linux/Documentation/devicetree/bindings/iio/adc/adi,ad7091r5.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/iio/adc/adi,ad7091r5.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Analog Devices AD7091R-2/-4/-5/-8 Multi-Channel 12-Bit ADCs

maintainers:
  - Michael Hennerich <[email protected]>
  - Marcelo Schmitt <[email protected]>

description: |
  Analog Devices AD7091R5 4-Channel 12-Bit ADC supporting I2C interface
  https://www.analog.com/media/en/technical-documentation/data-sheets/ad7091r-5.pdf
  Analog Devices AD7091R-2/AD7091R-4/AD7091R-8 2-/4-/8-Channel 12-Bit ADCs
  supporting SPI interface
  https://www.analog.com/media/en/technical-documentation/data-sheets/AD7091R-2_7091R-4_7091R-8.pdf

properties:
  compatible:
    enum:
      - adi,ad7091r2
      - adi,ad7091r4
      - adi,ad7091r5
      - adi,ad7091r8

  reg:
    maxItems: 1

  vdd-supply:
    description:
      Provide VDD power to the sensor (VDD range is from 2.7V to 5.25V).

  vdrive-supply:
    description:
      Determines the voltage level at which the interface logic will operate.
      The V_drive voltage range is from 1.8V to 5.25V and must not exceed VDD by
      more than 0.3V.

  vref-supply:
    description:
      Phandle to the vref power supply

  convst-gpios:
    description:
      GPIO connected to the CONVST pin.
      This logic input is used to initiate conversions on the analog
      input channels.
    maxItems: 1

  reset-gpios:
    maxItems: 1

  interrupts:
    description:
      Interrupt for signaling when conversion results exceed the high limit for
      ADC readings or fall below the low limit for them. Interrupt source must
      be attached to ALERT/BUSY/GPO0 pin.
    maxItems: 1

required:
  - compatible
  - reg

allOf:
  - $ref: /schemas/spi/spi-peripheral-props.yaml#

  # AD7091R-2 does not have ALERT/BUSY/GPO pin
  - if:
      properties:
        compatible:
          contains:
            enum:
              - adi,ad7091r2
    then:
      properties:
        interrupts: false

  - if:
      properties:
        compatible:
          contains:
            enum:
              - adi,ad7091r2
              - adi,ad7091r4
              - adi,ad7091r8
    then:
      required:
        - convst-gpios

unevaluatedProperties: false

examples:
  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>
    i2c {
        #address-cells = <1>;
        #size-cells = <0>;

        adc@2f {
            compatible = "adi,ad7091r5";
            reg = <0x2f>;

            interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
            interrupt-parent = <&gpio>;
        };
    };
  - |
    #include <dt-bindings/gpio/gpio.h>
    #include <dt-bindings/interrupt-controller/irq.h>
    spi {
        #address-cells = <1>;
        #size-cells = <0>;

        adc@0 {
            compatible = "adi,ad7091r8";
            reg = <0x0>;
            spi-max-frequency = <1000000>;
            vref-supply = <&adc_vref>;
            convst-gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
            reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
            interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
            interrupt-parent = <&gpio>;
        };
    };
...