/* SPDX-License-Identifier: GPL-2.0-only */
/*
* Access to user system call parameters and results
*
* Copyright (C) 2008-2009 Red Hat, Inc. All rights reserved.
*
* This file is a stub providing documentation for what functions
* asm-ARCH/syscall.h files need to define. Most arch definitions
* will be simple inlines.
*
* All of these functions expect to be called with no locks,
* and only when the caller is sure that the task of interest
* cannot return to user mode while we are looking at it.
*/
#ifndef _ASM_SYSCALL_H
#define _ASM_SYSCALL_H 1
struct task_struct;
struct pt_regs;
/**
* syscall_get_nr - find what system call a task is executing
* @task: task of interest, must be blocked
* @regs: task_pt_regs() of @task
*
* If @task is executing a system call or is at system call
* tracing about to attempt one, returns the system call number.
* If @task is not executing a system call, i.e. it's blocked
* inside the kernel for a fault or signal, returns -1.
*
* Note this returns int even on 64-bit machines. Only 32 bits of
* system call number can be meaningful. If the actual arch value
* is 64 bits, this truncates to 32 bits so 0xffffffff means -1.
*
* It's only valid to call this when @task is known to be blocked.
*/
int syscall_get_nr(struct task_struct *task, struct pt_regs *regs);
/**
* syscall_rollback - roll back registers after an aborted system call
* @task: task of interest, must be in system call exit tracing
* @regs: task_pt_regs() of @task
*
* It's only valid to call this when @task is stopped for system
* call exit tracing (due to %SYSCALL_WORK_SYSCALL_TRACE or
* %SYSCALL_WORK_SYSCALL_AUDIT), after ptrace_report_syscall_entry()
* returned nonzero to prevent the system call from taking place.
*
* This rolls back the register state in @regs so it's as if the
* system call instruction was a no-op. The registers containing
* the system call number and arguments are as they were before the
* system call instruction. This may not be the same as what the
* register state looked like at system call entry tracing.
*/
void syscall_rollback(struct task_struct *task, struct pt_regs *regs);
/**
* syscall_get_error - check result of traced system call
* @task: task of interest, must be blocked
* @regs: task_pt_regs() of @task
*
* Returns 0 if the system call succeeded, or -ERRORCODE if it failed.
*
* It's only valid to call this when @task is stopped for tracing on exit
* from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
* %SYSCALL_WORK_SYSCALL_AUDIT.
*/
long syscall_get_error(struct task_struct *task, struct pt_regs *regs);
/**
* syscall_get_return_value - get the return value of a traced system call
* @task: task of interest, must be blocked
* @regs: task_pt_regs() of @task
*
* Returns the return value of the successful system call.
* This value is meaningless if syscall_get_error() returned nonzero.
*
* It's only valid to call this when @task is stopped for tracing on exit
* from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
* %SYSCALL_WORK_SYSCALL_AUDIT.
*/
long syscall_get_return_value(struct task_struct *task, struct pt_regs *regs);
/**
* syscall_set_return_value - change the return value of a traced system call
* @task: task of interest, must be blocked
* @regs: task_pt_regs() of @task
* @error: negative error code, or zero to indicate success
* @val: user return value if @error is zero
*
* This changes the results of the system call that user mode will see.
* If @error is zero, the user sees a successful system call with a
* return value of @val. If @error is nonzero, it's a negated errno
* code; the user sees a failed system call with this errno code.
*
* It's only valid to call this when @task is stopped for tracing on exit
* from a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
* %SYSCALL_WORK_SYSCALL_AUDIT.
*/
void syscall_set_return_value(struct task_struct *task, struct pt_regs *regs,
int error, long val);
/**
* syscall_get_arguments - extract system call parameter values
* @task: task of interest, must be blocked
* @regs: task_pt_regs() of @task
* @args: array filled with argument values
*
* Fetches 6 arguments to the system call. First argument is stored in
* @args[0], and so on.
*
* It's only valid to call this when @task is stopped for tracing on
* entry to a system call, due to %SYSCALL_WORK_SYSCALL_TRACE or
* %SYSCALL_WORK_SYSCALL_AUDIT.
*/
void syscall_get_arguments(struct task_struct *task, struct pt_regs *regs,
unsigned long *args);
/**
* syscall_get_arch - return the AUDIT_ARCH for the current system call
* @task: task of interest, must be blocked
*
* Returns the AUDIT_ARCH_* based on the system call convention in use.
*
* It's only valid to call this when @task is stopped on entry to a system
* call, due to %SYSCALL_WORK_SYSCALL_TRACE, %SYSCALL_WORK_SYSCALL_AUDIT, or
* %SYSCALL_WORK_SECCOMP.
*
* Architectures which permit CONFIG_HAVE_ARCH_SECCOMP_FILTER must
* provide an implementation of this.
*/
int syscall_get_arch(struct task_struct *task);
#endif /* _ASM_SYSCALL_H */
Codebase Browser
linux