// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family
* of PCI-SCSI IO processors.
*
* Copyright (C) 1999-2001 Gerard Roudier <[email protected]>
* Copyright (c) 2003-2005 Matthew Wilcox <[email protected]>
*
* This driver is derived from the Linux sym53c8xx driver.
* Copyright (C) 1998-2000 Gerard Roudier
*
* The sym53c8xx driver is derived from the ncr53c8xx driver that had been
* a port of the FreeBSD ncr driver to Linux-1.2.13.
*
* The original ncr driver has been written for 386bsd and FreeBSD by
* Wolfgang Stanglmeier <[email protected]>
* Stefan Esser <[email protected]>
* Copyright (C) 1994 Wolfgang Stanglmeier
*
* Other major contributions:
*
* NVRAM detection and reading.
* Copyright (C) 1997 Richard Waltham <[email protected]>
*
*-----------------------------------------------------------------------------
*/
#include <linux/ctype.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/spinlock.h>
#include <scsi/scsi.h>
#include <scsi/scsi_tcq.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_transport.h>
#include "sym_glue.h"
#include "sym_nvram.h"
#define NAME53C "sym53c"
#define NAME53C8XX "sym53c8xx"
struct sym_driver_setup sym_driver_setup = SYM_LINUX_DRIVER_SETUP;
unsigned int sym_debug_flags = 0;
static char *excl_string;
static char *safe_string;
module_param_named(cmd_per_lun, sym_driver_setup.max_tag, ushort, 0);
module_param_named(burst, sym_driver_setup.burst_order, byte, 0);
module_param_named(led, sym_driver_setup.scsi_led, byte, 0);
module_param_named(diff, sym_driver_setup.scsi_diff, byte, 0);
module_param_named(irqm, sym_driver_setup.irq_mode, byte, 0);
module_param_named(buschk, sym_driver_setup.scsi_bus_check, byte, 0);
module_param_named(hostid, sym_driver_setup.host_id, byte, 0);
module_param_named(verb, sym_driver_setup.verbose, byte, 0);
module_param_named(debug, sym_debug_flags, uint, 0);
module_param_named(settle, sym_driver_setup.settle_delay, byte, 0);
module_param_named(nvram, sym_driver_setup.use_nvram, byte, 0);
module_param_named(excl, excl_string, charp, 0);
module_param_named(safe, safe_string, charp, 0);
MODULE_PARM_DESC(cmd_per_lun, "The maximum number of tags to use by default");
MODULE_PARM_DESC(burst, "Maximum burst. 0 to disable, 255 to read from registers");
MODULE_PARM_DESC(led, "Set to 1 to enable LED support");
MODULE_PARM_DESC(diff, "0 for no differential mode, 1 for BIOS, 2 for always, 3 for not GPIO3");
MODULE_PARM_DESC(irqm, "0 for open drain, 1 to leave alone, 2 for totem pole");
MODULE_PARM_DESC(buschk, "0 to not check, 1 for detach on error, 2 for warn on error");
MODULE_PARM_DESC(hostid, "The SCSI ID to use for the host adapters");
MODULE_PARM_DESC(verb, "0 for minimal verbosity, 1 for normal, 2 for excessive");
MODULE_PARM_DESC(debug, "Set bits to enable debugging");
MODULE_PARM_DESC(settle, "Settle delay in seconds. Default 3");
MODULE_PARM_DESC(nvram, "Option currently not used");
MODULE_PARM_DESC(excl, "List ioport addresses here to prevent controllers from being attached");
MODULE_PARM_DESC(safe, "Set other settings to a \"safe mode\"");
MODULE_LICENSE("GPL");
MODULE_VERSION(SYM_VERSION);
MODULE_AUTHOR("Matthew Wilcox <[email protected]>");
MODULE_DESCRIPTION("NCR, Symbios and LSI 8xx and 1010 PCI SCSI adapters");
static void sym2_setup_params(void)
{
char *p = excl_string;
int xi = 0;
while (p && (xi < 8)) {
char *next_p;
int val = (int) simple_strtoul(p, &next_p, 0);
sym_driver_setup.excludes[xi++] = val;
p = next_p;
}
if (safe_string) {
if (*safe_string == 'y') {
sym_driver_setup.max_tag = 0;
sym_driver_setup.burst_order = 0;
sym_driver_setup.scsi_led = 0;
sym_driver_setup.scsi_diff = 1;
sym_driver_setup.irq_mode = 0;
sym_driver_setup.scsi_bus_check = 2;
sym_driver_setup.host_id = 7;
sym_driver_setup.verbose = 2;
sym_driver_setup.settle_delay = 10;
sym_driver_setup.use_nvram = 1;
} else if (*safe_string != 'n') {
printk(KERN_WARNING NAME53C8XX "Ignoring parameter %s"
" passed to safe option", safe_string);
}
}
}
static struct scsi_transport_template *sym2_transport_template = NULL;
/*
* Driver private area in the SCSI command structure.
*/
struct sym_ucmd { /* Override the SCSI pointer structure */
struct completion *eh_done; /* SCSI error handling */
};
#define SYM_UCMD_PTR(cmd) ((struct sym_ucmd *)scsi_cmd_priv(cmd))
#define SYM_SOFTC_PTR(cmd) sym_get_hcb(cmd->device->host)
/*
* Complete a pending CAM CCB.
*/
void sym_xpt_done(struct sym_hcb *np, struct scsi_cmnd *cmd)
{
struct sym_ucmd *ucmd = SYM_UCMD_PTR(cmd);
if (ucmd->eh_done)
complete(ucmd->eh_done);
scsi_dma_unmap(cmd);
scsi_done(cmd);
}
/*
* Tell the SCSI layer about a BUS RESET.
*/
void sym_xpt_async_bus_reset(struct sym_hcb *np)
{
printf_notice("%s: SCSI BUS has been reset.\n", sym_name(np));
np->s.settle_time = jiffies + sym_driver_setup.settle_delay * HZ;
np->s.settle_time_valid = 1;
if (sym_verbose >= 2)
printf_info("%s: command processing suspended for %d seconds\n",
sym_name(np), sym_driver_setup.settle_delay);
}
/*
* Choose the more appropriate CAM status if
* the IO encountered an extended error.
*/
static int sym_xerr_cam_status(int cam_status, int x_status)
{
if (x_status) {
if (x_status & XE_PARITY_ERR)
cam_status = DID_PARITY;
else
cam_status = DID_ERROR;
}
return cam_status;
}
/*
* Build CAM result for a failed or auto-sensed IO.
*/
void sym_set_cam_result_error(struct sym_hcb *np, struct sym_ccb *cp, int resid)
{
struct scsi_cmnd *cmd = cp->cmd;
u_int cam_status, scsi_status;
cam_status = DID_OK;
scsi_status = cp->ssss_status;
if (cp->host_flags & HF_SENSE) {
scsi_status = cp->sv_scsi_status;
resid = cp->sv_resid;
if (sym_verbose && cp->sv_xerr_status)
sym_print_xerr(cmd, cp->sv_xerr_status);
if (cp->host_status == HS_COMPLETE &&
cp->ssss_status == S_GOOD &&
cp->xerr_status == 0) {
cam_status = sym_xerr_cam_status(DID_OK,
cp->sv_xerr_status);
/*
* Bounce back the sense data to user.
*/
memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE);
memcpy(cmd->sense_buffer, cp->sns_bbuf,
min(SCSI_SENSE_BUFFERSIZE, SYM_SNS_BBUF_LEN));
#if 0
/*
* If the device reports a UNIT ATTENTION condition
* due to a RESET condition, we should consider all
* disconnect CCBs for this unit as aborted.
*/
if (1) {
u_char *p;
p = (u_char *) cmd->sense_data;
if (p[0]==0x70 && p[2]==0x6 && p[12]==0x29)
sym_clear_tasks(np, DID_ABORT,
cp->target,cp->lun, -1);
}
#endif
} else {
/*
* Error return from our internal request sense. This
* is bad: we must clear the contingent allegiance
* condition otherwise the device will always return
* BUSY. Use a big stick.
*/
sym_reset_scsi_target(np, cmd->device->id);
cam_status = DID_ERROR;
}
} else if (cp->host_status == HS_COMPLETE) /* Bad SCSI status */
cam_status = DID_OK;
else if (cp->host_status == HS_SEL_TIMEOUT) /* Selection timeout */
cam_status = DID_NO_CONNECT;
else if (cp->host_status == HS_UNEXPECTED) /* Unexpected BUS FREE*/
cam_status = DID_ERROR;
else { /* Extended error */
if (sym_verbose) {
sym_print_addr(cmd, "COMMAND FAILED (%x %x %x).\n",
cp->host_status, cp->ssss_status,
cp->xerr_status);
}
/*
* Set the most appropriate value for CAM status.
*/
cam_status = sym_xerr_cam_status(DID_ERROR, cp->xerr_status);
}
scsi_set_resid(cmd, resid);
cmd->result = (cam_status << 16) | scsi_status;
}
static int sym_scatter(struct sym_hcb *np, struct sym_ccb *cp, struct scsi_cmnd *cmd)
{
int segment;
int use_sg;
cp->data_len = 0;
use_sg = scsi_dma_map(cmd);
if (use_sg > 0) {
struct scatterlist *sg;
struct sym_tcb *tp = &np->target[cp->target];
struct sym_tblmove *data;
if (use_sg > SYM_CONF_MAX_SG) {
scsi_dma_unmap(cmd);
return -1;
}
data = &cp->phys.data[SYM_CONF_MAX_SG - use_sg];
scsi_for_each_sg(cmd, sg, use_sg, segment) {
dma_addr_t baddr = sg_dma_address(sg);
unsigned int len = sg_dma_len(sg);
if ((len & 1) && (tp->head.wval & EWS)) {
len++;
cp->odd_byte_adjustment++;
}
sym_build_sge(np, &data[segment], baddr, len);
cp->data_len += len;
}
} else {
segment = -2;
}
return segment;
}
/*
* Queue a SCSI command.
*/
static int sym_queue_command(struct sym_hcb *np, struct scsi_cmnd *cmd)
{
struct scsi_device *sdev = cmd->device;
struct sym_tcb *tp;
struct sym_lcb *lp;
struct sym_ccb *cp;
int order;
/*
* Retrieve the target descriptor.
*/
tp = &np->target[sdev->id];
/*
* Select tagged/untagged.
*/
lp = sym_lp(tp, sdev->lun);
order = (lp && lp->s.reqtags) ? M_SIMPLE_TAG : 0;
/*
* Queue the SCSI IO.
*/
cp = sym_get_ccb(np, cmd, order);
if (!cp)
return 1; /* Means resource shortage */
sym_queue_scsiio(np, cmd, cp);
return 0;
}
/*
* Setup buffers and pointers that address the CDB.
*/
static inline int sym_setup_cdb(struct sym_hcb *np, struct scsi_cmnd *cmd, struct sym_ccb *cp)
{
memcpy(cp->cdb_buf, cmd->cmnd, cmd->cmd_len);
cp->phys.cmd.addr = CCB_BA(cp, cdb_buf[0]);
cp->phys.cmd.size = cpu_to_scr(cmd->cmd_len);
return 0;
}
/*
* Setup pointers that address the data and start the I/O.
*/
int sym_setup_data_and_start(struct sym_hcb *np, struct scsi_cmnd *cmd, struct sym_ccb *cp)
{
u32 lastp, goalp;
int dir;
/*
* Build the CDB.
*/
if (sym_setup_cdb(np, cmd, cp))
goto out_abort;
/*
* No direction means no data.
*/
dir = cmd->sc_data_direction;
if (dir != DMA_NONE) {
cp->segments = sym_scatter(np, cp, cmd);
if (cp->segments < 0) {
sym_set_cam_status(cmd, DID_ERROR);
goto out_abort;
}
/*
* No segments means no data.
*/
if (!cp->segments)
dir = DMA_NONE;
} else {
cp->data_len = 0;
cp->segments = 0;
}
/*
* Set the data pointer.
*/
switch (dir) {
case DMA_BIDIRECTIONAL:
scmd_printk(KERN_INFO, cmd, "got DMA_BIDIRECTIONAL command");
sym_set_cam_status(cmd, DID_ERROR);
goto out_abort;
case DMA_TO_DEVICE:
goalp = SCRIPTA_BA(np, data_out2) + 8;
lastp = goalp - 8 - (cp->segments * (2*4));
break;
case DMA_FROM_DEVICE:
cp->host_flags |= HF_DATA_IN;
goalp = SCRIPTA_BA(np, data_in2) + 8;
lastp = goalp - 8 - (cp->segments * (2*4));
break;
case DMA_NONE:
default:
lastp = goalp = SCRIPTB_BA(np, no_data);
break;
}
/*
* Set all pointers values needed by SCRIPTS.
*/
cp->phys.head.lastp = cpu_to_scr(lastp);
cp->phys.head.savep = cpu_to_scr(lastp);
cp->startp = cp->phys.head.savep;
cp->goalp = cpu_to_scr(goalp);
/*
* When `#ifed 1', the code below makes the driver
* panic on the first attempt to write to a SCSI device.
* It is the first test we want to do after a driver
* change that does not seem obviously safe. :)
*/
#if 0
switch (cp->cdb_buf[0]) {
case 0x0A: case 0x2A: case 0xAA:
panic("XXXXXXXXXXXXX WRITE NOT YET ALLOWED XXXXXXXXXXXXXX\n");
break;
default:
break;
}
#endif
/*
* activate this job.
*/
sym_put_start_queue(np, cp);
return 0;
out_abort:
sym_free_ccb(np, cp);
sym_xpt_done(np, cmd);
return 0;
}
/*
* timer daemon.
*
* Misused to keep the driver running when
* interrupts are not configured correctly.
*/
static void sym_timer(struct sym_hcb *np)
{
unsigned long thistime = jiffies;
/*
* Restart the timer.
*/
np->s.timer.expires = thistime + SYM_CONF_TIMER_INTERVAL;
add_timer(&np->s.timer);
/*
* If we are resetting the ncr, wait for settle_time before
* clearing it. Then command processing will be resumed.
*/
if (np->s.settle_time_valid) {
if (time_before_eq(np->s.settle_time, thistime)) {
if (sym_verbose >= 2 )
printk("%s: command processing resumed\n",
sym_name(np));
np->s.settle_time_valid = 0;
}
return;
}
/*
* Nothing to do for now, but that may come.
*/
if (np->s.lasttime + 4*HZ < thistime) {
np->s.lasttime = thistime;
}
#ifdef SYM_CONF_PCIQ_MAY_MISS_COMPLETIONS
/*
* Some way-broken PCI bridges may lead to
* completions being lost when the clearing
* of the INTFLY flag by the CPU occurs
* concurrently with the chip raising this flag.
* If this ever happen, lost completions will
* be reaped here.
*/
sym_wakeup_done(np);
#endif
}
/*
* PCI BUS error handler.
*/
void sym_log_bus_error(struct Scsi_Host *shost)
{
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
unsigned short pci_sts;
pci_read_config_word(pdev, PCI_STATUS, &pci_sts);
if (pci_sts & 0xf900) {
pci_write_config_word(pdev, PCI_STATUS, pci_sts);
shost_printk(KERN_WARNING, shost,
"PCI bus error: status = 0x%04x\n", pci_sts & 0xf900);
}
}
/*
* queuecommand method. Entered with the host adapter lock held and
* interrupts disabled.
*/
static int sym53c8xx_queue_command_lck(struct scsi_cmnd *cmd)
{
struct sym_hcb *np = SYM_SOFTC_PTR(cmd);
struct sym_ucmd *ucp = SYM_UCMD_PTR(cmd);
int sts = 0;
memset(ucp, 0, sizeof(*ucp));
/*
* Shorten our settle_time if needed for
* this command not to time out.
*/
if (np->s.settle_time_valid && scsi_cmd_to_rq(cmd)->timeout) {
unsigned long tlimit = jiffies + scsi_cmd_to_rq(cmd)->timeout;
tlimit -= SYM_CONF_TIMER_INTERVAL*2;
if (time_after(np->s.settle_time, tlimit)) {
np->s.settle_time = tlimit;
}
}
if (np->s.settle_time_valid)
return SCSI_MLQUEUE_HOST_BUSY;
sts = sym_queue_command(np, cmd);
if (sts)
return SCSI_MLQUEUE_HOST_BUSY;
return 0;
}
static DEF_SCSI_QCMD(sym53c8xx_queue_command)
/*
* Linux entry point of the interrupt handler.
*/
static irqreturn_t sym53c8xx_intr(int irq, void *dev_id)
{
struct Scsi_Host *shost = dev_id;
struct sym_data *sym_data = shost_priv(shost);
irqreturn_t result;
/* Avoid spinloop trying to handle interrupts on frozen device */
if (pci_channel_offline(sym_data->pdev))
return IRQ_NONE;
if (DEBUG_FLAGS & DEBUG_TINY) printf_debug ("[");
spin_lock(shost->host_lock);
result = sym_interrupt(shost);
spin_unlock(shost->host_lock);
if (DEBUG_FLAGS & DEBUG_TINY) printf_debug ("]\n");
return result;
}
/*
* Linux entry point of the timer handler
*/
static void sym53c8xx_timer(struct timer_list *t)
{
struct sym_hcb *np = from_timer(np, t, s.timer);
unsigned long flags;
spin_lock_irqsave(np->s.host->host_lock, flags);
sym_timer(np);
spin_unlock_irqrestore(np->s.host->host_lock, flags);
}
/*
* What the eh thread wants us to perform.
*/
#define SYM_EH_ABORT 0
#define SYM_EH_DEVICE_RESET 1
/*
* Generic method for our eh processing.
* The 'op' argument tells what we have to do.
*/
/*
* Error handlers called from the eh thread (one thread per HBA).
*/
static int sym53c8xx_eh_abort_handler(struct scsi_cmnd *cmd)
{
struct sym_ucmd *ucmd = SYM_UCMD_PTR(cmd);
struct Scsi_Host *shost = cmd->device->host;
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
SYM_QUEHEAD *qp;
int cmd_queued = 0;
int sts = -1;
struct completion eh_done;
scmd_printk(KERN_WARNING, cmd, "ABORT operation started\n");
/*
* Escalate to host reset if the PCI bus went down
*/
if (pci_channel_offline(pdev))
return SCSI_FAILED;
spin_lock_irq(shost->host_lock);
/* This one is queued in some place -> to wait for completion */
FOR_EACH_QUEUED_ELEMENT(&np->busy_ccbq, qp) {
struct sym_ccb *cp = sym_que_entry(qp, struct sym_ccb, link_ccbq);
if (cp->cmd == cmd) {
cmd_queued = 1;
break;
}
}
sts = sym_abort_scsiio(np, cmd, 1);
/* On error, restore everything and cross fingers :) */
if (sts)
cmd_queued = 0;
if (cmd_queued) {
init_completion(&eh_done);
ucmd->eh_done = &eh_done;
spin_unlock_irq(shost->host_lock);
if (!wait_for_completion_timeout(&eh_done, 5*HZ)) {
ucmd->eh_done = NULL;
sts = -2;
}
} else {
spin_unlock_irq(shost->host_lock);
}
dev_warn(&cmd->device->sdev_gendev, "ABORT operation %s.\n",
sts==0 ? "complete" :sts==-2 ? "timed-out" : "failed");
return sts ? SCSI_FAILED : SCSI_SUCCESS;
}
static int sym53c8xx_eh_target_reset_handler(struct scsi_cmnd *cmd)
{
struct scsi_target *starget = scsi_target(cmd->device);
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
SYM_QUEHEAD *qp;
int sts;
struct completion eh_done;
starget_printk(KERN_WARNING, starget,
"TARGET RESET operation started\n");
/*
* Escalate to host reset if the PCI bus went down
*/
if (pci_channel_offline(pdev))
return SCSI_FAILED;
spin_lock_irq(shost->host_lock);
sts = sym_reset_scsi_target(np, starget->id);
if (!sts) {
FOR_EACH_QUEUED_ELEMENT(&np->busy_ccbq, qp) {
struct sym_ccb *cp = sym_que_entry(qp, struct sym_ccb,
link_ccbq);
struct scsi_cmnd *cmd = cp->cmd;
struct sym_ucmd *ucmd;
if (!cmd || cmd->device->channel != starget->channel ||
cmd->device->id != starget->id)
continue;
ucmd = SYM_UCMD_PTR(cmd);
init_completion(&eh_done);
ucmd->eh_done = &eh_done;
spin_unlock_irq(shost->host_lock);
if (!wait_for_completion_timeout(&eh_done, 5*HZ)) {
ucmd->eh_done = NULL;
sts = -2;
}
spin_lock_irq(shost->host_lock);
}
}
spin_unlock_irq(shost->host_lock);
starget_printk(KERN_WARNING, starget, "TARGET RESET operation %s.\n",
sts==0 ? "complete" :sts==-2 ? "timed-out" : "failed");
return SCSI_SUCCESS;
}
static int sym53c8xx_eh_bus_reset_handler(struct scsi_cmnd *cmd)
{
struct Scsi_Host *shost = cmd->device->host;
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
scmd_printk(KERN_WARNING, cmd, "BUS RESET operation started\n");
/*
* Escalate to host reset if the PCI bus went down
*/
if (pci_channel_offline(pdev))
return SCSI_FAILED;
spin_lock_irq(shost->host_lock);
sym_reset_scsi_bus(np, 1);
spin_unlock_irq(shost->host_lock);
dev_warn(&cmd->device->sdev_gendev, "BUS RESET operation complete.\n");
return SCSI_SUCCESS;
}
static int sym53c8xx_eh_host_reset_handler(struct scsi_cmnd *cmd)
{
struct Scsi_Host *shost = cmd->device->host;
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
struct completion eh_done;
int finished_reset = 1;
shost_printk(KERN_WARNING, shost, "HOST RESET operation started\n");
/* We may be in an error condition because the PCI bus
* went down. In this case, we need to wait until the
* PCI bus is reset, the card is reset, and only then
* proceed with the scsi error recovery. There's no
* point in hurrying; take a leisurely wait.
*/
#define WAIT_FOR_PCI_RECOVERY 35
if (pci_channel_offline(pdev)) {
init_completion(&eh_done);
spin_lock_irq(shost->host_lock);
/* Make sure we didn't race */
if (pci_channel_offline(pdev)) {
BUG_ON(sym_data->io_reset);
sym_data->io_reset = &eh_done;
finished_reset = 0;
}
spin_unlock_irq(shost->host_lock);
if (!finished_reset)
finished_reset = wait_for_completion_timeout
(sym_data->io_reset,
WAIT_FOR_PCI_RECOVERY*HZ);
spin_lock_irq(shost->host_lock);
sym_data->io_reset = NULL;
spin_unlock_irq(shost->host_lock);
}
if (finished_reset) {
sym_reset_scsi_bus(np, 0);
sym_start_up(shost, 1);
}
shost_printk(KERN_WARNING, shost, "HOST RESET operation %s.\n",
finished_reset==1 ? "complete" : "failed");
return finished_reset ? SCSI_SUCCESS : SCSI_FAILED;
}
/*
* Tune device queuing depth, according to various limits.
*/
static void sym_tune_dev_queuing(struct sym_tcb *tp, int lun, u_short reqtags)
{
struct sym_lcb *lp = sym_lp(tp, lun);
u_short oldtags;
if (!lp)
return;
oldtags = lp->s.reqtags;
if (reqtags > lp->s.scdev_depth)
reqtags = lp->s.scdev_depth;
lp->s.reqtags = reqtags;
if (reqtags != oldtags) {
dev_info(&tp->starget->dev,
"tagged command queuing %s, command queue depth %d.\n",
lp->s.reqtags ? "enabled" : "disabled", reqtags);
}
}
static int sym53c8xx_slave_alloc(struct scsi_device *sdev)
{
struct sym_hcb *np = sym_get_hcb(sdev->host);
struct sym_tcb *tp = &np->target[sdev->id];
struct sym_lcb *lp;
unsigned long flags;
int error;
if (sdev->id >= SYM_CONF_MAX_TARGET || sdev->lun >= SYM_CONF_MAX_LUN)
return -ENXIO;
spin_lock_irqsave(np->s.host->host_lock, flags);
/*
* Fail the device init if the device is flagged NOSCAN at BOOT in
* the NVRAM. This may speed up boot and maintain coherency with
* BIOS device numbering. Clearing the flag allows the user to
* rescan skipped devices later. We also return an error for
* devices not flagged for SCAN LUNS in the NVRAM since some single
* lun devices behave badly when asked for a non zero LUN.
*/
if (tp->usrflags & SYM_SCAN_BOOT_DISABLED) {
tp->usrflags &= ~SYM_SCAN_BOOT_DISABLED;
starget_printk(KERN_INFO, sdev->sdev_target,
"Scan at boot disabled in NVRAM\n");
error = -ENXIO;
goto out;
}
if (tp->usrflags & SYM_SCAN_LUNS_DISABLED) {
if (sdev->lun != 0) {
error = -ENXIO;
goto out;
}
starget_printk(KERN_INFO, sdev->sdev_target,
"Multiple LUNs disabled in NVRAM\n");
}
lp = sym_alloc_lcb(np, sdev->id, sdev->lun);
if (!lp) {
error = -ENOMEM;
goto out;
}
if (tp->nlcb == 1)
tp->starget = sdev->sdev_target;
spi_min_period(tp->starget) = tp->usr_period;
spi_max_width(tp->starget) = tp->usr_width;
error = 0;
out:
spin_unlock_irqrestore(np->s.host->host_lock, flags);
return error;
}
/*
* Linux entry point for device queue sizing.
*/
static int sym53c8xx_slave_configure(struct scsi_device *sdev)
{
struct sym_hcb *np = sym_get_hcb(sdev->host);
struct sym_tcb *tp = &np->target[sdev->id];
struct sym_lcb *lp = sym_lp(tp, sdev->lun);
int reqtags, depth_to_use;
/*
* Get user flags.
*/
lp->curr_flags = lp->user_flags;
/*
* Select queue depth from driver setup.
* Do not use more than configured by user.
* Use at least 1.
* Do not use more than our maximum.
*/
reqtags = sym_driver_setup.max_tag;
if (reqtags > tp->usrtags)
reqtags = tp->usrtags;
if (!sdev->tagged_supported)
reqtags = 0;
if (reqtags > SYM_CONF_MAX_TAG)
reqtags = SYM_CONF_MAX_TAG;
depth_to_use = reqtags ? reqtags : 1;
scsi_change_queue_depth(sdev, depth_to_use);
lp->s.scdev_depth = depth_to_use;
sym_tune_dev_queuing(tp, sdev->lun, reqtags);
if (!spi_initial_dv(sdev->sdev_target))
spi_dv_device(sdev);
return 0;
}
static void sym53c8xx_slave_destroy(struct scsi_device *sdev)
{
struct sym_hcb *np = sym_get_hcb(sdev->host);
struct sym_tcb *tp = &np->target[sdev->id];
struct sym_lcb *lp = sym_lp(tp, sdev->lun);
unsigned long flags;
/* if slave_alloc returned before allocating a sym_lcb, return */
if (!lp)
return;
spin_lock_irqsave(np->s.host->host_lock, flags);
if (lp->busy_itlq || lp->busy_itl) {
/*
* This really shouldn't happen, but we can't return an error
* so let's try to stop all on-going I/O.
*/
starget_printk(KERN_WARNING, tp->starget,
"Removing busy LCB (%d)\n", (u8)sdev->lun);
sym_reset_scsi_bus(np, 1);
}
if (sym_free_lcb(np, sdev->id, sdev->lun) == 0) {
/*
* It was the last unit for this target.
*/
tp->head.sval = 0;
tp->head.wval = np->rv_scntl3;
tp->head.uval = 0;
tp->tgoal.check_nego = 1;
tp->starget = NULL;
}
spin_unlock_irqrestore(np->s.host->host_lock, flags);
}
/*
* Linux entry point for info() function
*/
static const char *sym53c8xx_info (struct Scsi_Host *host)
{
return SYM_DRIVER_NAME;
}
#ifdef SYM_LINUX_PROC_INFO_SUPPORT
/*
* Proc file system stuff
*
* A read operation returns adapter information.
* A write operation is a control command.
* The string is parsed in the driver code and the command is passed
* to the sym_usercmd() function.
*/
#ifdef SYM_LINUX_USER_COMMAND_SUPPORT
struct sym_usrcmd {
u_long target;
u_long lun;
u_long data;
u_long cmd;
};
#define UC_SETSYNC 10
#define UC_SETTAGS 11
#define UC_SETDEBUG 12
#define UC_SETWIDE 14
#define UC_SETFLAG 15
#define UC_SETVERBOSE 17
#define UC_RESETDEV 18
#define UC_CLEARDEV 19
static void sym_exec_user_command (struct sym_hcb *np, struct sym_usrcmd *uc)
{
struct sym_tcb *tp;
int t, l;
switch (uc->cmd) {
case 0: return;
#ifdef SYM_LINUX_DEBUG_CONTROL_SUPPORT
case UC_SETDEBUG:
sym_debug_flags = uc->data;
break;
#endif
case UC_SETVERBOSE:
np->verbose = uc->data;
break;
default:
/*
* We assume that other commands apply to targets.
* This should always be the case and avoid the below
* 4 lines to be repeated 6 times.
*/
for (t = 0; t < SYM_CONF_MAX_TARGET; t++) {
if (!((uc->target >> t) & 1))
continue;
tp = &np->target[t];
if (!tp->nlcb)
continue;
switch (uc->cmd) {
case UC_SETSYNC:
if (!uc->data || uc->data >= 255) {
tp->tgoal.iu = tp->tgoal.dt =
tp->tgoal.qas = 0;
tp->tgoal.offset = 0;
} else if (uc->data <= 9 && np->minsync_dt) {
if (uc->data < np->minsync_dt)
uc->data = np->minsync_dt;
tp->tgoal.iu = tp->tgoal.dt =
tp->tgoal.qas = 1;
tp->tgoal.width = 1;
tp->tgoal.period = uc->data;
tp->tgoal.offset = np->maxoffs_dt;
} else {
if (uc->data < np->minsync)
uc->data = np->minsync;
tp->tgoal.iu = tp->tgoal.dt =
tp->tgoal.qas = 0;
tp->tgoal.period = uc->data;
tp->tgoal.offset = np->maxoffs;
}
tp->tgoal.check_nego = 1;
break;
case UC_SETWIDE:
tp->tgoal.width = uc->data ? 1 : 0;
tp->tgoal.check_nego = 1;
break;
case UC_SETTAGS:
for (l = 0; l < SYM_CONF_MAX_LUN; l++)
sym_tune_dev_queuing(tp, l, uc->data);
break;
case UC_RESETDEV:
tp->to_reset = 1;
np->istat_sem = SEM;
OUTB(np, nc_istat, SIGP|SEM);
break;
case UC_CLEARDEV:
for (l = 0; l < SYM_CONF_MAX_LUN; l++) {
struct sym_lcb *lp = sym_lp(tp, l);
if (lp) lp->to_clear = 1;
}
np->istat_sem = SEM;
OUTB(np, nc_istat, SIGP|SEM);
break;
case UC_SETFLAG:
tp->usrflags = uc->data;
break;
}
}
break;
}
}
static int sym_skip_spaces(char *ptr, int len)
{
int cnt, c;
for (cnt = len; cnt > 0 && (c = *ptr++) && isspace(c); cnt--);
return (len - cnt);
}
static int get_int_arg(char *ptr, int len, u_long *pv)
{
char *end;
*pv = simple_strtoul(ptr, &end, 10);
return (end - ptr);
}
static int is_keyword(char *ptr, int len, char *verb)
{
int verb_len = strlen(verb);
if (len >= verb_len && !memcmp(verb, ptr, verb_len))
return verb_len;
else
return 0;
}
#define SKIP_SPACES(ptr, len) \
if ((arg_len = sym_skip_spaces(ptr, len)) < 1) \
return -EINVAL; \
ptr += arg_len; len -= arg_len;
#define GET_INT_ARG(ptr, len, v) \
if (!(arg_len = get_int_arg(ptr, len, &(v)))) \
return -EINVAL; \
ptr += arg_len; len -= arg_len;
/*
* Parse a control command
*/
static int sym_user_command(struct Scsi_Host *shost, char *buffer, int length)
{
struct sym_hcb *np = sym_get_hcb(shost);
char *ptr = buffer;
int len = length;
struct sym_usrcmd cmd, *uc = &cmd;
int arg_len;
u_long target;
memset(uc, 0, sizeof(*uc));
if (len > 0 && ptr[len-1] == '\n')
--len;
if ((arg_len = is_keyword(ptr, len, "setsync")) != 0)
uc->cmd = UC_SETSYNC;
else if ((arg_len = is_keyword(ptr, len, "settags")) != 0)
uc->cmd = UC_SETTAGS;
else if ((arg_len = is_keyword(ptr, len, "setverbose")) != 0)
uc->cmd = UC_SETVERBOSE;
else if ((arg_len = is_keyword(ptr, len, "setwide")) != 0)
uc->cmd = UC_SETWIDE;
#ifdef SYM_LINUX_DEBUG_CONTROL_SUPPORT
else if ((arg_len = is_keyword(ptr, len, "setdebug")) != 0)
uc->cmd = UC_SETDEBUG;
#endif
else if ((arg_len = is_keyword(ptr, len, "setflag")) != 0)
uc->cmd = UC_SETFLAG;
else if ((arg_len = is_keyword(ptr, len, "resetdev")) != 0)
uc->cmd = UC_RESETDEV;
else if ((arg_len = is_keyword(ptr, len, "cleardev")) != 0)
uc->cmd = UC_CLEARDEV;
else
arg_len = 0;
#ifdef DEBUG_PROC_INFO
printk("sym_user_command: arg_len=%d, cmd=%ld\n", arg_len, uc->cmd);
#endif
if (!arg_len)
return -EINVAL;
ptr += arg_len; len -= arg_len;
switch(uc->cmd) {
case UC_SETSYNC:
case UC_SETTAGS:
case UC_SETWIDE:
case UC_SETFLAG:
case UC_RESETDEV:
case UC_CLEARDEV:
SKIP_SPACES(ptr, len);
if ((arg_len = is_keyword(ptr, len, "all")) != 0) {
ptr += arg_len; len -= arg_len;
uc->target = ~0;
} else {
GET_INT_ARG(ptr, len, target);
uc->target = (1<<target);
#ifdef DEBUG_PROC_INFO
printk("sym_user_command: target=%ld\n", target);
#endif
}
break;
}
switch(uc->cmd) {
case UC_SETVERBOSE:
case UC_SETSYNC:
case UC_SETTAGS:
case UC_SETWIDE:
SKIP_SPACES(ptr, len);
GET_INT_ARG(ptr, len, uc->data);
#ifdef DEBUG_PROC_INFO
printk("sym_user_command: data=%ld\n", uc->data);
#endif
break;
#ifdef SYM_LINUX_DEBUG_CONTROL_SUPPORT
case UC_SETDEBUG:
while (len > 0) {
SKIP_SPACES(ptr, len);
if ((arg_len = is_keyword(ptr, len, "alloc")))
uc->data |= DEBUG_ALLOC;
else if ((arg_len = is_keyword(ptr, len, "phase")))
uc->data |= DEBUG_PHASE;
else if ((arg_len = is_keyword(ptr, len, "queue")))
uc->data |= DEBUG_QUEUE;
else if ((arg_len = is_keyword(ptr, len, "result")))
uc->data |= DEBUG_RESULT;
else if ((arg_len = is_keyword(ptr, len, "scatter")))
uc->data |= DEBUG_SCATTER;
else if ((arg_len = is_keyword(ptr, len, "script")))
uc->data |= DEBUG_SCRIPT;
else if ((arg_len = is_keyword(ptr, len, "tiny")))
uc->data |= DEBUG_TINY;
else if ((arg_len = is_keyword(ptr, len, "timing")))
uc->data |= DEBUG_TIMING;
else if ((arg_len = is_keyword(ptr, len, "nego")))
uc->data |= DEBUG_NEGO;
else if ((arg_len = is_keyword(ptr, len, "tags")))
uc->data |= DEBUG_TAGS;
else if ((arg_len = is_keyword(ptr, len, "pointer")))
uc->data |= DEBUG_POINTER;
else
return -EINVAL;
ptr += arg_len; len -= arg_len;
}
#ifdef DEBUG_PROC_INFO
printk("sym_user_command: data=%ld\n", uc->data);
#endif
break;
#endif /* SYM_LINUX_DEBUG_CONTROL_SUPPORT */
case UC_SETFLAG:
while (len > 0) {
SKIP_SPACES(ptr, len);
if ((arg_len = is_keyword(ptr, len, "no_disc")))
uc->data &= ~SYM_DISC_ENABLED;
else
return -EINVAL;
ptr += arg_len; len -= arg_len;
}
break;
default:
break;
}
if (len)
return -EINVAL;
else {
unsigned long flags;
spin_lock_irqsave(shost->host_lock, flags);
sym_exec_user_command(np, uc);
spin_unlock_irqrestore(shost->host_lock, flags);
}
return length;
}
#endif /* SYM_LINUX_USER_COMMAND_SUPPORT */
/*
* Copy formatted information into the input buffer.
*/
static int sym_show_info(struct seq_file *m, struct Scsi_Host *shost)
{
#ifdef SYM_LINUX_USER_INFO_SUPPORT
struct sym_data *sym_data = shost_priv(shost);
struct pci_dev *pdev = sym_data->pdev;
struct sym_hcb *np = sym_data->ncb;
seq_printf(m, "Chip " NAME53C "%s, device id 0x%x, "
"revision id 0x%x\n", np->s.chip_name,
pdev->device, pdev->revision);
seq_printf(m, "At PCI address %s, IRQ %u\n",
pci_name(pdev), pdev->irq);
seq_printf(m, "Min. period factor %d, %s SCSI BUS%s\n",
(int) (np->minsync_dt ? np->minsync_dt : np->minsync),
np->maxwide ? "Wide" : "Narrow",
np->minsync_dt ? ", DT capable" : "");
seq_printf(m, "Max. started commands %d, "
"max. commands per LUN %d\n",
SYM_CONF_MAX_START, SYM_CONF_MAX_TAG);
return 0;
#else
return -EINVAL;
#endif /* SYM_LINUX_USER_INFO_SUPPORT */
}
#endif /* SYM_LINUX_PROC_INFO_SUPPORT */
/*
* Free resources claimed by sym_iomap_device(). Note that
* sym_free_resources() should be used instead of this function after calling
* sym_attach().
*/
static void sym_iounmap_device(struct sym_device *device)
{
if (device->s.ioaddr)
pci_iounmap(device->pdev, device->s.ioaddr);
if (device->s.ramaddr)
pci_iounmap(device->pdev, device->s.ramaddr);
}
/*
* Free controller resources.
*/
static void sym_free_resources(struct sym_hcb *np, struct pci_dev *pdev,
int do_free_irq)
{
/*
* Free O/S specific resources.
*/
if (do_free_irq)
free_irq(pdev->irq, np->s.host);
if (np->s.ioaddr)
pci_iounmap(pdev, np->s.ioaddr);
if (np->s.ramaddr)
pci_iounmap(pdev, np->s.ramaddr);
/*
* Free O/S independent resources.
*/
sym_hcb_free(np);
sym_mfree_dma(np, sizeof(*np), "HCB");
}
/*
* Host attach and initialisations.
*
* Allocate host data and ncb structure.
* Remap MMIO region.
* Do chip initialization.
* If all is OK, install interrupt handling and
* start the timer daemon.
*/
static struct Scsi_Host *sym_attach(const struct scsi_host_template *tpnt, int unit,
struct sym_device *dev)
{
struct sym_data *sym_data;
struct sym_hcb *np = NULL;
struct Scsi_Host *shost = NULL;
struct pci_dev *pdev = dev->pdev;
unsigned long flags;
struct sym_fw *fw;
int do_free_irq = 0;
printk(KERN_INFO "sym%d: <%s> rev 0x%x at pci %s irq %u\n",
unit, dev->chip.name, pdev->revision, pci_name(pdev),
pdev->irq);
/*
* Get the firmware for this chip.
*/
fw = sym_find_firmware(&dev->chip);
if (!fw)
goto attach_failed;
shost = scsi_host_alloc(tpnt, sizeof(*sym_data));
if (!shost)
goto attach_failed;
sym_data = shost_priv(shost);
/*
* Allocate immediately the host control block,
* since we are only expecting to succeed. :)
* We keep track in the HCB of all the resources that
* are to be released on error.
*/
np = __sym_calloc_dma(&pdev->dev, sizeof(*np), "HCB");
if (!np)
goto attach_failed;
np->bus_dmat = &pdev->dev; /* Result in 1 DMA pool per HBA */
sym_data->ncb = np;
sym_data->pdev = pdev;
np->s.host = shost;
pci_set_drvdata(pdev, shost);
/*
* Copy some useful infos to the HCB.
*/
np->hcb_ba = vtobus(np);
np->verbose = sym_driver_setup.verbose;
np->s.unit = unit;
np->features = dev->chip.features;
np->clock_divn = dev->chip.nr_divisor;
np->maxoffs = dev->chip.offset_max;
np->maxburst = dev->chip.burst_max;
np->myaddr = dev->host_id;
np->mmio_ba = (u32)dev->mmio_base;
np->ram_ba = (u32)dev->ram_base;
np->s.ioaddr = dev->s.ioaddr;
np->s.ramaddr = dev->s.ramaddr;
/*
* Edit its name.
*/
strscpy(np->s.chip_name, dev->chip.name, sizeof(np->s.chip_name));
sprintf(np->s.inst_name, "sym%d", np->s.unit);
if ((SYM_CONF_DMA_ADDRESSING_MODE > 0) && (np->features & FE_DAC) &&
!dma_set_mask(&pdev->dev, DMA_DAC_MASK)) {
set_dac(np);
} else if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32))) {
printf_warning("%s: No suitable DMA available\n", sym_name(np));
goto attach_failed;
}
if (sym_hcb_attach(shost, fw, dev->nvram))
goto attach_failed;
/*
* Install the interrupt handler.
* If we synchonize the C code with SCRIPTS on interrupt,
* we do not want to share the INTR line at all.
*/
if (request_irq(pdev->irq, sym53c8xx_intr, IRQF_SHARED, NAME53C8XX,
shost)) {
printf_err("%s: request irq %u failure\n",
sym_name(np), pdev->irq);
goto attach_failed;
}
do_free_irq = 1;
/*
* After SCSI devices have been opened, we cannot
* reset the bus safely, so we do it here.
*/
spin_lock_irqsave(shost->host_lock, flags);
if (sym_reset_scsi_bus(np, 0))
goto reset_failed;
/*
* Start the SCRIPTS.
*/
sym_start_up(shost, 1);
/*
* Start the timer daemon
*/
timer_setup(&np->s.timer, sym53c8xx_timer, 0);
np->s.lasttime=0;
sym_timer (np);
/*
* Fill Linux host instance structure
* and return success.
*/
shost->max_channel = 0;
shost->this_id = np->myaddr;
shost->max_id = np->maxwide ? 16 : 8;
shost->max_lun = SYM_CONF_MAX_LUN;
shost->unique_id = pci_resource_start(pdev, 0);
shost->cmd_per_lun = SYM_CONF_MAX_TAG;
shost->can_queue = (SYM_CONF_MAX_START-2);
shost->sg_tablesize = SYM_CONF_MAX_SG;
shost->max_cmd_len = 16;
BUG_ON(sym2_transport_template == NULL);
shost->transportt = sym2_transport_template;
/* 53c896 rev 1 errata: DMA may not cross 16MB boundary */
if (pdev->device == PCI_DEVICE_ID_NCR_53C896 && pdev->revision < 2)
shost->dma_boundary = 0xFFFFFF;
spin_unlock_irqrestore(shost->host_lock, flags);
return shost;
reset_failed:
printf_err("%s: FATAL ERROR: CHECK SCSI BUS - CABLES, "
"TERMINATION, DEVICE POWER etc.!\n", sym_name(np));
spin_unlock_irqrestore(shost->host_lock, flags);
attach_failed:
printf_info("sym%d: giving up ...\n", unit);
if (np)
sym_free_resources(np, pdev, do_free_irq);
else
sym_iounmap_device(dev);
if (shost)
scsi_host_put(shost);
return NULL;
}
/*
* Detect and try to read SYMBIOS and TEKRAM NVRAM.
*/
#if SYM_CONF_NVRAM_SUPPORT
static void sym_get_nvram(struct sym_device *devp, struct sym_nvram *nvp)
{
devp->nvram = nvp;
nvp->type = 0;
sym_read_nvram(devp, nvp);
}
#else
static inline void sym_get_nvram(struct sym_device *devp, struct sym_nvram *nvp)
{
}
#endif /* SYM_CONF_NVRAM_SUPPORT */
static int sym_check_supported(struct sym_device *device)
{
struct sym_chip *chip;
struct pci_dev *pdev = device->pdev;
unsigned long io_port = pci_resource_start(pdev, 0);
int i;
/*
* If user excluded this chip, do not initialize it.
* I hate this code so much. Must kill it.
*/
if (io_port) {
for (i = 0 ; i < 8 ; i++) {
if (sym_driver_setup.excludes[i] == io_port)
return -ENODEV;
}
}
/*
* Check if the chip is supported. Then copy the chip description
* to our device structure so we can make it match the actual device
* and options.
*/
chip = sym_lookup_chip_table(pdev->device, pdev->revision);
if (!chip) {
dev_info(&pdev->dev, "device not supported\n");
return -ENODEV;
}
memcpy(&device->chip, chip, sizeof(device->chip));
return 0;
}
/*
* Ignore Symbios chips controlled by various RAID controllers.
* These controllers set value 0x52414944 at RAM end - 16.
*/
static int sym_check_raid(struct sym_device *device)
{
unsigned int ram_size, ram_val;
if (!device->s.ramaddr)
return 0;
if (device->chip.features & FE_RAM8K)
ram_size = 8192;
else
ram_size = 4096;
ram_val = readl(device->s.ramaddr + ram_size - 16);
if (ram_val != 0x52414944)
return 0;
dev_info(&device->pdev->dev,
"not initializing, driven by RAID controller.\n");
return -ENODEV;
}
static int sym_set_workarounds(struct sym_device *device)
{
struct sym_chip *chip = &device->chip;
struct pci_dev *pdev = device->pdev;
u_short status_reg;
/*
* (ITEM 12 of a DEL about the 896 I haven't yet).
* We must ensure the chip will use WRITE AND INVALIDATE.
* The revision number limit is for now arbitrary.
*/
if (pdev->device == PCI_DEVICE_ID_NCR_53C896 && pdev->revision < 0x4) {
chip->features |= (FE_WRIE | FE_CLSE);
}
/* If the chip can do Memory Write Invalidate, enable it */
if (chip->features & FE_WRIE) {
if (pci_set_mwi(pdev))
return -ENODEV;
}
/*
* Work around for errant bit in 895A. The 66Mhz
* capable bit is set erroneously. Clear this bit.
* (Item 1 DEL 533)
*
* Make sure Config space and Features agree.
*
* Recall: writes are not normal to status register -
* write a 1 to clear and a 0 to leave unchanged.
* Can only reset bits.
*/
pci_read_config_word(pdev, PCI_STATUS, &status_reg);
if (chip->features & FE_66MHZ) {
if (!(status_reg & PCI_STATUS_66MHZ))
chip->features &= ~FE_66MHZ;
} else {
if (status_reg & PCI_STATUS_66MHZ) {
status_reg = PCI_STATUS_66MHZ;
pci_write_config_word(pdev, PCI_STATUS, status_reg);
pci_read_config_word(pdev, PCI_STATUS, &status_reg);
}
}
return 0;
}
/*
* Map HBA registers and on-chip SRAM (if present).
*/
static int sym_iomap_device(struct sym_device *device)
{
struct pci_dev *pdev = device->pdev;
struct pci_bus_region bus_addr;
int i = 2;
pcibios_resource_to_bus(pdev->bus, &bus_addr, &pdev->resource[1]);
device->mmio_base = bus_addr.start;
if (device->chip.features & FE_RAM) {
/*
* If the BAR is 64-bit, resource 2 will be occupied by the
* upper 32 bits
*/
if (!pdev->resource[i].flags)
i++;
pcibios_resource_to_bus(pdev->bus, &bus_addr,
&pdev->resource[i]);
device->ram_base = bus_addr.start;
}
#ifdef CONFIG_SCSI_SYM53C8XX_MMIO
if (device->mmio_base)
device->s.ioaddr = pci_iomap(pdev, 1,
pci_resource_len(pdev, 1));
#endif
if (!device->s.ioaddr)
device->s.ioaddr = pci_iomap(pdev, 0,
pci_resource_len(pdev, 0));
if (!device->s.ioaddr) {
dev_err(&pdev->dev, "could not map registers; giving up.\n");
return -EIO;
}
if (device->ram_base) {
device->s.ramaddr = pci_iomap(pdev, i,
pci_resource_len(pdev, i));
if (!device->s.ramaddr) {
dev_warn(&pdev->dev,
"could not map SRAM; continuing anyway.\n");
device->ram_base = 0;
}
}
return 0;
}
/*
* The NCR PQS and PDS cards are constructed as a DEC bridge
* behind which sits a proprietary NCR memory controller and
* either four or two 53c875s as separate devices. We can tell
* if an 875 is part of a PQS/PDS or not since if it is, it will
* be on the same bus as the memory controller. In its usual
* mode of operation, the 875s are slaved to the memory
* controller for all transfers. To operate with the Linux
* driver, the memory controller is disabled and the 875s
* freed to function independently. The only wrinkle is that
* the preset SCSI ID (which may be zero) must be read in from
* a special configuration space register of the 875.
*/
static void sym_config_pqs(struct pci_dev *pdev, struct sym_device *sym_dev)
{
int slot;
u8 tmp;
for (slot = 0; slot < 256; slot++) {
struct pci_dev *memc = pci_get_slot(pdev->bus, slot);
if (!memc || memc->vendor != 0x101a || memc->device == 0x0009) {
pci_dev_put(memc);
continue;
}
/* bit 1: allow individual 875 configuration */
pci_read_config_byte(memc, 0x44, &tmp);
if ((tmp & 0x2) == 0) {
tmp |= 0x2;
pci_write_config_byte(memc, 0x44, tmp);
}
/* bit 2: drive individual 875 interrupts to the bus */
pci_read_config_byte(memc, 0x45, &tmp);
if ((tmp & 0x4) == 0) {
tmp |= 0x4;
pci_write_config_byte(memc, 0x45, tmp);
}
pci_dev_put(memc);
break;
}
pci_read_config_byte(pdev, 0x84, &tmp);
sym_dev->host_id = tmp;
}
/*
* Called before unloading the module.
* Detach the host.
* We have to free resources and halt the NCR chip.
*/
static int sym_detach(struct Scsi_Host *shost, struct pci_dev *pdev)
{
struct sym_hcb *np = sym_get_hcb(shost);
printk("%s: detaching ...\n", sym_name(np));
del_timer_sync(&np->s.timer);
/*
* Reset NCR chip.
* We should use sym_soft_reset(), but we don't want to do
* so, since we may not be safe if interrupts occur.
*/
printk("%s: resetting chip\n", sym_name(np));
OUTB(np, nc_istat, SRST);
INB(np, nc_mbox1);
udelay(10);
OUTB(np, nc_istat, 0);
sym_free_resources(np, pdev, 1);
scsi_host_put(shost);
return 1;
}
/*
* Driver host template.
*/
static const struct scsi_host_template sym2_template = {
.module = THIS_MODULE,
.name = "sym53c8xx",
.info = sym53c8xx_info,
.cmd_size = sizeof(struct sym_ucmd),
.queuecommand = sym53c8xx_queue_command,
.slave_alloc = sym53c8xx_slave_alloc,
.slave_configure = sym53c8xx_slave_configure,
.slave_destroy = sym53c8xx_slave_destroy,
.eh_abort_handler = sym53c8xx_eh_abort_handler,
.eh_target_reset_handler = sym53c8xx_eh_target_reset_handler,
.eh_bus_reset_handler = sym53c8xx_eh_bus_reset_handler,
.eh_host_reset_handler = sym53c8xx_eh_host_reset_handler,
.this_id = 7,
.max_sectors = 0xFFFF,
#ifdef SYM_LINUX_PROC_INFO_SUPPORT
.show_info = sym_show_info,
#ifdef SYM_LINUX_USER_COMMAND_SUPPORT
.write_info = sym_user_command,
#endif
.proc_name = NAME53C8XX,
#endif
};
static int attach_count;
static int sym2_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
struct sym_device sym_dev;
struct sym_nvram nvram;
struct Scsi_Host *shost;
int do_iounmap = 0;
int do_disable_device = 1;
memset(&sym_dev, 0, sizeof(sym_dev));
memset(&nvram, 0, sizeof(nvram));
sym_dev.pdev = pdev;
sym_dev.host_id = SYM_SETUP_HOST_ID;
if (pci_enable_device(pdev))
goto leave;
pci_set_master(pdev);
if (pci_request_regions(pdev, NAME53C8XX))
goto disable;
if (sym_check_supported(&sym_dev))
goto free;
if (sym_iomap_device(&sym_dev))
goto free;
do_iounmap = 1;
if (sym_check_raid(&sym_dev)) {
do_disable_device = 0; /* Don't disable the device */
goto free;
}
if (sym_set_workarounds(&sym_dev))
goto free;
sym_config_pqs(pdev, &sym_dev);
sym_get_nvram(&sym_dev, &nvram);
do_iounmap = 0; /* Don't sym_iounmap_device() after sym_attach(). */
shost = sym_attach(&sym2_template, attach_count, &sym_dev);
if (!shost)
goto free;
if (scsi_add_host(shost, &pdev->dev))
goto detach;
scsi_scan_host(shost);
attach_count++;
return 0;
detach:
sym_detach(pci_get_drvdata(pdev), pdev);
free:
if (do_iounmap)
sym_iounmap_device(&sym_dev);
pci_release_regions(pdev);
disable:
if (do_disable_device)
pci_disable_device(pdev);
leave:
return -ENODEV;
}
static void sym2_remove(struct pci_dev *pdev)
{
struct Scsi_Host *shost = pci_get_drvdata(pdev);
scsi_remove_host(shost);
sym_detach(shost, pdev);
pci_release_regions(pdev);
pci_disable_device(pdev);
attach_count--;
}
/**
* sym2_io_error_detected() - called when PCI error is detected
* @pdev: pointer to PCI device
* @state: current state of the PCI slot
*/
static pci_ers_result_t sym2_io_error_detected(struct pci_dev *pdev,
pci_channel_state_t state)
{
/* If slot is permanently frozen, turn everything off */
if (state == pci_channel_io_perm_failure) {
sym2_remove(pdev);
return PCI_ERS_RESULT_DISCONNECT;
}
disable_irq(pdev->irq);
pci_disable_device(pdev);
/* Request that MMIO be enabled, so register dump can be taken. */
return PCI_ERS_RESULT_CAN_RECOVER;
}
/**
* sym2_io_slot_dump - Enable MMIO and dump debug registers
* @pdev: pointer to PCI device
*/
static pci_ers_result_t sym2_io_slot_dump(struct pci_dev *pdev)
{
struct Scsi_Host *shost = pci_get_drvdata(pdev);
sym_dump_registers(shost);
/* Request a slot reset. */
return PCI_ERS_RESULT_NEED_RESET;
}
/**
* sym2_reset_workarounds - hardware-specific work-arounds
* @pdev: pointer to PCI device
*
* This routine is similar to sym_set_workarounds(), except
* that, at this point, we already know that the device was
* successfully initialized at least once before, and so most
* of the steps taken there are un-needed here.
*/
static void sym2_reset_workarounds(struct pci_dev *pdev)
{
u_short status_reg;
struct sym_chip *chip;
chip = sym_lookup_chip_table(pdev->device, pdev->revision);
/* Work around for errant bit in 895A, in a fashion
* similar to what is done in sym_set_workarounds().
*/
pci_read_config_word(pdev, PCI_STATUS, &status_reg);
if (!(chip->features & FE_66MHZ) && (status_reg & PCI_STATUS_66MHZ)) {
status_reg = PCI_STATUS_66MHZ;
pci_write_config_word(pdev, PCI_STATUS, status_reg);
pci_read_config_word(pdev, PCI_STATUS, &status_reg);
}
}
/**
* sym2_io_slot_reset() - called when the pci bus has been reset.
* @pdev: pointer to PCI device
*
* Restart the card from scratch.
*/
static pci_ers_result_t sym2_io_slot_reset(struct pci_dev *pdev)
{
struct Scsi_Host *shost = pci_get_drvdata(pdev);
struct sym_hcb *np = sym_get_hcb(shost);
printk(KERN_INFO "%s: recovering from a PCI slot reset\n",
sym_name(np));
if (pci_enable_device(pdev)) {
printk(KERN_ERR "%s: Unable to enable after PCI reset\n",
sym_name(np));
return PCI_ERS_RESULT_DISCONNECT;
}
pci_set_master(pdev);
enable_irq(pdev->irq);
/* If the chip can do Memory Write Invalidate, enable it */
if (np->features & FE_WRIE) {
if (pci_set_mwi(pdev))
return PCI_ERS_RESULT_DISCONNECT;
}
/* Perform work-arounds, analogous to sym_set_workarounds() */
sym2_reset_workarounds(pdev);
/* Perform host reset only on one instance of the card */
if (PCI_FUNC(pdev->devfn) == 0) {
if (sym_reset_scsi_bus(np, 0)) {
printk(KERN_ERR "%s: Unable to reset scsi host\n",
sym_name(np));
return PCI_ERS_RESULT_DISCONNECT;
}
sym_start_up(shost, 1);
}
return PCI_ERS_RESULT_RECOVERED;
}
/**
* sym2_io_resume() - resume normal ops after PCI reset
* @pdev: pointer to PCI device
*
* Called when the error recovery driver tells us that its
* OK to resume normal operation. Use completion to allow
* halted scsi ops to resume.
*/
static void sym2_io_resume(struct pci_dev *pdev)
{
struct Scsi_Host *shost = pci_get_drvdata(pdev);
struct sym_data *sym_data = shost_priv(shost);
spin_lock_irq(shost->host_lock);
if (sym_data->io_reset)
complete(sym_data->io_reset);
spin_unlock_irq(shost->host_lock);
}
static void sym2_get_signalling(struct Scsi_Host *shost)
{
struct sym_hcb *np = sym_get_hcb(shost);
enum spi_signal_type type;
switch (np->scsi_mode) {
case SMODE_SE:
type = SPI_SIGNAL_SE;
break;
case SMODE_LVD:
type = SPI_SIGNAL_LVD;
break;
case SMODE_HVD:
type = SPI_SIGNAL_HVD;
break;
default:
type = SPI_SIGNAL_UNKNOWN;
break;
}
spi_signalling(shost) = type;
}
static void sym2_set_offset(struct scsi_target *starget, int offset)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
tp->tgoal.offset = offset;
tp->tgoal.check_nego = 1;
}
static void sym2_set_period(struct scsi_target *starget, int period)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
/* have to have DT for these transfers, but DT will also
* set width, so check that this is allowed */
if (period <= np->minsync && spi_width(starget))
tp->tgoal.dt = 1;
tp->tgoal.period = period;
tp->tgoal.check_nego = 1;
}
static void sym2_set_width(struct scsi_target *starget, int width)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
/* It is illegal to have DT set on narrow transfers. If DT is
* clear, we must also clear IU and QAS. */
if (width == 0)
tp->tgoal.iu = tp->tgoal.dt = tp->tgoal.qas = 0;
tp->tgoal.width = width;
tp->tgoal.check_nego = 1;
}
static void sym2_set_dt(struct scsi_target *starget, int dt)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
/* We must clear QAS and IU if DT is clear */
if (dt)
tp->tgoal.dt = 1;
else
tp->tgoal.iu = tp->tgoal.dt = tp->tgoal.qas = 0;
tp->tgoal.check_nego = 1;
}
#if 0
static void sym2_set_iu(struct scsi_target *starget, int iu)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
if (iu)
tp->tgoal.iu = tp->tgoal.dt = 1;
else
tp->tgoal.iu = 0;
tp->tgoal.check_nego = 1;
}
static void sym2_set_qas(struct scsi_target *starget, int qas)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct sym_hcb *np = sym_get_hcb(shost);
struct sym_tcb *tp = &np->target[starget->id];
if (qas)
tp->tgoal.dt = tp->tgoal.qas = 1;
else
tp->tgoal.qas = 0;
tp->tgoal.check_nego = 1;
}
#endif
static struct spi_function_template sym2_transport_functions = {
.set_offset = sym2_set_offset,
.show_offset = 1,
.set_period = sym2_set_period,
.show_period = 1,
.set_width = sym2_set_width,
.show_width = 1,
.set_dt = sym2_set_dt,
.show_dt = 1,
#if 0
.set_iu = sym2_set_iu,
.show_iu = 1,
.set_qas = sym2_set_qas,
.show_qas = 1,
#endif
.get_signalling = sym2_get_signalling,
};
static struct pci_device_id sym2_id_table[] = {
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C810,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C820,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL }, /* new */
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C825,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C815,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C810AP,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL }, /* new */
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C860,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1510,
PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_SCSI<<8, 0xffff00, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C896,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C895,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C885,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C875,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C1510,
PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_SCSI<<8, 0xffff00, 0UL }, /* new */
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C895A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C875A,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1010_33,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_LSI_53C1010_66,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ PCI_VENDOR_ID_LSI_LOGIC, PCI_DEVICE_ID_NCR_53C875J,
PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, sym2_id_table);
static const struct pci_error_handlers sym2_err_handler = {
.error_detected = sym2_io_error_detected,
.mmio_enabled = sym2_io_slot_dump,
.slot_reset = sym2_io_slot_reset,
.resume = sym2_io_resume,
};
static struct pci_driver sym2_driver = {
.name = NAME53C8XX,
.id_table = sym2_id_table,
.probe = sym2_probe,
.remove = sym2_remove,
.err_handler = &sym2_err_handler,
};
static int __init sym2_init(void)
{
int error;
sym2_setup_params();
sym2_transport_template = spi_attach_transport(&sym2_transport_functions);
if (!sym2_transport_template)
return -ENODEV;
error = pci_register_driver(&sym2_driver);
if (error)
spi_release_transport(sym2_transport_template);
return error;
}
static void __exit sym2_exit(void)
{
pci_unregister_driver(&sym2_driver);
spi_release_transport(sym2_transport_template);
}
module_init(sym2_init);
module_exit(sym2_exit);
Codebase Browser
linux