// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2009,2010 One Laptop per Child
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/acpi.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/gpio/consumer.h>
#include <linux/gpio/machine.h>
#include <asm/olpc.h>
/* TODO: this eventually belongs in linux/vx855.h */
#define NR_VX855_GPI 14
#define NR_VX855_GPO 13
#define NR_VX855_GPIO 15
#define VX855_GPI(n) (n)
#define VX855_GPO(n) (NR_VX855_GPI + (n))
#define VX855_GPIO(n) (NR_VX855_GPI + NR_VX855_GPO + (n))
#include "olpc_dcon.h"
/* Hardware setup on the XO 1.5:
* DCONLOAD connects to VX855_GPIO1 (not SMBCK2)
* DCONBLANK connects to VX855_GPIO8 (not SSPICLK) unused in driver
* DCONSTAT0 connects to VX855_GPI10 (not SSPISDI)
* DCONSTAT1 connects to VX855_GPI11 (not nSSPISS)
* DCONIRQ connects to VX855_GPIO12
* DCONSMBDATA connects to VX855 graphics CRTSPD
* DCONSMBCLK connects to VX855 graphics CRTSPCLK
*/
#define VX855_GENL_PURPOSE_OUTPUT 0x44c /* PMIO_Rx4c-4f */
#define VX855_GPI_STATUS_CHG 0x450 /* PMIO_Rx50 */
#define VX855_GPI_SCI_SMI 0x452 /* PMIO_Rx52 */
#define BIT_GPIO12 0x40
#define PREFIX "OLPC DCON:"
enum dcon_gpios {
OLPC_DCON_STAT0,
OLPC_DCON_STAT1,
OLPC_DCON_LOAD,
};
struct gpiod_lookup_table gpios_table = {
.dev_id = NULL,
.table = {
GPIO_LOOKUP("VX855 South Bridge", VX855_GPIO(1), "dcon_load",
GPIO_ACTIVE_LOW),
GPIO_LOOKUP("VX855 South Bridge", VX855_GPI(10), "dcon_stat0",
GPIO_ACTIVE_LOW),
GPIO_LOOKUP("VX855 South Bridge", VX855_GPI(11), "dcon_stat1",
GPIO_ACTIVE_LOW),
{ },
},
};
static const struct dcon_gpio gpios_asis[] = {
[OLPC_DCON_STAT0] = { .name = "dcon_stat0", .flags = GPIOD_ASIS },
[OLPC_DCON_STAT1] = { .name = "dcon_stat1", .flags = GPIOD_ASIS },
[OLPC_DCON_LOAD] = { .name = "dcon_load", .flags = GPIOD_ASIS },
};
static struct gpio_desc *gpios[3];
static void dcon_clear_irq(void)
{
/* irq status will appear in PMIO_Rx50[6] (RW1C) on gpio12 */
outb(BIT_GPIO12, VX855_GPI_STATUS_CHG);
}
static int dcon_was_irq(void)
{
u8 tmp;
/* irq status will appear in PMIO_Rx50[6] on gpio12 */
tmp = inb(VX855_GPI_STATUS_CHG);
return !!(tmp & BIT_GPIO12);
}
static int dcon_init_xo_1_5(struct dcon_priv *dcon)
{
unsigned int irq;
const struct dcon_gpio *pin = &gpios_asis[0];
int i;
int ret;
/* Add GPIO look up table */
gpios_table.dev_id = dev_name(&dcon->client->dev);
gpiod_add_lookup_table(&gpios_table);
/* Get GPIO descriptor */
for (i = 0; i < ARRAY_SIZE(gpios_asis); i++) {
gpios[i] = devm_gpiod_get(&dcon->client->dev, pin[i].name,
pin[i].flags);
if (IS_ERR(gpios[i])) {
ret = PTR_ERR(gpios[i]);
pr_err("failed to request %s GPIO: %d\n", pin[i].name,
ret);
return ret;
}
}
dcon_clear_irq();
/* set PMIO_Rx52[6] to enable SCI/SMI on gpio12 */
outb(inb(VX855_GPI_SCI_SMI) | BIT_GPIO12, VX855_GPI_SCI_SMI);
/* Determine the current state of DCONLOAD, likely set by firmware */
/* GPIO1 */
dcon->curr_src = (inl(VX855_GENL_PURPOSE_OUTPUT) & 0x1000) ?
DCON_SOURCE_CPU : DCON_SOURCE_DCON;
dcon->pending_src = dcon->curr_src;
/* we're sharing the IRQ with ACPI */
irq = acpi_gbl_FADT.sci_interrupt;
if (request_irq(irq, &dcon_interrupt, IRQF_SHARED, "DCON", dcon)) {
pr_err("DCON (IRQ%d) allocation failed\n", irq);
return 1;
}
return 0;
}
static void set_i2c_line(int sda, int scl)
{
unsigned char tmp;
unsigned int port = 0x26;
/* FIXME: This directly accesses the CRT GPIO controller !!! */
outb(port, 0x3c4);
tmp = inb(0x3c5);
if (scl)
tmp |= 0x20;
else
tmp &= ~0x20;
if (sda)
tmp |= 0x10;
else
tmp &= ~0x10;
tmp |= 0x01;
outb(port, 0x3c4);
outb(tmp, 0x3c5);
}
static void dcon_wiggle_xo_1_5(void)
{
int x;
/*
* According to HiMax, when powering the DCON up we should hold
* SMB_DATA high for 8 SMB_CLK cycles. This will force the DCON
* state machine to reset to a (sane) initial state. Mitch Bradley
* did some testing and discovered that holding for 16 SMB_CLK cycles
* worked a lot more reliably, so that's what we do here.
*/
set_i2c_line(1, 1);
for (x = 0; x < 16; x++) {
udelay(5);
set_i2c_line(1, 0);
udelay(5);
set_i2c_line(1, 1);
}
udelay(5);
/* set PMIO_Rx52[6] to enable SCI/SMI on gpio12 */
outb(inb(VX855_GPI_SCI_SMI) | BIT_GPIO12, VX855_GPI_SCI_SMI);
}
static void dcon_set_dconload_xo_1_5(int val)
{
gpiod_set_value(gpios[OLPC_DCON_LOAD], val);
}
static int dcon_read_status_xo_1_5(u8 *status)
{
if (!dcon_was_irq())
return -1;
/* i believe this is the same as "inb(0x44b) & 3" */
*status = gpiod_get_value(gpios[OLPC_DCON_STAT0]);
*status |= gpiod_get_value(gpios[OLPC_DCON_STAT1]) << 1;
dcon_clear_irq();
return 0;
}
struct dcon_platform_data dcon_pdata_xo_1_5 = {
.init = dcon_init_xo_1_5,
.bus_stabilize_wiggle = dcon_wiggle_xo_1_5,
.set_dconload = dcon_set_dconload_xo_1_5,
.read_status = dcon_read_status_xo_1_5,
};
Codebase Browser
linux