/* SPDX-License-Identifier: GPL-2.0 */
/*
* ChromeOS Embedded Controller protocol interface.
*
* Copyright (C) 2012 Google, Inc
*/
#ifndef __LINUX_CROS_EC_PROTO_H
#define __LINUX_CROS_EC_PROTO_H
#include <linux/device.h>
#include <linux/lockdep_types.h>
#include <linux/mutex.h>
#include <linux/notifier.h>
#include <linux/platform_data/cros_ec_commands.h>
#define CROS_EC_DEV_NAME "cros_ec"
#define CROS_EC_DEV_FP_NAME "cros_fp"
#define CROS_EC_DEV_ISH_NAME "cros_ish"
#define CROS_EC_DEV_PD_NAME "cros_pd"
#define CROS_EC_DEV_SCP_NAME "cros_scp"
#define CROS_EC_DEV_TP_NAME "cros_tp"
#define CROS_EC_DEV_EC_INDEX 0
#define CROS_EC_DEV_PD_INDEX 1
/*
* The EC is unresponsive for a time after a reboot command. Add a
* simple delay to make sure that the bus stays locked.
*/
#define EC_REBOOT_DELAY_MS 50
/*
* Max bus-specific overhead incurred by request/responses.
* I2C requires 1 additional byte for requests.
* I2C requires 2 additional bytes for responses.
* SPI requires up to 32 additional bytes for responses.
*/
#define EC_PROTO_VERSION_UNKNOWN 0
#define EC_MAX_REQUEST_OVERHEAD 1
#define EC_MAX_RESPONSE_OVERHEAD 32
/*
* EC panic is not covered by the standard (0-F) ACPI notify values.
* Arbitrarily choosing B0 to notify ec panic, which is in the 84-BF
* device specific ACPI notify range.
*/
#define ACPI_NOTIFY_CROS_EC_PANIC 0xB0
/*
* Command interface between EC and AP, for LPC, I2C and SPI interfaces.
*/
enum {
EC_MSG_TX_HEADER_BYTES = 3,
EC_MSG_TX_TRAILER_BYTES = 1,
EC_MSG_TX_PROTO_BYTES = EC_MSG_TX_HEADER_BYTES +
EC_MSG_TX_TRAILER_BYTES,
EC_MSG_RX_PROTO_BYTES = 3,
/* Max length of messages for proto 2*/
EC_PROTO2_MSG_BYTES = EC_PROTO2_MAX_PARAM_SIZE +
EC_MSG_TX_PROTO_BYTES,
EC_MAX_MSG_BYTES = 64 * 1024,
};
/**
* struct cros_ec_command - Information about a ChromeOS EC command.
* @version: Command version number (often 0).
* @command: Command to send (EC_CMD_...).
* @outsize: Outgoing length in bytes.
* @insize: Max number of bytes to accept from the EC.
* @result: EC's response to the command (separate from communication failure).
* @data: Where to put the incoming data from EC and outgoing data to EC.
*/
struct cros_ec_command {
uint32_t version;
uint32_t command;
uint32_t outsize;
uint32_t insize;
uint32_t result;
uint8_t data[];
};
/**
* struct cros_ec_device - Information about a ChromeOS EC device.
* @phys_name: Name of physical comms layer (e.g. 'i2c-4').
* @dev: Device pointer for physical comms device
* @cros_class: The class structure for this device.
* @cmd_readmem: Direct read of the EC memory-mapped region, if supported.
* @offset: Is within EC_LPC_ADDR_MEMMAP region.
* @bytes: Number of bytes to read. zero means "read a string" (including
* the trailing '\0'). At most only EC_MEMMAP_SIZE bytes can be
* read. Caller must ensure that the buffer is large enough for the
* result when reading a string.
* @max_request: Max size of message requested.
* @max_response: Max size of message response.
* @max_passthru: Max sice of passthru message.
* @proto_version: The protocol version used for this device.
* @priv: Private data.
* @irq: Interrupt to use.
* @id: Device id.
* @din: Input buffer (for data from EC). This buffer will always be
* dword-aligned and include enough space for up to 7 word-alignment
* bytes also, so we can ensure that the body of the message is always
* dword-aligned (64-bit). We use this alignment to keep ARM and x86
* happy. Probably word alignment would be OK, there might be a small
* performance advantage to using dword.
* @dout: Output buffer (for data to EC). This buffer will always be
* dword-aligned and include enough space for up to 7 word-alignment
* bytes also, so we can ensure that the body of the message is always
* dword-aligned (64-bit). We use this alignment to keep ARM and x86
* happy. Probably word alignment would be OK, there might be a small
* performance advantage to using dword.
* @din_size: Size of din buffer to allocate (zero to use static din).
* @dout_size: Size of dout buffer to allocate (zero to use static dout).
* @wake_enabled: True if this device can wake the system from sleep.
* @suspended: True if this device had been suspended.
* @cmd_xfer: Send command to EC and get response.
* Returns the number of bytes received if the communication
* succeeded, but that doesn't mean the EC was happy with the
* command. The caller should check msg.result for the EC's result
* code.
* @pkt_xfer: Send packet to EC and get response.
* @lockdep_key: Lockdep class for each instance. Unused if CONFIG_LOCKDEP is
* not enabled.
* @lock: One transaction at a time.
* @mkbp_event_supported: 0 if MKBP not supported. Otherwise its value is
* the maximum supported version of the MKBP host event
* command + 1.
* @host_sleep_v1: True if this EC supports the sleep v1 command.
* @event_notifier: Interrupt event notifier for transport devices.
* @event_data: Raw payload transferred with the MKBP event.
* @event_size: Size in bytes of the event data.
* @host_event_wake_mask: Mask of host events that cause wake from suspend.
* @suspend_timeout_ms: The timeout in milliseconds between when sleep event
* is received and when the EC will declare sleep
* transition failure if the sleep signal is not
* asserted. See also struct
* ec_params_host_sleep_event_v1 in cros_ec_commands.h.
* @last_resume_result: The number of sleep power signal transitions that
* occurred since the suspend message. The high bit
* indicates a timeout occurred. See also struct
* ec_response_host_sleep_event_v1 in cros_ec_commands.h.
* @last_event_time: exact time from the hard irq when we got notified of
* a new event.
* @notifier_ready: The notifier_block to let the kernel re-query EC
* communication protocol when the EC sends
* EC_HOST_EVENT_INTERFACE_READY.
* @ec: The platform_device used by the mfd driver to interface with the
* main EC.
* @pd: The platform_device used by the mfd driver to interface with the
* PD behind an EC.
* @panic_notifier: EC panic notifier.
*/
struct cros_ec_device {
/* These are used by other drivers that want to talk to the EC */
const char *phys_name;
struct device *dev;
struct class *cros_class;
int (*cmd_readmem)(struct cros_ec_device *ec, unsigned int offset,
unsigned int bytes, void *dest);
/* These are used to implement the platform-specific interface */
u16 max_request;
u16 max_response;
u16 max_passthru;
u16 proto_version;
void *priv;
int irq;
u8 *din;
u8 *dout;
int din_size;
int dout_size;
bool wake_enabled;
bool suspended;
int (*cmd_xfer)(struct cros_ec_device *ec,
struct cros_ec_command *msg);
int (*pkt_xfer)(struct cros_ec_device *ec,
struct cros_ec_command *msg);
struct lock_class_key lockdep_key;
struct mutex lock;
u8 mkbp_event_supported;
bool host_sleep_v1;
struct blocking_notifier_head event_notifier;
struct ec_response_get_next_event_v3 event_data;
int event_size;
u32 host_event_wake_mask;
u32 last_resume_result;
u16 suspend_timeout_ms;
ktime_t last_event_time;
struct notifier_block notifier_ready;
/* The platform devices used by the mfd driver */
struct platform_device *ec;
struct platform_device *pd;
struct blocking_notifier_head panic_notifier;
};
/**
* struct cros_ec_platform - ChromeOS EC platform information.
* @ec_name: Name of EC device (e.g. 'cros-ec', 'cros-pd', ...)
* used in /dev/ and sysfs.
* @cmd_offset: Offset to apply for each command. Set when
* registering a device behind another one.
*/
struct cros_ec_platform {
const char *ec_name;
u16 cmd_offset;
};
/**
* struct cros_ec_dev - ChromeOS EC device entry point.
* @class_dev: Device structure used in sysfs.
* @ec_dev: cros_ec_device structure to talk to the physical device.
* @dev: Pointer to the platform device.
* @debug_info: cros_ec_debugfs structure for debugging information.
* @has_kb_wake_angle: True if at least 2 accelerometer are connected to the EC.
* @cmd_offset: Offset to apply for each command.
* @features: Features supported by the EC.
*/
struct cros_ec_dev {
struct device class_dev;
struct cros_ec_device *ec_dev;
struct device *dev;
struct cros_ec_debugfs *debug_info;
bool has_kb_wake_angle;
u16 cmd_offset;
struct ec_response_get_features features;
};
#define to_cros_ec_dev(dev) container_of(dev, struct cros_ec_dev, class_dev)
int cros_ec_prepare_tx(struct cros_ec_device *ec_dev,
struct cros_ec_command *msg);
int cros_ec_check_result(struct cros_ec_device *ec_dev,
struct cros_ec_command *msg);
int cros_ec_cmd_xfer(struct cros_ec_device *ec_dev,
struct cros_ec_command *msg);
int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
struct cros_ec_command *msg);
int cros_ec_query_all(struct cros_ec_device *ec_dev);
int cros_ec_get_next_event(struct cros_ec_device *ec_dev,
bool *wake_event,
bool *has_more_events);
u32 cros_ec_get_host_event(struct cros_ec_device *ec_dev);
bool cros_ec_check_features(struct cros_ec_dev *ec, int feature);
int cros_ec_get_sensor_count(struct cros_ec_dev *ec);
int cros_ec_cmd(struct cros_ec_device *ec_dev, unsigned int version, int command, const void *outdata,
size_t outsize, void *indata, size_t insize);
int cros_ec_cmd_readmem(struct cros_ec_device *ec_dev, u8 offset, u8 size, void *dest);
int cros_ec_get_cmd_versions(struct cros_ec_device *ec_dev, u16 cmd);
/**
* cros_ec_get_time_ns() - Return time in ns.
*
* This is the function used to record the time for last_event_time in struct
* cros_ec_device during the hard irq.
*
* Return: ktime_t format since boot.
*/
static inline ktime_t cros_ec_get_time_ns(void)
{
return ktime_get_boottime_ns();
}
#endif /* __LINUX_CROS_EC_PROTO_H */
Codebase Browser
linux