - U3 to Recovery to U0 Software resume of USB 3.0 device complete
* - U3 to U0 Software resume of USB 2.0 device complete
* - U2 to U0 L1 resume of USB 2.1 device complete
* - U0 to U0 (???) L1 entry rejection by USB 2.1 device
* - U0 to disabled L1 entry error with USB 2.1 device
* - Any state to inactive Error on USB 3.0 port
*/
#define PORT_PLC (1 << 22)
/* port configure error change - port failed to configure its link partner */
#define PORT_CEC (1 << 23)
#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
PORT_RC | PORT_PLC | PORT_CEC)
/* Cold Attach Status - xHC can set this bit to report device attached during
* Sx state. Warm port reset should be perfomed to clear this bit and move port
* to connected state.
*/
#define PORT_CAS (1 << 24)
/* wake on connect (enable) */
#define PORT_WKCONN_E (1 << 25)
/* wake on disconnect (enable) */
#define PORT_WKDISC_E (1 << 26)
/* wake on over-current (enable) */
#define PORT_WKOC_E (1 << 27)
/* bits 28:29 reserved */
/* true: device is non-removable - for USB 3.0 roothub emulation */
#define PORT_DEV_REMOVE (1 << 30)
/* Initiate a warm port reset - complete when PORT_WRC is '1' */
#define PORT_WR (1 << 31)
/* We mark duplicate entries with -1 */
#define DUPLICATE_ENTRY ((u8)(-1))
/* Port Power Management Status and Control - port_power_base bitmasks */
/* Inactivity timer value for transitions into U1, in microseconds.
* Timeout can be up to 127us. 0xFF means an infinite timeout.
*/
#define PORT_U1_TIMEOUT(p) ((p) & 0xff)
#define PORT_U1_TIMEOUT_MASK 0xff
/* Inactivity timer value for transitions into U2 */
#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
#define PORT_U2_TIMEOUT_MASK (0xff << 8)
/* Bits 24:31 for port testing */
/* USB2 Protocol PORTSPMSC */
#define PORT_L1S_MASK 7
#define PORT_L1S_SUCCESS 1
#define PORT_RWE (1 << 3)
#define PORT_HIRD(p) (((p) & 0xf) << 4)
#define PORT_HIRD_MASK (0xf << 4)
#define PORT_L1DS_MASK (0xff << 8)
#define PORT_L1DS(p) (((p) & 0xff) << 8)
#define PORT_HLE (1 << 16)
#define PORT_TEST_MODE_SHIFT 28
/* USB3 Protocol PORTLI Port Link Information */
#define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
#define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
/* USB2 Protocol PORTHLPMC */
#define PORT_HIRDM(p)((p) & 3)
#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
#define PORT_BESLD(p)(((p) & 0xf) << 10)
/* use 512 microseconds as USB2 LPM L1 default timeout. */
#define XHCI_L1_TIMEOUT 512
/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
* Safe to use with mixed HIRD and BESL systems (host and device) and is used
* by other operating systems.
*
* XHCI 1.0 errata 8/14/12 Table 13 notes:
* "Software should choose xHC BESL/BESLD field values that do not violate a
* device's resume latency requirements,
* e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
* or not program values < '4' if BLC = '0' and a BESL device is attached.
*/
#define XHCI_DEFAULT_BESL 4
/*
* USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
* to complete link training. usually link trainig completes much faster
* so check status 10 times with 36ms sleep in places we need to wait for
* polling to complete.
*/
#define XHCI_PORT_POLLING_LFPS_TIME 36
Codebase Browser
linux