// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 1999 - 2018 Intel Corporation. */
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/netdevice.h>
#include "ixgbe.h"
#include "ixgbe_common.h"
#include "ixgbe_phy.h"
static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw);
static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw);
static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw);
static int ixgbe_ready_eeprom(struct ixgbe_hw *hw);
static void ixgbe_standby_eeprom(struct ixgbe_hw *hw);
static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
u16 count);
static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count);
static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec);
static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data);
static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data);
static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
u16 offset);
static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw);
/* Base table for registers values that change by MAC */
const u32 ixgbe_mvals_8259X[IXGBE_MVALS_IDX_LIMIT] = {
IXGBE_MVALS_INIT(8259X)
};
/**
* ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
* control
* @hw: pointer to hardware structure
*
* There are several phys that do not support autoneg flow control. This
* function check the device id to see if the associated phy supports
* autoneg flow control.
**/
bool ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
{
bool supported = false;
ixgbe_link_speed speed;
bool link_up;
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
/* flow control autoneg black list */
switch (hw->device_id) {
case IXGBE_DEV_ID_X550EM_A_SFP:
case IXGBE_DEV_ID_X550EM_A_SFP_N:
supported = false;
break;
default:
hw->mac.ops.check_link(hw, &speed, &link_up, false);
/* if link is down, assume supported */
if (link_up)
supported = speed == IXGBE_LINK_SPEED_1GB_FULL;
else
supported = true;
}
break;
case ixgbe_media_type_backplane:
if (hw->device_id == IXGBE_DEV_ID_X550EM_X_XFI)
supported = false;
else
supported = true;
break;
case ixgbe_media_type_copper:
/* only some copper devices support flow control autoneg */
switch (hw->device_id) {
case IXGBE_DEV_ID_82599_T3_LOM:
case IXGBE_DEV_ID_X540T:
case IXGBE_DEV_ID_X540T1:
case IXGBE_DEV_ID_X550T:
case IXGBE_DEV_ID_X550T1:
case IXGBE_DEV_ID_X550EM_X_10G_T:
case IXGBE_DEV_ID_X550EM_A_10G_T:
case IXGBE_DEV_ID_X550EM_A_1G_T:
case IXGBE_DEV_ID_X550EM_A_1G_T_L:
supported = true;
break;
default:
break;
}
break;
default:
break;
}
if (!supported)
hw_dbg(hw, "Device %x does not support flow control autoneg\n",
hw->device_id);
return supported;
}
/**
* ixgbe_setup_fc_generic - Set up flow control
* @hw: pointer to hardware structure
*
* Called at init time to set up flow control.
**/
int ixgbe_setup_fc_generic(struct ixgbe_hw *hw)
{
u32 reg = 0, reg_bp = 0;
bool locked = false;
int ret_val = 0;
u16 reg_cu = 0;
/*
* Validate the requested mode. Strict IEEE mode does not allow
* ixgbe_fc_rx_pause because it will cause us to fail at UNH.
*/
if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
return -EINVAL;
}
/*
* 10gig parts do not have a word in the EEPROM to determine the
* default flow control setting, so we explicitly set it to full.
*/
if (hw->fc.requested_mode == ixgbe_fc_default)
hw->fc.requested_mode = ixgbe_fc_full;
/*
* Set up the 1G and 10G flow control advertisement registers so the
* HW will be able to do fc autoneg once the cable is plugged in. If
* we link at 10G, the 1G advertisement is harmless and vice versa.
*/
switch (hw->phy.media_type) {
case ixgbe_media_type_backplane:
/* some MAC's need RMW protection on AUTOC */
ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, ®_bp);
if (ret_val)
return ret_val;
fallthrough; /* only backplane uses autoc */
case ixgbe_media_type_fiber:
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
break;
case ixgbe_media_type_copper:
hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
MDIO_MMD_AN, ®_cu);
break;
default:
break;
}
/*
* The possible values of fc.requested_mode are:
* 0: Flow control is completely disabled
* 1: Rx flow control is enabled (we can receive pause frames,
* but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames but
* we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: Invalid.
*/
switch (hw->fc.requested_mode) {
case ixgbe_fc_none:
/* Flow control completely disabled by software override. */
reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
if (hw->phy.media_type == ixgbe_media_type_backplane)
reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
IXGBE_AUTOC_ASM_PAUSE);
else if (hw->phy.media_type == ixgbe_media_type_copper)
reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
break;
case ixgbe_fc_tx_pause:
/*
* Tx Flow control is enabled, and Rx Flow control is
* disabled by software override.
*/
reg |= IXGBE_PCS1GANA_ASM_PAUSE;
reg &= ~IXGBE_PCS1GANA_SYM_PAUSE;
if (hw->phy.media_type == ixgbe_media_type_backplane) {
reg_bp |= IXGBE_AUTOC_ASM_PAUSE;
reg_bp &= ~IXGBE_AUTOC_SYM_PAUSE;
} else if (hw->phy.media_type == ixgbe_media_type_copper) {
reg_cu |= IXGBE_TAF_ASM_PAUSE;
reg_cu &= ~IXGBE_TAF_SYM_PAUSE;
}
break;
case ixgbe_fc_rx_pause:
/*
* Rx Flow control is enabled and Tx Flow control is
* disabled by software override. Since there really
* isn't a way to advertise that we are capable of RX
* Pause ONLY, we will advertise that we support both
* symmetric and asymmetric Rx PAUSE, as such we fall
* through to the fc_full statement. Later, we will
* disable the adapter's ability to send PAUSE frames.
*/
case ixgbe_fc_full:
/* Flow control (both Rx and Tx) is enabled by SW override. */
reg |= IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE;
if (hw->phy.media_type == ixgbe_media_type_backplane)
reg_bp |= IXGBE_AUTOC_SYM_PAUSE |
IXGBE_AUTOC_ASM_PAUSE;
else if (hw->phy.media_type == ixgbe_media_type_copper)
reg_cu |= IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE;
break;
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
return -EIO;
}
if (hw->mac.type != ixgbe_mac_X540) {
/*
* Enable auto-negotiation between the MAC & PHY;
* the MAC will advertise clause 37 flow control.
*/
IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
/* Disable AN timeout */
if (hw->fc.strict_ieee)
reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
}
/*
* AUTOC restart handles negotiation of 1G and 10G on backplane
* and copper. There is no need to set the PCS1GCTL register.
*
*/
if (hw->phy.media_type == ixgbe_media_type_backplane) {
/* Need the SW/FW semaphore around AUTOC writes if 82599 and
* LESM is on, likewise reset_pipeline requries the lock as
* it also writes AUTOC.
*/
ret_val = hw->mac.ops.prot_autoc_write(hw, reg_bp, locked);
if (ret_val)
return ret_val;
} else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
ixgbe_device_supports_autoneg_fc(hw)) {
hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
MDIO_MMD_AN, reg_cu);
}
hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
return ret_val;
}
/**
* ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
* @hw: pointer to hardware structure
*
* Starts the hardware by filling the bus info structure and media type, clears
* all on chip counters, initializes receive address registers, multicast
* table, VLAN filter table, calls routine to set up link and flow control
* settings, and leaves transmit and receive units disabled and uninitialized
**/
int ixgbe_start_hw_generic(struct ixgbe_hw *hw)
{
u16 device_caps;
u32 ctrl_ext;
int ret_val;
/* Set the media type */
hw->phy.media_type = hw->mac.ops.get_media_type(hw);
/* Identify the PHY */
hw->phy.ops.identify(hw);
/* Clear the VLAN filter table */
hw->mac.ops.clear_vfta(hw);
/* Clear statistics registers */
hw->mac.ops.clear_hw_cntrs(hw);
/* Set No Snoop Disable */
ctrl_ext = IXGBE_READ_REG(hw, IXGBE_CTRL_EXT);
ctrl_ext |= IXGBE_CTRL_EXT_NS_DIS;
IXGBE_WRITE_REG(hw, IXGBE_CTRL_EXT, ctrl_ext);
IXGBE_WRITE_FLUSH(hw);
/* Setup flow control if method for doing so */
if (hw->mac.ops.setup_fc) {
ret_val = hw->mac.ops.setup_fc(hw);
if (ret_val)
return ret_val;
}
/* Cashe bit indicating need for crosstalk fix */
switch (hw->mac.type) {
case ixgbe_mac_82599EB:
case ixgbe_mac_X550EM_x:
case ixgbe_mac_x550em_a:
hw->mac.ops.get_device_caps(hw, &device_caps);
if (device_caps & IXGBE_DEVICE_CAPS_NO_CROSSTALK_WR)
hw->need_crosstalk_fix = false;
else
hw->need_crosstalk_fix = true;
break;
default:
hw->need_crosstalk_fix = false;
break;
}
/* Clear adapter stopped flag */
hw->adapter_stopped = false;
return 0;
}
/**
* ixgbe_start_hw_gen2 - Init sequence for common device family
* @hw: pointer to hw structure
*
* Performs the init sequence common to the second generation
* of 10 GbE devices.
* Devices in the second generation:
* 82599
* X540
**/
int ixgbe_start_hw_gen2(struct ixgbe_hw *hw)
{
u32 i;
/* Clear the rate limiters */
for (i = 0; i < hw->mac.max_tx_queues; i++) {
IXGBE_WRITE_REG(hw, IXGBE_RTTDQSEL, i);
IXGBE_WRITE_REG(hw, IXGBE_RTTBCNRC, 0);
}
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_init_hw_generic - Generic hardware initialization
* @hw: pointer to hardware structure
*
* Initialize the hardware by resetting the hardware, filling the bus info
* structure and media type, clears all on chip counters, initializes receive
* address registers, multicast table, VLAN filter table, calls routine to set
* up link and flow control settings, and leaves transmit and receive units
* disabled and uninitialized
**/
int ixgbe_init_hw_generic(struct ixgbe_hw *hw)
{
int status;
/* Reset the hardware */
status = hw->mac.ops.reset_hw(hw);
if (status == 0) {
/* Start the HW */
status = hw->mac.ops.start_hw(hw);
}
/* Initialize the LED link active for LED blink support */
if (hw->mac.ops.init_led_link_act)
hw->mac.ops.init_led_link_act(hw);
return status;
}
/**
* ixgbe_clear_hw_cntrs_generic - Generic clear hardware counters
* @hw: pointer to hardware structure
*
* Clears all hardware statistics counters by reading them from the hardware
* Statistics counters are clear on read.
**/
int ixgbe_clear_hw_cntrs_generic(struct ixgbe_hw *hw)
{
u16 i = 0;
IXGBE_READ_REG(hw, IXGBE_CRCERRS);
IXGBE_READ_REG(hw, IXGBE_ILLERRC);
IXGBE_READ_REG(hw, IXGBE_ERRBC);
IXGBE_READ_REG(hw, IXGBE_MSPDC);
for (i = 0; i < 8; i++)
IXGBE_READ_REG(hw, IXGBE_MPC(i));
IXGBE_READ_REG(hw, IXGBE_MLFC);
IXGBE_READ_REG(hw, IXGBE_MRFC);
IXGBE_READ_REG(hw, IXGBE_RLEC);
IXGBE_READ_REG(hw, IXGBE_LXONTXC);
IXGBE_READ_REG(hw, IXGBE_LXOFFTXC);
if (hw->mac.type >= ixgbe_mac_82599EB) {
IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
IXGBE_READ_REG(hw, IXGBE_LXOFFRXCNT);
} else {
IXGBE_READ_REG(hw, IXGBE_LXONRXC);
IXGBE_READ_REG(hw, IXGBE_LXOFFRXC);
}
for (i = 0; i < 8; i++) {
IXGBE_READ_REG(hw, IXGBE_PXONTXC(i));
IXGBE_READ_REG(hw, IXGBE_PXOFFTXC(i));
if (hw->mac.type >= ixgbe_mac_82599EB) {
IXGBE_READ_REG(hw, IXGBE_PXONRXCNT(i));
IXGBE_READ_REG(hw, IXGBE_PXOFFRXCNT(i));
} else {
IXGBE_READ_REG(hw, IXGBE_PXONRXC(i));
IXGBE_READ_REG(hw, IXGBE_PXOFFRXC(i));
}
}
if (hw->mac.type >= ixgbe_mac_82599EB)
for (i = 0; i < 8; i++)
IXGBE_READ_REG(hw, IXGBE_PXON2OFFCNT(i));
IXGBE_READ_REG(hw, IXGBE_PRC64);
IXGBE_READ_REG(hw, IXGBE_PRC127);
IXGBE_READ_REG(hw, IXGBE_PRC255);
IXGBE_READ_REG(hw, IXGBE_PRC511);
IXGBE_READ_REG(hw, IXGBE_PRC1023);
IXGBE_READ_REG(hw, IXGBE_PRC1522);
IXGBE_READ_REG(hw, IXGBE_GPRC);
IXGBE_READ_REG(hw, IXGBE_BPRC);
IXGBE_READ_REG(hw, IXGBE_MPRC);
IXGBE_READ_REG(hw, IXGBE_GPTC);
IXGBE_READ_REG(hw, IXGBE_GORCL);
IXGBE_READ_REG(hw, IXGBE_GORCH);
IXGBE_READ_REG(hw, IXGBE_GOTCL);
IXGBE_READ_REG(hw, IXGBE_GOTCH);
if (hw->mac.type == ixgbe_mac_82598EB)
for (i = 0; i < 8; i++)
IXGBE_READ_REG(hw, IXGBE_RNBC(i));
IXGBE_READ_REG(hw, IXGBE_RUC);
IXGBE_READ_REG(hw, IXGBE_RFC);
IXGBE_READ_REG(hw, IXGBE_ROC);
IXGBE_READ_REG(hw, IXGBE_RJC);
IXGBE_READ_REG(hw, IXGBE_MNGPRC);
IXGBE_READ_REG(hw, IXGBE_MNGPDC);
IXGBE_READ_REG(hw, IXGBE_MNGPTC);
IXGBE_READ_REG(hw, IXGBE_TORL);
IXGBE_READ_REG(hw, IXGBE_TORH);
IXGBE_READ_REG(hw, IXGBE_TPR);
IXGBE_READ_REG(hw, IXGBE_TPT);
IXGBE_READ_REG(hw, IXGBE_PTC64);
IXGBE_READ_REG(hw, IXGBE_PTC127);
IXGBE_READ_REG(hw, IXGBE_PTC255);
IXGBE_READ_REG(hw, IXGBE_PTC511);
IXGBE_READ_REG(hw, IXGBE_PTC1023);
IXGBE_READ_REG(hw, IXGBE_PTC1522);
IXGBE_READ_REG(hw, IXGBE_MPTC);
IXGBE_READ_REG(hw, IXGBE_BPTC);
for (i = 0; i < 16; i++) {
IXGBE_READ_REG(hw, IXGBE_QPRC(i));
IXGBE_READ_REG(hw, IXGBE_QPTC(i));
if (hw->mac.type >= ixgbe_mac_82599EB) {
IXGBE_READ_REG(hw, IXGBE_QBRC_L(i));
IXGBE_READ_REG(hw, IXGBE_QBRC_H(i));
IXGBE_READ_REG(hw, IXGBE_QBTC_L(i));
IXGBE_READ_REG(hw, IXGBE_QBTC_H(i));
IXGBE_READ_REG(hw, IXGBE_QPRDC(i));
} else {
IXGBE_READ_REG(hw, IXGBE_QBRC(i));
IXGBE_READ_REG(hw, IXGBE_QBTC(i));
}
}
if (hw->mac.type == ixgbe_mac_X550 || hw->mac.type == ixgbe_mac_X540) {
if (hw->phy.id == 0)
hw->phy.ops.identify(hw);
hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECL, MDIO_MMD_PCS, &i);
hw->phy.ops.read_reg(hw, IXGBE_PCRC8ECH, MDIO_MMD_PCS, &i);
hw->phy.ops.read_reg(hw, IXGBE_LDPCECL, MDIO_MMD_PCS, &i);
hw->phy.ops.read_reg(hw, IXGBE_LDPCECH, MDIO_MMD_PCS, &i);
}
return 0;
}
/**
* ixgbe_read_pba_string_generic - Reads part number string from EEPROM
* @hw: pointer to hardware structure
* @pba_num: stores the part number string from the EEPROM
* @pba_num_size: part number string buffer length
*
* Reads the part number string from the EEPROM.
**/
int ixgbe_read_pba_string_generic(struct ixgbe_hw *hw, u8 *pba_num,
u32 pba_num_size)
{
int ret_val;
u16 pba_ptr;
u16 offset;
u16 length;
u16 data;
if (pba_num == NULL) {
hw_dbg(hw, "PBA string buffer was null\n");
return -EINVAL;
}
ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM0_PTR, &data);
if (ret_val) {
hw_dbg(hw, "NVM Read Error\n");
return ret_val;
}
ret_val = hw->eeprom.ops.read(hw, IXGBE_PBANUM1_PTR, &pba_ptr);
if (ret_val) {
hw_dbg(hw, "NVM Read Error\n");
return ret_val;
}
/*
* if data is not ptr guard the PBA must be in legacy format which
* means pba_ptr is actually our second data word for the PBA number
* and we can decode it into an ascii string
*/
if (data != IXGBE_PBANUM_PTR_GUARD) {
hw_dbg(hw, "NVM PBA number is not stored as string\n");
/* we will need 11 characters to store the PBA */
if (pba_num_size < 11) {
hw_dbg(hw, "PBA string buffer too small\n");
return -ENOSPC;
}
/* extract hex string from data and pba_ptr */
pba_num[0] = (data >> 12) & 0xF;
pba_num[1] = (data >> 8) & 0xF;
pba_num[2] = (data >> 4) & 0xF;
pba_num[3] = data & 0xF;
pba_num[4] = (pba_ptr >> 12) & 0xF;
pba_num[5] = (pba_ptr >> 8) & 0xF;
pba_num[6] = '-';
pba_num[7] = 0;
pba_num[8] = (pba_ptr >> 4) & 0xF;
pba_num[9] = pba_ptr & 0xF;
/* put a null character on the end of our string */
pba_num[10] = '\0';
/* switch all the data but the '-' to hex char */
for (offset = 0; offset < 10; offset++) {
if (pba_num[offset] < 0xA)
pba_num[offset] += '0';
else if (pba_num[offset] < 0x10)
pba_num[offset] += 'A' - 0xA;
}
return 0;
}
ret_val = hw->eeprom.ops.read(hw, pba_ptr, &length);
if (ret_val) {
hw_dbg(hw, "NVM Read Error\n");
return ret_val;
}
if (length == 0xFFFF || length == 0) {
hw_dbg(hw, "NVM PBA number section invalid length\n");
return -EIO;
}
/* check if pba_num buffer is big enough */
if (pba_num_size < (((u32)length * 2) - 1)) {
hw_dbg(hw, "PBA string buffer too small\n");
return -ENOSPC;
}
/* trim pba length from start of string */
pba_ptr++;
length--;
for (offset = 0; offset < length; offset++) {
ret_val = hw->eeprom.ops.read(hw, pba_ptr + offset, &data);
if (ret_val) {
hw_dbg(hw, "NVM Read Error\n");
return ret_val;
}
pba_num[offset * 2] = (u8)(data >> 8);
pba_num[(offset * 2) + 1] = (u8)(data & 0xFF);
}
pba_num[offset * 2] = '\0';
return 0;
}
/**
* ixgbe_get_mac_addr_generic - Generic get MAC address
* @hw: pointer to hardware structure
* @mac_addr: Adapter MAC address
*
* Reads the adapter's MAC address from first Receive Address Register (RAR0)
* A reset of the adapter must be performed prior to calling this function
* in order for the MAC address to have been loaded from the EEPROM into RAR0
**/
int ixgbe_get_mac_addr_generic(struct ixgbe_hw *hw, u8 *mac_addr)
{
u32 rar_high;
u32 rar_low;
u16 i;
rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(0));
rar_low = IXGBE_READ_REG(hw, IXGBE_RAL(0));
for (i = 0; i < 4; i++)
mac_addr[i] = (u8)(rar_low >> (i*8));
for (i = 0; i < 2; i++)
mac_addr[i+4] = (u8)(rar_high >> (i*8));
return 0;
}
enum ixgbe_bus_width ixgbe_convert_bus_width(u16 link_status)
{
switch (link_status & IXGBE_PCI_LINK_WIDTH) {
case IXGBE_PCI_LINK_WIDTH_1:
return ixgbe_bus_width_pcie_x1;
case IXGBE_PCI_LINK_WIDTH_2:
return ixgbe_bus_width_pcie_x2;
case IXGBE_PCI_LINK_WIDTH_4:
return ixgbe_bus_width_pcie_x4;
case IXGBE_PCI_LINK_WIDTH_8:
return ixgbe_bus_width_pcie_x8;
default:
return ixgbe_bus_width_unknown;
}
}
enum ixgbe_bus_speed ixgbe_convert_bus_speed(u16 link_status)
{
switch (link_status & IXGBE_PCI_LINK_SPEED) {
case IXGBE_PCI_LINK_SPEED_2500:
return ixgbe_bus_speed_2500;
case IXGBE_PCI_LINK_SPEED_5000:
return ixgbe_bus_speed_5000;
case IXGBE_PCI_LINK_SPEED_8000:
return ixgbe_bus_speed_8000;
default:
return ixgbe_bus_speed_unknown;
}
}
/**
* ixgbe_get_bus_info_generic - Generic set PCI bus info
* @hw: pointer to hardware structure
*
* Sets the PCI bus info (speed, width, type) within the ixgbe_hw structure
**/
int ixgbe_get_bus_info_generic(struct ixgbe_hw *hw)
{
u16 link_status;
hw->bus.type = ixgbe_bus_type_pci_express;
/* Get the negotiated link width and speed from PCI config space */
link_status = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_LINK_STATUS);
hw->bus.width = ixgbe_convert_bus_width(link_status);
hw->bus.speed = ixgbe_convert_bus_speed(link_status);
hw->mac.ops.set_lan_id(hw);
return 0;
}
/**
* ixgbe_set_lan_id_multi_port_pcie - Set LAN id for PCIe multiple port devices
* @hw: pointer to the HW structure
*
* Determines the LAN function id by reading memory-mapped registers
* and swaps the port value if requested.
**/
void ixgbe_set_lan_id_multi_port_pcie(struct ixgbe_hw *hw)
{
struct ixgbe_bus_info *bus = &hw->bus;
u16 ee_ctrl_4;
u32 reg;
reg = IXGBE_READ_REG(hw, IXGBE_STATUS);
bus->func = FIELD_GET(IXGBE_STATUS_LAN_ID, reg);
bus->lan_id = bus->func;
/* check for a port swap */
reg = IXGBE_READ_REG(hw, IXGBE_FACTPS(hw));
if (reg & IXGBE_FACTPS_LFS)
bus->func ^= 0x1;
/* Get MAC instance from EEPROM for configuring CS4227 */
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP) {
hw->eeprom.ops.read(hw, IXGBE_EEPROM_CTRL_4, &ee_ctrl_4);
bus->instance_id = FIELD_GET(IXGBE_EE_CTRL_4_INST_ID,
ee_ctrl_4);
}
}
/**
* ixgbe_stop_adapter_generic - Generic stop Tx/Rx units
* @hw: pointer to hardware structure
*
* Sets the adapter_stopped flag within ixgbe_hw struct. Clears interrupts,
* disables transmit and receive units. The adapter_stopped flag is used by
* the shared code and drivers to determine if the adapter is in a stopped
* state and should not touch the hardware.
**/
int ixgbe_stop_adapter_generic(struct ixgbe_hw *hw)
{
u32 reg_val;
u16 i;
/*
* Set the adapter_stopped flag so other driver functions stop touching
* the hardware
*/
hw->adapter_stopped = true;
/* Disable the receive unit */
hw->mac.ops.disable_rx(hw);
/* Clear interrupt mask to stop interrupts from being generated */
IXGBE_WRITE_REG(hw, IXGBE_EIMC, IXGBE_IRQ_CLEAR_MASK);
/* Clear any pending interrupts, flush previous writes */
IXGBE_READ_REG(hw, IXGBE_EICR);
/* Disable the transmit unit. Each queue must be disabled. */
for (i = 0; i < hw->mac.max_tx_queues; i++)
IXGBE_WRITE_REG(hw, IXGBE_TXDCTL(i), IXGBE_TXDCTL_SWFLSH);
/* Disable the receive unit by stopping each queue */
for (i = 0; i < hw->mac.max_rx_queues; i++) {
reg_val = IXGBE_READ_REG(hw, IXGBE_RXDCTL(i));
reg_val &= ~IXGBE_RXDCTL_ENABLE;
reg_val |= IXGBE_RXDCTL_SWFLSH;
IXGBE_WRITE_REG(hw, IXGBE_RXDCTL(i), reg_val);
}
/* flush all queues disables */
IXGBE_WRITE_FLUSH(hw);
usleep_range(1000, 2000);
/*
* Prevent the PCI-E bus from hanging by disabling PCI-E primary
* access and verify no pending requests
*/
return ixgbe_disable_pcie_primary(hw);
}
/**
* ixgbe_init_led_link_act_generic - Store the LED index link/activity.
* @hw: pointer to hardware structure
*
* Store the index for the link active LED. This will be used to support
* blinking the LED.
**/
int ixgbe_init_led_link_act_generic(struct ixgbe_hw *hw)
{
struct ixgbe_mac_info *mac = &hw->mac;
u32 led_reg, led_mode;
u16 i;
led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
/* Get LED link active from the LEDCTL register */
for (i = 0; i < 4; i++) {
led_mode = led_reg >> IXGBE_LED_MODE_SHIFT(i);
if ((led_mode & IXGBE_LED_MODE_MASK_BASE) ==
IXGBE_LED_LINK_ACTIVE) {
mac->led_link_act = i;
return 0;
}
}
/* If LEDCTL register does not have the LED link active set, then use
* known MAC defaults.
*/
switch (hw->mac.type) {
case ixgbe_mac_x550em_a:
mac->led_link_act = 0;
break;
case ixgbe_mac_X550EM_x:
mac->led_link_act = 1;
break;
default:
mac->led_link_act = 2;
}
return 0;
}
/**
* ixgbe_led_on_generic - Turns on the software controllable LEDs.
* @hw: pointer to hardware structure
* @index: led number to turn on
**/
int ixgbe_led_on_generic(struct ixgbe_hw *hw, u32 index)
{
u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
if (index > 3)
return -EINVAL;
/* To turn on the LED, set mode to ON. */
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg |= IXGBE_LED_ON << IXGBE_LED_MODE_SHIFT(index);
IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_led_off_generic - Turns off the software controllable LEDs.
* @hw: pointer to hardware structure
* @index: led number to turn off
**/
int ixgbe_led_off_generic(struct ixgbe_hw *hw, u32 index)
{
u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
if (index > 3)
return -EINVAL;
/* To turn off the LED, set mode to OFF. */
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg |= IXGBE_LED_OFF << IXGBE_LED_MODE_SHIFT(index);
IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_init_eeprom_params_generic - Initialize EEPROM params
* @hw: pointer to hardware structure
*
* Initializes the EEPROM parameters ixgbe_eeprom_info within the
* ixgbe_hw struct in order to set up EEPROM access.
**/
int ixgbe_init_eeprom_params_generic(struct ixgbe_hw *hw)
{
struct ixgbe_eeprom_info *eeprom = &hw->eeprom;
u32 eec;
u16 eeprom_size;
if (eeprom->type == ixgbe_eeprom_uninitialized) {
eeprom->type = ixgbe_eeprom_none;
/* Set default semaphore delay to 10ms which is a well
* tested value */
eeprom->semaphore_delay = 10;
/* Clear EEPROM page size, it will be initialized as needed */
eeprom->word_page_size = 0;
/*
* Check for EEPROM present first.
* If not present leave as none
*/
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
if (eec & IXGBE_EEC_PRES) {
eeprom->type = ixgbe_eeprom_spi;
/*
* SPI EEPROM is assumed here. This code would need to
* change if a future EEPROM is not SPI.
*/
eeprom_size = FIELD_GET(IXGBE_EEC_SIZE, eec);
eeprom->word_size = BIT(eeprom_size +
IXGBE_EEPROM_WORD_SIZE_SHIFT);
}
if (eec & IXGBE_EEC_ADDR_SIZE)
eeprom->address_bits = 16;
else
eeprom->address_bits = 8;
hw_dbg(hw, "Eeprom params: type = %d, size = %d, address bits: %d\n",
eeprom->type, eeprom->word_size, eeprom->address_bits);
}
return 0;
}
/**
* ixgbe_write_eeprom_buffer_bit_bang_generic - Write EEPROM using bit-bang
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to write
* @words: number of words
* @data: 16 bit word(s) to write to EEPROM
*
* Reads 16 bit word(s) from EEPROM through bit-bang method
**/
int ixgbe_write_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
u16 i, count;
int status;
hw->eeprom.ops.init_params(hw);
if (words == 0 || (offset + words > hw->eeprom.word_size))
return -EINVAL;
/*
* The EEPROM page size cannot be queried from the chip. We do lazy
* initialization. It is worth to do that when we write large buffer.
*/
if ((hw->eeprom.word_page_size == 0) &&
(words > IXGBE_EEPROM_PAGE_SIZE_MAX))
ixgbe_detect_eeprom_page_size_generic(hw, offset);
/*
* We cannot hold synchronization semaphores for too long
* to avoid other entity starvation. However it is more efficient
* to read in bursts than synchronizing access for each word.
*/
for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset + i,
count, &data[i]);
if (status != 0)
break;
}
return status;
}
/**
* ixgbe_write_eeprom_buffer_bit_bang - Writes 16 bit word(s) to EEPROM
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be written to
* @words: number of word(s)
* @data: 16 bit word(s) to be written to the EEPROM
*
* If ixgbe_eeprom_update_checksum is not called after this function, the
* EEPROM will most likely contain an invalid checksum.
**/
static int ixgbe_write_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
u8 write_opcode = IXGBE_EEPROM_WRITE_OPCODE_SPI;
u16 page_size;
int status;
u16 word;
u16 i;
/* Prepare the EEPROM for writing */
status = ixgbe_acquire_eeprom(hw);
if (status)
return status;
if (ixgbe_ready_eeprom(hw) != 0) {
ixgbe_release_eeprom(hw);
return -EIO;
}
for (i = 0; i < words; i++) {
ixgbe_standby_eeprom(hw);
/* Send the WRITE ENABLE command (8 bit opcode) */
ixgbe_shift_out_eeprom_bits(hw,
IXGBE_EEPROM_WREN_OPCODE_SPI,
IXGBE_EEPROM_OPCODE_BITS);
ixgbe_standby_eeprom(hw);
/* Some SPI eeproms use the 8th address bit embedded
* in the opcode
*/
if ((hw->eeprom.address_bits == 8) &&
((offset + i) >= 128))
write_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
/* Send the Write command (8-bit opcode + addr) */
ixgbe_shift_out_eeprom_bits(hw, write_opcode,
IXGBE_EEPROM_OPCODE_BITS);
ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
hw->eeprom.address_bits);
page_size = hw->eeprom.word_page_size;
/* Send the data in burst via SPI */
do {
word = data[i];
word = (word >> 8) | (word << 8);
ixgbe_shift_out_eeprom_bits(hw, word, 16);
if (page_size == 0)
break;
/* do not wrap around page */
if (((offset + i) & (page_size - 1)) ==
(page_size - 1))
break;
} while (++i < words);
ixgbe_standby_eeprom(hw);
usleep_range(10000, 20000);
}
/* Done with writing - release the EEPROM */
ixgbe_release_eeprom(hw);
return 0;
}
/**
* ixgbe_write_eeprom_generic - Writes 16 bit value to EEPROM
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be written to
* @data: 16 bit word to be written to the EEPROM
*
* If ixgbe_eeprom_update_checksum is not called after this function, the
* EEPROM will most likely contain an invalid checksum.
**/
int ixgbe_write_eeprom_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
{
hw->eeprom.ops.init_params(hw);
if (offset >= hw->eeprom.word_size)
return -EINVAL;
return ixgbe_write_eeprom_buffer_bit_bang(hw, offset, 1, &data);
}
/**
* ixgbe_read_eeprom_buffer_bit_bang_generic - Read EEPROM using bit-bang
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be read
* @words: number of word(s)
* @data: read 16 bit words(s) from EEPROM
*
* Reads 16 bit word(s) from EEPROM through bit-bang method
**/
int ixgbe_read_eeprom_buffer_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
u16 i, count;
int status;
hw->eeprom.ops.init_params(hw);
if (words == 0 || (offset + words > hw->eeprom.word_size))
return -EINVAL;
/*
* We cannot hold synchronization semaphores for too long
* to avoid other entity starvation. However it is more efficient
* to read in bursts than synchronizing access for each word.
*/
for (i = 0; i < words; i += IXGBE_EEPROM_RD_BUFFER_MAX_COUNT) {
count = (words - i) / IXGBE_EEPROM_RD_BUFFER_MAX_COUNT > 0 ?
IXGBE_EEPROM_RD_BUFFER_MAX_COUNT : (words - i);
status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset + i,
count, &data[i]);
if (status)
return status;
}
return 0;
}
/**
* ixgbe_read_eeprom_buffer_bit_bang - Read EEPROM using bit-bang
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be read
* @words: number of word(s)
* @data: read 16 bit word(s) from EEPROM
*
* Reads 16 bit word(s) from EEPROM through bit-bang method
**/
static int ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
u8 read_opcode = IXGBE_EEPROM_READ_OPCODE_SPI;
u16 word_in;
int status;
u16 i;
/* Prepare the EEPROM for reading */
status = ixgbe_acquire_eeprom(hw);
if (status)
return status;
if (ixgbe_ready_eeprom(hw) != 0) {
ixgbe_release_eeprom(hw);
return -EIO;
}
for (i = 0; i < words; i++) {
ixgbe_standby_eeprom(hw);
/* Some SPI eeproms use the 8th address bit embedded
* in the opcode
*/
if ((hw->eeprom.address_bits == 8) &&
((offset + i) >= 128))
read_opcode |= IXGBE_EEPROM_A8_OPCODE_SPI;
/* Send the READ command (opcode + addr) */
ixgbe_shift_out_eeprom_bits(hw, read_opcode,
IXGBE_EEPROM_OPCODE_BITS);
ixgbe_shift_out_eeprom_bits(hw, (u16)((offset + i) * 2),
hw->eeprom.address_bits);
/* Read the data. */
word_in = ixgbe_shift_in_eeprom_bits(hw, 16);
data[i] = (word_in >> 8) | (word_in << 8);
}
/* End this read operation */
ixgbe_release_eeprom(hw);
return 0;
}
/**
* ixgbe_read_eeprom_bit_bang_generic - Read EEPROM word using bit-bang
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be read
* @data: read 16 bit value from EEPROM
*
* Reads 16 bit value from EEPROM through bit-bang method
**/
int ixgbe_read_eeprom_bit_bang_generic(struct ixgbe_hw *hw, u16 offset,
u16 *data)
{
hw->eeprom.ops.init_params(hw);
if (offset >= hw->eeprom.word_size)
return -EINVAL;
return ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
}
/**
* ixgbe_read_eerd_buffer_generic - Read EEPROM word(s) using EERD
* @hw: pointer to hardware structure
* @offset: offset of word in the EEPROM to read
* @words: number of word(s)
* @data: 16 bit word(s) from the EEPROM
*
* Reads a 16 bit word(s) from the EEPROM using the EERD register.
**/
int ixgbe_read_eerd_buffer_generic(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
int status;
u32 eerd;
u32 i;
hw->eeprom.ops.init_params(hw);
if (words == 0 || offset >= hw->eeprom.word_size)
return -EINVAL;
for (i = 0; i < words; i++) {
eerd = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
IXGBE_EEPROM_RW_REG_START;
IXGBE_WRITE_REG(hw, IXGBE_EERD, eerd);
status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_READ);
if (status == 0) {
data[i] = (IXGBE_READ_REG(hw, IXGBE_EERD) >>
IXGBE_EEPROM_RW_REG_DATA);
} else {
hw_dbg(hw, "Eeprom read timed out\n");
return status;
}
}
return 0;
}
/**
* ixgbe_detect_eeprom_page_size_generic - Detect EEPROM page size
* @hw: pointer to hardware structure
* @offset: offset within the EEPROM to be used as a scratch pad
*
* Discover EEPROM page size by writing marching data at given offset.
* This function is called only when we are writing a new large buffer
* at given offset so the data would be overwritten anyway.
**/
static int ixgbe_detect_eeprom_page_size_generic(struct ixgbe_hw *hw,
u16 offset)
{
u16 data[IXGBE_EEPROM_PAGE_SIZE_MAX];
int status;
u16 i;
for (i = 0; i < IXGBE_EEPROM_PAGE_SIZE_MAX; i++)
data[i] = i;
hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX;
status = ixgbe_write_eeprom_buffer_bit_bang(hw, offset,
IXGBE_EEPROM_PAGE_SIZE_MAX, data);
hw->eeprom.word_page_size = 0;
if (status)
return status;
status = ixgbe_read_eeprom_buffer_bit_bang(hw, offset, 1, data);
if (status)
return status;
/*
* When writing in burst more than the actual page size
* EEPROM address wraps around current page.
*/
hw->eeprom.word_page_size = IXGBE_EEPROM_PAGE_SIZE_MAX - data[0];
hw_dbg(hw, "Detected EEPROM page size = %d words.\n",
hw->eeprom.word_page_size);
return 0;
}
/**
* ixgbe_read_eerd_generic - Read EEPROM word using EERD
* @hw: pointer to hardware structure
* @offset: offset of word in the EEPROM to read
* @data: word read from the EEPROM
*
* Reads a 16 bit word from the EEPROM using the EERD register.
**/
int ixgbe_read_eerd_generic(struct ixgbe_hw *hw, u16 offset, u16 *data)
{
return ixgbe_read_eerd_buffer_generic(hw, offset, 1, data);
}
/**
* ixgbe_write_eewr_buffer_generic - Write EEPROM word(s) using EEWR
* @hw: pointer to hardware structure
* @offset: offset of word in the EEPROM to write
* @words: number of words
* @data: word(s) write to the EEPROM
*
* Write a 16 bit word(s) to the EEPROM using the EEWR register.
**/
int ixgbe_write_eewr_buffer_generic(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data)
{
int status;
u32 eewr;
u16 i;
hw->eeprom.ops.init_params(hw);
if (words == 0 || offset >= hw->eeprom.word_size)
return -EINVAL;
for (i = 0; i < words; i++) {
eewr = ((offset + i) << IXGBE_EEPROM_RW_ADDR_SHIFT) |
(data[i] << IXGBE_EEPROM_RW_REG_DATA) |
IXGBE_EEPROM_RW_REG_START;
status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
if (status) {
hw_dbg(hw, "Eeprom write EEWR timed out\n");
return status;
}
IXGBE_WRITE_REG(hw, IXGBE_EEWR, eewr);
status = ixgbe_poll_eerd_eewr_done(hw, IXGBE_NVM_POLL_WRITE);
if (status) {
hw_dbg(hw, "Eeprom write EEWR timed out\n");
return status;
}
}
return 0;
}
/**
* ixgbe_write_eewr_generic - Write EEPROM word using EEWR
* @hw: pointer to hardware structure
* @offset: offset of word in the EEPROM to write
* @data: word write to the EEPROM
*
* Write a 16 bit word to the EEPROM using the EEWR register.
**/
int ixgbe_write_eewr_generic(struct ixgbe_hw *hw, u16 offset, u16 data)
{
return ixgbe_write_eewr_buffer_generic(hw, offset, 1, &data);
}
/**
* ixgbe_poll_eerd_eewr_done - Poll EERD read or EEWR write status
* @hw: pointer to hardware structure
* @ee_reg: EEPROM flag for polling
*
* Polls the status bit (bit 1) of the EERD or EEWR to determine when the
* read or write is done respectively.
**/
static int ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg)
{
u32 i;
u32 reg;
for (i = 0; i < IXGBE_EERD_EEWR_ATTEMPTS; i++) {
if (ee_reg == IXGBE_NVM_POLL_READ)
reg = IXGBE_READ_REG(hw, IXGBE_EERD);
else
reg = IXGBE_READ_REG(hw, IXGBE_EEWR);
if (reg & IXGBE_EEPROM_RW_REG_DONE) {
return 0;
}
udelay(5);
}
return -EIO;
}
/**
* ixgbe_acquire_eeprom - Acquire EEPROM using bit-bang
* @hw: pointer to hardware structure
*
* Prepares EEPROM for access using bit-bang method. This function should
* be called before issuing a command to the EEPROM.
**/
static int ixgbe_acquire_eeprom(struct ixgbe_hw *hw)
{
u32 eec;
u32 i;
if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) != 0)
return -EBUSY;
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/* Request EEPROM Access */
eec |= IXGBE_EEC_REQ;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
for (i = 0; i < IXGBE_EEPROM_GRANT_ATTEMPTS; i++) {
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
if (eec & IXGBE_EEC_GNT)
break;
udelay(5);
}
/* Release if grant not acquired */
if (!(eec & IXGBE_EEC_GNT)) {
eec &= ~IXGBE_EEC_REQ;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
hw_dbg(hw, "Could not acquire EEPROM grant\n");
hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
return -EIO;
}
/* Setup EEPROM for Read/Write */
/* Clear CS and SK */
eec &= ~(IXGBE_EEC_CS | IXGBE_EEC_SK);
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
return 0;
}
/**
* ixgbe_get_eeprom_semaphore - Get hardware semaphore
* @hw: pointer to hardware structure
*
* Sets the hardware semaphores so EEPROM access can occur for bit-bang method
**/
static int ixgbe_get_eeprom_semaphore(struct ixgbe_hw *hw)
{
u32 timeout = 2000;
u32 i;
u32 swsm;
/* Get SMBI software semaphore between device drivers first */
for (i = 0; i < timeout; i++) {
/*
* If the SMBI bit is 0 when we read it, then the bit will be
* set and we have the semaphore
*/
swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (!(swsm & IXGBE_SWSM_SMBI))
break;
usleep_range(50, 100);
}
if (i == timeout) {
hw_dbg(hw, "Driver can't access the Eeprom - SMBI Semaphore not granted.\n");
/* this release is particularly important because our attempts
* above to get the semaphore may have succeeded, and if there
* was a timeout, we should unconditionally clear the semaphore
* bits to free the driver to make progress
*/
ixgbe_release_eeprom_semaphore(hw);
usleep_range(50, 100);
/* one last try
* If the SMBI bit is 0 when we read it, then the bit will be
* set and we have the semaphore
*/
swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (swsm & IXGBE_SWSM_SMBI) {
hw_dbg(hw, "Software semaphore SMBI between device drivers not granted.\n");
return -EIO;
}
}
/* Now get the semaphore between SW/FW through the SWESMBI bit */
for (i = 0; i < timeout; i++) {
swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
/* Set the SW EEPROM semaphore bit to request access */
swsm |= IXGBE_SWSM_SWESMBI;
IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
/* If we set the bit successfully then we got the
* semaphore.
*/
swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
if (swsm & IXGBE_SWSM_SWESMBI)
break;
usleep_range(50, 100);
}
/* Release semaphores and return error if SW EEPROM semaphore
* was not granted because we don't have access to the EEPROM
*/
if (i >= timeout) {
hw_dbg(hw, "SWESMBI Software EEPROM semaphore not granted.\n");
ixgbe_release_eeprom_semaphore(hw);
return -EIO;
}
return 0;
}
/**
* ixgbe_release_eeprom_semaphore - Release hardware semaphore
* @hw: pointer to hardware structure
*
* This function clears hardware semaphore bits.
**/
static void ixgbe_release_eeprom_semaphore(struct ixgbe_hw *hw)
{
u32 swsm;
swsm = IXGBE_READ_REG(hw, IXGBE_SWSM(hw));
/* Release both semaphores by writing 0 to the bits SWESMBI and SMBI */
swsm &= ~(IXGBE_SWSM_SWESMBI | IXGBE_SWSM_SMBI);
IXGBE_WRITE_REG(hw, IXGBE_SWSM(hw), swsm);
IXGBE_WRITE_FLUSH(hw);
}
/**
* ixgbe_ready_eeprom - Polls for EEPROM ready
* @hw: pointer to hardware structure
**/
static int ixgbe_ready_eeprom(struct ixgbe_hw *hw)
{
u16 i;
u8 spi_stat_reg;
/*
* Read "Status Register" repeatedly until the LSB is cleared. The
* EEPROM will signal that the command has been completed by clearing
* bit 0 of the internal status register. If it's not cleared within
* 5 milliseconds, then error out.
*/
for (i = 0; i < IXGBE_EEPROM_MAX_RETRY_SPI; i += 5) {
ixgbe_shift_out_eeprom_bits(hw, IXGBE_EEPROM_RDSR_OPCODE_SPI,
IXGBE_EEPROM_OPCODE_BITS);
spi_stat_reg = (u8)ixgbe_shift_in_eeprom_bits(hw, 8);
if (!(spi_stat_reg & IXGBE_EEPROM_STATUS_RDY_SPI))
break;
udelay(5);
ixgbe_standby_eeprom(hw);
}
/*
* On some parts, SPI write time could vary from 0-20mSec on 3.3V
* devices (and only 0-5mSec on 5V devices)
*/
if (i >= IXGBE_EEPROM_MAX_RETRY_SPI) {
hw_dbg(hw, "SPI EEPROM Status error\n");
return -EIO;
}
return 0;
}
/**
* ixgbe_standby_eeprom - Returns EEPROM to a "standby" state
* @hw: pointer to hardware structure
**/
static void ixgbe_standby_eeprom(struct ixgbe_hw *hw)
{
u32 eec;
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/* Toggle CS to flush commands */
eec |= IXGBE_EEC_CS;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
eec &= ~IXGBE_EEC_CS;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
/**
* ixgbe_shift_out_eeprom_bits - Shift data bits out to the EEPROM.
* @hw: pointer to hardware structure
* @data: data to send to the EEPROM
* @count: number of bits to shift out
**/
static void ixgbe_shift_out_eeprom_bits(struct ixgbe_hw *hw, u16 data,
u16 count)
{
u32 eec;
u32 mask;
u32 i;
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
/*
* Mask is used to shift "count" bits of "data" out to the EEPROM
* one bit at a time. Determine the starting bit based on count
*/
mask = BIT(count - 1);
for (i = 0; i < count; i++) {
/*
* A "1" is shifted out to the EEPROM by setting bit "DI" to a
* "1", and then raising and then lowering the clock (the SK
* bit controls the clock input to the EEPROM). A "0" is
* shifted out to the EEPROM by setting "DI" to "0" and then
* raising and then lowering the clock.
*/
if (data & mask)
eec |= IXGBE_EEC_DI;
else
eec &= ~IXGBE_EEC_DI;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
ixgbe_raise_eeprom_clk(hw, &eec);
ixgbe_lower_eeprom_clk(hw, &eec);
/*
* Shift mask to signify next bit of data to shift in to the
* EEPROM
*/
mask = mask >> 1;
}
/* We leave the "DI" bit set to "0" when we leave this routine. */
eec &= ~IXGBE_EEC_DI;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
}
/**
* ixgbe_shift_in_eeprom_bits - Shift data bits in from the EEPROM
* @hw: pointer to hardware structure
* @count: number of bits to shift
**/
static u16 ixgbe_shift_in_eeprom_bits(struct ixgbe_hw *hw, u16 count)
{
u32 eec;
u32 i;
u16 data = 0;
/*
* In order to read a register from the EEPROM, we need to shift
* 'count' bits in from the EEPROM. Bits are "shifted in" by raising
* the clock input to the EEPROM (setting the SK bit), and then reading
* the value of the "DO" bit. During this "shifting in" process the
* "DI" bit should always be clear.
*/
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec &= ~(IXGBE_EEC_DO | IXGBE_EEC_DI);
for (i = 0; i < count; i++) {
data = data << 1;
ixgbe_raise_eeprom_clk(hw, &eec);
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec &= ~(IXGBE_EEC_DI);
if (eec & IXGBE_EEC_DO)
data |= 1;
ixgbe_lower_eeprom_clk(hw, &eec);
}
return data;
}
/**
* ixgbe_raise_eeprom_clk - Raises the EEPROM's clock input.
* @hw: pointer to hardware structure
* @eec: EEC register's current value
**/
static void ixgbe_raise_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
/*
* Raise the clock input to the EEPROM
* (setting the SK bit), then delay
*/
*eec = *eec | IXGBE_EEC_SK;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
/**
* ixgbe_lower_eeprom_clk - Lowers the EEPROM's clock input.
* @hw: pointer to hardware structure
* @eec: EEC's current value
**/
static void ixgbe_lower_eeprom_clk(struct ixgbe_hw *hw, u32 *eec)
{
/*
* Lower the clock input to the EEPROM (clearing the SK bit), then
* delay
*/
*eec = *eec & ~IXGBE_EEC_SK;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), *eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
}
/**
* ixgbe_release_eeprom - Release EEPROM, release semaphores
* @hw: pointer to hardware structure
**/
static void ixgbe_release_eeprom(struct ixgbe_hw *hw)
{
u32 eec;
eec = IXGBE_READ_REG(hw, IXGBE_EEC(hw));
eec |= IXGBE_EEC_CS; /* Pull CS high */
eec &= ~IXGBE_EEC_SK; /* Lower SCK */
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
IXGBE_WRITE_FLUSH(hw);
udelay(1);
/* Stop requesting EEPROM access */
eec &= ~IXGBE_EEC_REQ;
IXGBE_WRITE_REG(hw, IXGBE_EEC(hw), eec);
hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
/*
* Delay before attempt to obtain semaphore again to allow FW
* access. semaphore_delay is in ms we need us for usleep_range
*/
usleep_range(hw->eeprom.semaphore_delay * 1000,
hw->eeprom.semaphore_delay * 2000);
}
/**
* ixgbe_calc_eeprom_checksum_generic - Calculates and returns the checksum
* @hw: pointer to hardware structure
**/
int ixgbe_calc_eeprom_checksum_generic(struct ixgbe_hw *hw)
{
u16 i;
u16 j;
u16 checksum = 0;
u16 length = 0;
u16 pointer = 0;
u16 word = 0;
/* Include 0x0-0x3F in the checksum */
for (i = 0; i < IXGBE_EEPROM_CHECKSUM; i++) {
if (hw->eeprom.ops.read(hw, i, &word)) {
hw_dbg(hw, "EEPROM read failed\n");
break;
}
checksum += word;
}
/* Include all data from pointers except for the fw pointer */
for (i = IXGBE_PCIE_ANALOG_PTR; i < IXGBE_FW_PTR; i++) {
if (hw->eeprom.ops.read(hw, i, &pointer)) {
hw_dbg(hw, "EEPROM read failed\n");
return -EIO;
}
/* If the pointer seems invalid */
if (pointer == 0xFFFF || pointer == 0)
continue;
if (hw->eeprom.ops.read(hw, pointer, &length)) {
hw_dbg(hw, "EEPROM read failed\n");
return -EIO;
}
if (length == 0xFFFF || length == 0)
continue;
for (j = pointer + 1; j <= pointer + length; j++) {
if (hw->eeprom.ops.read(hw, j, &word)) {
hw_dbg(hw, "EEPROM read failed\n");
return -EIO;
}
checksum += word;
}
}
checksum = (u16)IXGBE_EEPROM_SUM - checksum;
return (int)checksum;
}
/**
* ixgbe_validate_eeprom_checksum_generic - Validate EEPROM checksum
* @hw: pointer to hardware structure
* @checksum_val: calculated checksum
*
* Performs checksum calculation and validates the EEPROM checksum. If the
* caller does not need checksum_val, the value can be NULL.
**/
int ixgbe_validate_eeprom_checksum_generic(struct ixgbe_hw *hw,
u16 *checksum_val)
{
u16 read_checksum = 0;
u16 checksum;
int status;
/*
* Read the first word from the EEPROM. If this times out or fails, do
* not continue or we could be in for a very long wait while every
* EEPROM read fails
*/
status = hw->eeprom.ops.read(hw, 0, &checksum);
if (status) {
hw_dbg(hw, "EEPROM read failed\n");
return status;
}
status = hw->eeprom.ops.calc_checksum(hw);
if (status < 0)
return status;
checksum = (u16)(status & 0xffff);
status = hw->eeprom.ops.read(hw, IXGBE_EEPROM_CHECKSUM, &read_checksum);
if (status) {
hw_dbg(hw, "EEPROM read failed\n");
return status;
}
/* Verify read checksum from EEPROM is the same as
* calculated checksum
*/
if (read_checksum != checksum)
status = -EIO;
/* If the user cares, return the calculated checksum */
if (checksum_val)
*checksum_val = checksum;
return status;
}
/**
* ixgbe_update_eeprom_checksum_generic - Updates the EEPROM checksum
* @hw: pointer to hardware structure
**/
int ixgbe_update_eeprom_checksum_generic(struct ixgbe_hw *hw)
{
u16 checksum;
int status;
/*
* Read the first word from the EEPROM. If this times out or fails, do
* not continue or we could be in for a very long wait while every
* EEPROM read fails
*/
status = hw->eeprom.ops.read(hw, 0, &checksum);
if (status) {
hw_dbg(hw, "EEPROM read failed\n");
return status;
}
status = hw->eeprom.ops.calc_checksum(hw);
if (status < 0)
return status;
checksum = (u16)(status & 0xffff);
status = hw->eeprom.ops.write(hw, IXGBE_EEPROM_CHECKSUM, checksum);
return status;
}
/**
* ixgbe_set_rar_generic - Set Rx address register
* @hw: pointer to hardware structure
* @index: Receive address register to write
* @addr: Address to put into receive address register
* @vmdq: VMDq "set" or "pool" index
* @enable_addr: set flag that address is active
*
* Puts an ethernet address into a receive address register.
**/
int ixgbe_set_rar_generic(struct ixgbe_hw *hw, u32 index, u8 *addr, u32 vmdq,
u32 enable_addr)
{
u32 rar_low, rar_high;
u32 rar_entries = hw->mac.num_rar_entries;
/* Make sure we are using a valid rar index range */
if (index >= rar_entries) {
hw_dbg(hw, "RAR index %d is out of range.\n", index);
return -EINVAL;
}
/* setup VMDq pool selection before this RAR gets enabled */
hw->mac.ops.set_vmdq(hw, index, vmdq);
/*
* HW expects these in little endian so we reverse the byte
* order from network order (big endian) to little endian
*/
rar_low = ((u32)addr[0] |
((u32)addr[1] << 8) |
((u32)addr[2] << 16) |
((u32)addr[3] << 24));
/*
* Some parts put the VMDq setting in the extra RAH bits,
* so save everything except the lower 16 bits that hold part
* of the address and the address valid bit.
*/
rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
rar_high |= ((u32)addr[4] | ((u32)addr[5] << 8));
if (enable_addr != 0)
rar_high |= IXGBE_RAH_AV;
/* Record lower 32 bits of MAC address and then make
* sure that write is flushed to hardware before writing
* the upper 16 bits and setting the valid bit.
*/
IXGBE_WRITE_REG(hw, IXGBE_RAL(index), rar_low);
IXGBE_WRITE_FLUSH(hw);
IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
return 0;
}
/**
* ixgbe_clear_rar_generic - Remove Rx address register
* @hw: pointer to hardware structure
* @index: Receive address register to write
*
* Clears an ethernet address from a receive address register.
**/
int ixgbe_clear_rar_generic(struct ixgbe_hw *hw, u32 index)
{
u32 rar_high;
u32 rar_entries = hw->mac.num_rar_entries;
/* Make sure we are using a valid rar index range */
if (index >= rar_entries) {
hw_dbg(hw, "RAR index %d is out of range.\n", index);
return -EINVAL;
}
/*
* Some parts put the VMDq setting in the extra RAH bits,
* so save everything except the lower 16 bits that hold part
* of the address and the address valid bit.
*/
rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(index));
rar_high &= ~(0x0000FFFF | IXGBE_RAH_AV);
/* Clear the address valid bit and upper 16 bits of the address
* before clearing the lower bits. This way we aren't updating
* a live filter.
*/
IXGBE_WRITE_REG(hw, IXGBE_RAH(index), rar_high);
IXGBE_WRITE_FLUSH(hw);
IXGBE_WRITE_REG(hw, IXGBE_RAL(index), 0);
/* clear VMDq pool/queue selection for this RAR */
hw->mac.ops.clear_vmdq(hw, index, IXGBE_CLEAR_VMDQ_ALL);
return 0;
}
/**
* ixgbe_init_rx_addrs_generic - Initializes receive address filters.
* @hw: pointer to hardware structure
*
* Places the MAC address in receive address register 0 and clears the rest
* of the receive address registers. Clears the multicast table. Assumes
* the receiver is in reset when the routine is called.
**/
int ixgbe_init_rx_addrs_generic(struct ixgbe_hw *hw)
{
u32 i;
u32 rar_entries = hw->mac.num_rar_entries;
/*
* If the current mac address is valid, assume it is a software override
* to the permanent address.
* Otherwise, use the permanent address from the eeprom.
*/
if (!is_valid_ether_addr(hw->mac.addr)) {
/* Get the MAC address from the RAR0 for later reference */
hw->mac.ops.get_mac_addr(hw, hw->mac.addr);
hw_dbg(hw, " Keeping Current RAR0 Addr =%pM\n", hw->mac.addr);
} else {
/* Setup the receive address. */
hw_dbg(hw, "Overriding MAC Address in RAR[0]\n");
hw_dbg(hw, " New MAC Addr =%pM\n", hw->mac.addr);
hw->mac.ops.set_rar(hw, 0, hw->mac.addr, 0, IXGBE_RAH_AV);
}
/* clear VMDq pool/queue selection for RAR 0 */
hw->mac.ops.clear_vmdq(hw, 0, IXGBE_CLEAR_VMDQ_ALL);
hw->addr_ctrl.overflow_promisc = 0;
hw->addr_ctrl.rar_used_count = 1;
/* Zero out the other receive addresses. */
hw_dbg(hw, "Clearing RAR[1-%d]\n", rar_entries - 1);
for (i = 1; i < rar_entries; i++) {
IXGBE_WRITE_REG(hw, IXGBE_RAL(i), 0);
IXGBE_WRITE_REG(hw, IXGBE_RAH(i), 0);
}
/* Clear the MTA */
hw->addr_ctrl.mta_in_use = 0;
IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
hw_dbg(hw, " Clearing MTA\n");
for (i = 0; i < hw->mac.mcft_size; i++)
IXGBE_WRITE_REG(hw, IXGBE_MTA(i), 0);
if (hw->mac.ops.init_uta_tables)
hw->mac.ops.init_uta_tables(hw);
return 0;
}
/**
* ixgbe_mta_vector - Determines bit-vector in multicast table to set
* @hw: pointer to hardware structure
* @mc_addr: the multicast address
*
* Extracts the 12 bits, from a multicast address, to determine which
* bit-vector to set in the multicast table. The hardware uses 12 bits, from
* incoming rx multicast addresses, to determine the bit-vector to check in
* the MTA. Which of the 4 combination, of 12-bits, the hardware uses is set
* by the MO field of the MCSTCTRL. The MO field is set during initialization
* to mc_filter_type.
**/
static int ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr)
{
u32 vector = 0;
switch (hw->mac.mc_filter_type) {
case 0: /* use bits [47:36] of the address */
vector = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
break;
case 1: /* use bits [46:35] of the address */
vector = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
break;
case 2: /* use bits [45:34] of the address */
vector = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
break;
case 3: /* use bits [43:32] of the address */
vector = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
break;
default: /* Invalid mc_filter_type */
hw_dbg(hw, "MC filter type param set incorrectly\n");
break;
}
/* vector can only be 12-bits or boundary will be exceeded */
vector &= 0xFFF;
return vector;
}
/**
* ixgbe_set_mta - Set bit-vector in multicast table
* @hw: pointer to hardware structure
* @mc_addr: Multicast address
*
* Sets the bit-vector in the multicast table.
**/
static void ixgbe_set_mta(struct ixgbe_hw *hw, u8 *mc_addr)
{
u32 vector;
u32 vector_bit;
u32 vector_reg;
hw->addr_ctrl.mta_in_use++;
vector = ixgbe_mta_vector(hw, mc_addr);
hw_dbg(hw, " bit-vector = 0x%03X\n", vector);
/*
* The MTA is a register array of 128 32-bit registers. It is treated
* like an array of 4096 bits. We want to set bit
* BitArray[vector_value]. So we figure out what register the bit is
* in, read it, OR in the new bit, then write back the new value. The
* register is determined by the upper 7 bits of the vector value and
* the bit within that register are determined by the lower 5 bits of
* the value.
*/
vector_reg = (vector >> 5) & 0x7F;
vector_bit = vector & 0x1F;
hw->mac.mta_shadow[vector_reg] |= BIT(vector_bit);
}
/**
* ixgbe_update_mc_addr_list_generic - Updates MAC list of multicast addresses
* @hw: pointer to hardware structure
* @netdev: pointer to net device structure
*
* The given list replaces any existing list. Clears the MC addrs from receive
* address registers and the multicast table. Uses unused receive address
* registers for the first multicast addresses, and hashes the rest into the
* multicast table.
**/
int ixgbe_update_mc_addr_list_generic(struct ixgbe_hw *hw,
struct net_device *netdev)
{
struct netdev_hw_addr *ha;
u32 i;
/*
* Set the new number of MC addresses that we are being requested to
* use.
*/
hw->addr_ctrl.num_mc_addrs = netdev_mc_count(netdev);
hw->addr_ctrl.mta_in_use = 0;
/* Clear mta_shadow */
hw_dbg(hw, " Clearing MTA\n");
memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
/* Update mta shadow */
netdev_for_each_mc_addr(ha, netdev) {
hw_dbg(hw, " Adding the multicast addresses:\n");
ixgbe_set_mta(hw, ha->addr);
}
/* Enable mta */
for (i = 0; i < hw->mac.mcft_size; i++)
IXGBE_WRITE_REG_ARRAY(hw, IXGBE_MTA(0), i,
hw->mac.mta_shadow[i]);
if (hw->addr_ctrl.mta_in_use > 0)
IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL,
IXGBE_MCSTCTRL_MFE | hw->mac.mc_filter_type);
hw_dbg(hw, "ixgbe_update_mc_addr_list_generic Complete\n");
return 0;
}
/**
* ixgbe_enable_mc_generic - Enable multicast address in RAR
* @hw: pointer to hardware structure
*
* Enables multicast address in RAR and the use of the multicast hash table.
**/
int ixgbe_enable_mc_generic(struct ixgbe_hw *hw)
{
struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
if (a->mta_in_use > 0)
IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, IXGBE_MCSTCTRL_MFE |
hw->mac.mc_filter_type);
return 0;
}
/**
* ixgbe_disable_mc_generic - Disable multicast address in RAR
* @hw: pointer to hardware structure
*
* Disables multicast address in RAR and the use of the multicast hash table.
**/
int ixgbe_disable_mc_generic(struct ixgbe_hw *hw)
{
struct ixgbe_addr_filter_info *a = &hw->addr_ctrl;
if (a->mta_in_use > 0)
IXGBE_WRITE_REG(hw, IXGBE_MCSTCTRL, hw->mac.mc_filter_type);
return 0;
}
/**
* ixgbe_fc_enable_generic - Enable flow control
* @hw: pointer to hardware structure
*
* Enable flow control according to the current settings.
**/
int ixgbe_fc_enable_generic(struct ixgbe_hw *hw)
{
u32 mflcn_reg, fccfg_reg;
u32 reg;
u32 fcrtl, fcrth;
int i;
/* Validate the water mark configuration. */
if (!hw->fc.pause_time)
return -EINVAL;
/* Low water mark of zero causes XOFF floods */
for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
hw->fc.high_water[i]) {
if (!hw->fc.low_water[i] ||
hw->fc.low_water[i] >= hw->fc.high_water[i]) {
hw_dbg(hw, "Invalid water mark configuration\n");
return -EINVAL;
}
}
}
/* Negotiate the fc mode to use */
hw->mac.ops.fc_autoneg(hw);
/* Disable any previous flow control settings */
mflcn_reg = IXGBE_READ_REG(hw, IXGBE_MFLCN);
mflcn_reg &= ~(IXGBE_MFLCN_RPFCE_MASK | IXGBE_MFLCN_RFCE);
fccfg_reg = IXGBE_READ_REG(hw, IXGBE_FCCFG);
fccfg_reg &= ~(IXGBE_FCCFG_TFCE_802_3X | IXGBE_FCCFG_TFCE_PRIORITY);
/*
* The possible values of fc.current_mode are:
* 0: Flow control is completely disabled
* 1: Rx flow control is enabled (we can receive pause frames,
* but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames but
* we do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
* other: Invalid.
*/
switch (hw->fc.current_mode) {
case ixgbe_fc_none:
/*
* Flow control is disabled by software override or autoneg.
* The code below will actually disable it in the HW.
*/
break;
case ixgbe_fc_rx_pause:
/*
* Rx Flow control is enabled and Tx Flow control is
* disabled by software override. Since there really
* isn't a way to advertise that we are capable of RX
* Pause ONLY, we will advertise that we support both
* symmetric and asymmetric Rx PAUSE. Later, we will
* disable the adapter's ability to send PAUSE frames.
*/
mflcn_reg |= IXGBE_MFLCN_RFCE;
break;
case ixgbe_fc_tx_pause:
/*
* Tx Flow control is enabled, and Rx Flow control is
* disabled by software override.
*/
fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
break;
case ixgbe_fc_full:
/* Flow control (both Rx and Tx) is enabled by SW override. */
mflcn_reg |= IXGBE_MFLCN_RFCE;
fccfg_reg |= IXGBE_FCCFG_TFCE_802_3X;
break;
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
return -EIO;
}
/* Set 802.3x based flow control settings. */
mflcn_reg |= IXGBE_MFLCN_DPF;
IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);
/* Set up and enable Rx high/low water mark thresholds, enable XON. */
for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
if ((hw->fc.current_mode & ixgbe_fc_tx_pause) &&
hw->fc.high_water[i]) {
fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE;
IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), fcrtl);
fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN;
} else {
IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), 0);
/*
* In order to prevent Tx hangs when the internal Tx
* switch is enabled we must set the high water mark
* to the Rx packet buffer size - 24KB. This allows
* the Tx switch to function even under heavy Rx
* workloads.
*/
fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i)) - 24576;
}
IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), fcrth);
}
/* Configure pause time (2 TCs per register) */
reg = hw->fc.pause_time * 0x00010001U;
for (i = 0; i < (MAX_TRAFFIC_CLASS / 2); i++)
IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg);
IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2);
return 0;
}
/**
* ixgbe_negotiate_fc - Negotiate flow control
* @hw: pointer to hardware structure
* @adv_reg: flow control advertised settings
* @lp_reg: link partner's flow control settings
* @adv_sym: symmetric pause bit in advertisement
* @adv_asm: asymmetric pause bit in advertisement
* @lp_sym: symmetric pause bit in link partner advertisement
* @lp_asm: asymmetric pause bit in link partner advertisement
*
* Find the intersection between advertised settings and link partner's
* advertised settings
**/
int ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
{
if ((!(adv_reg)) || (!(lp_reg)))
return -EINVAL;
if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
/*
* Now we need to check if the user selected Rx ONLY
* of pause frames. In this case, we had to advertise
* FULL flow control because we could not advertise RX
* ONLY. Hence, we must now check to see if we need to
* turn OFF the TRANSMISSION of PAUSE frames.
*/
if (hw->fc.requested_mode == ixgbe_fc_full) {
hw->fc.current_mode = ixgbe_fc_full;
hw_dbg(hw, "Flow Control = FULL.\n");
} else {
hw->fc.current_mode = ixgbe_fc_rx_pause;
hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
}
} else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
hw->fc.current_mode = ixgbe_fc_tx_pause;
hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
} else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
!(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
hw->fc.current_mode = ixgbe_fc_rx_pause;
hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
} else {
hw->fc.current_mode = ixgbe_fc_none;
hw_dbg(hw, "Flow Control = NONE.\n");
}
return 0;
}
/**
* ixgbe_fc_autoneg_fiber - Enable flow control on 1 gig fiber
* @hw: pointer to hardware structure
*
* Enable flow control according on 1 gig fiber.
**/
static int ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw)
{
u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
int ret_val;
/*
* On multispeed fiber at 1g, bail out if
* - link is up but AN did not complete, or if
* - link is up and AN completed but timed out
*/
linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
if ((!!(linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
(!!(linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1))
return -EIO;
pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
ret_val = ixgbe_negotiate_fc(hw, pcs_anadv_reg,
pcs_lpab_reg, IXGBE_PCS1GANA_SYM_PAUSE,
IXGBE_PCS1GANA_ASM_PAUSE,
IXGBE_PCS1GANA_SYM_PAUSE,
IXGBE_PCS1GANA_ASM_PAUSE);
return ret_val;
}
/**
* ixgbe_fc_autoneg_backplane - Enable flow control IEEE clause 37
* @hw: pointer to hardware structure
*
* Enable flow control according to IEEE clause 37.
**/
static int ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw)
{
u32 links2, anlp1_reg, autoc_reg, links;
int ret_val;
/*
* On backplane, bail out if
* - backplane autoneg was not completed, or if
* - we are 82599 and link partner is not AN enabled
*/
links = IXGBE_READ_REG(hw, IXGBE_LINKS);
if ((links & IXGBE_LINKS_KX_AN_COMP) == 0)
return -EIO;
if (hw->mac.type == ixgbe_mac_82599EB) {
links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
if ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)
return -EIO;
}
/*
* Read the 10g AN autoc and LP ability registers and resolve
* local flow control settings accordingly
*/
autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
ret_val = ixgbe_negotiate_fc(hw, autoc_reg,
anlp1_reg, IXGBE_AUTOC_SYM_PAUSE, IXGBE_AUTOC_ASM_PAUSE,
IXGBE_ANLP1_SYM_PAUSE, IXGBE_ANLP1_ASM_PAUSE);
return ret_val;
}
/**
* ixgbe_fc_autoneg_copper - Enable flow control IEEE clause 37
* @hw: pointer to hardware structure
*
* Enable flow control according to IEEE clause 37.
**/
static int ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw)
{
u16 technology_ability_reg = 0;
u16 lp_technology_ability_reg = 0;
hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
MDIO_MMD_AN,
&technology_ability_reg);
hw->phy.ops.read_reg(hw, MDIO_AN_LPA,
MDIO_MMD_AN,
&lp_technology_ability_reg);
return ixgbe_negotiate_fc(hw, (u32)technology_ability_reg,
(u32)lp_technology_ability_reg,
IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE,
IXGBE_TAF_SYM_PAUSE, IXGBE_TAF_ASM_PAUSE);
}
/**
* ixgbe_fc_autoneg - Configure flow control
* @hw: pointer to hardware structure
*
* Compares our advertised flow control capabilities to those advertised by
* our link partner, and determines the proper flow control mode to use.
**/
void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
{
ixgbe_link_speed speed;
int ret_val = -EIO;
bool link_up;
/*
* AN should have completed when the cable was plugged in.
* Look for reasons to bail out. Bail out if:
* - FC autoneg is disabled, or if
* - link is not up.
*
* Since we're being called from an LSC, link is already known to be up.
* So use link_up_wait_to_complete=false.
*/
if (hw->fc.disable_fc_autoneg)
goto out;
hw->mac.ops.check_link(hw, &speed, &link_up, false);
if (!link_up)
goto out;
switch (hw->phy.media_type) {
/* Autoneg flow control on fiber adapters */
case ixgbe_media_type_fiber:
if (speed == IXGBE_LINK_SPEED_1GB_FULL)
ret_val = ixgbe_fc_autoneg_fiber(hw);
break;
/* Autoneg flow control on backplane adapters */
case ixgbe_media_type_backplane:
ret_val = ixgbe_fc_autoneg_backplane(hw);
break;
/* Autoneg flow control on copper adapters */
case ixgbe_media_type_copper:
if (ixgbe_device_supports_autoneg_fc(hw))
ret_val = ixgbe_fc_autoneg_copper(hw);
break;
default:
break;
}
out:
if (ret_val == 0) {
hw->fc.fc_was_autonegged = true;
} else {
hw->fc.fc_was_autonegged = false;
hw->fc.current_mode = hw->fc.requested_mode;
}
}
/**
* ixgbe_pcie_timeout_poll - Return number of times to poll for completion
* @hw: pointer to hardware structure
*
* System-wide timeout range is encoded in PCIe Device Control2 register.
*
* Add 10% to specified maximum and return the number of times to poll for
* completion timeout, in units of 100 microsec. Never return less than
* 800 = 80 millisec.
**/
static u32 ixgbe_pcie_timeout_poll(struct ixgbe_hw *hw)
{
s16 devctl2;
u32 pollcnt;
devctl2 = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_CONTROL2);
devctl2 &= IXGBE_PCIDEVCTRL2_TIMEO_MASK;
switch (devctl2) {
case IXGBE_PCIDEVCTRL2_65_130ms:
pollcnt = 1300; /* 130 millisec */
break;
case IXGBE_PCIDEVCTRL2_260_520ms:
pollcnt = 5200; /* 520 millisec */
break;
case IXGBE_PCIDEVCTRL2_1_2s:
pollcnt = 20000; /* 2 sec */
break;
case IXGBE_PCIDEVCTRL2_4_8s:
pollcnt = 80000; /* 8 sec */
break;
case IXGBE_PCIDEVCTRL2_17_34s:
pollcnt = 34000; /* 34 sec */
break;
case IXGBE_PCIDEVCTRL2_50_100us: /* 100 microsecs */
case IXGBE_PCIDEVCTRL2_1_2ms: /* 2 millisecs */
case IXGBE_PCIDEVCTRL2_16_32ms: /* 32 millisec */
case IXGBE_PCIDEVCTRL2_16_32ms_def: /* 32 millisec default */
default:
pollcnt = 800; /* 80 millisec minimum */
break;
}
/* add 10% to spec maximum */
return (pollcnt * 11) / 10;
}
/**
* ixgbe_disable_pcie_primary - Disable PCI-express primary access
* @hw: pointer to hardware structure
*
* Disables PCI-Express primary access and verifies there are no pending
* requests. -EALREADY is returned if primary disable
* bit hasn't caused the primary requests to be disabled, else 0
* is returned signifying primary requests disabled.
**/
static int ixgbe_disable_pcie_primary(struct ixgbe_hw *hw)
{
u32 i, poll;
u16 value;
/* Always set this bit to ensure any future transactions are blocked */
IXGBE_WRITE_REG(hw, IXGBE_CTRL, IXGBE_CTRL_GIO_DIS);
/* Poll for bit to read as set */
for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
if (IXGBE_READ_REG(hw, IXGBE_CTRL) & IXGBE_CTRL_GIO_DIS)
break;
usleep_range(100, 120);
}
if (i >= IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT) {
hw_dbg(hw, "GIO disable did not set - requesting resets\n");
goto gio_disable_fail;
}
/* Exit if primary requests are blocked */
if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO) ||
ixgbe_removed(hw->hw_addr))
return 0;
/* Poll for primary request bit to clear */
for (i = 0; i < IXGBE_PCI_PRIMARY_DISABLE_TIMEOUT; i++) {
udelay(100);
if (!(IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_GIO))
return 0;
}
/*
* Two consecutive resets are required via CTRL.RST per datasheet
* 5.2.5.3.2 Primary Disable. We set a flag to inform the reset routine
* of this need. The first reset prevents new primary requests from
* being issued by our device. We then must wait 1usec or more for any
* remaining completions from the PCIe bus to trickle in, and then reset
* again to clear out any effects they may have had on our device.
*/
hw_dbg(hw, "GIO Primary Disable bit didn't clear - requesting resets\n");
gio_disable_fail:
hw->mac.flags |= IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
if (hw->mac.type >= ixgbe_mac_X550)
return 0;
/*
* Before proceeding, make sure that the PCIe block does not have
* transactions pending.
*/
poll = ixgbe_pcie_timeout_poll(hw);
for (i = 0; i < poll; i++) {
udelay(100);
value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
if (ixgbe_removed(hw->hw_addr))
return 0;
if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
return 0;
}
hw_dbg(hw, "PCIe transaction pending bit also did not clear.\n");
return -EALREADY;
}
/**
* ixgbe_acquire_swfw_sync - Acquire SWFW semaphore
* @hw: pointer to hardware structure
* @mask: Mask to specify which semaphore to acquire
*
* Acquires the SWFW semaphore through the GSSR register for the specified
* function (CSR, PHY0, PHY1, EEPROM, Flash)
**/
int ixgbe_acquire_swfw_sync(struct ixgbe_hw *hw, u32 mask)
{
u32 gssr = 0;
u32 swmask = mask;
u32 fwmask = mask << 5;
u32 timeout = 200;
u32 i;
for (i = 0; i < timeout; i++) {
/*
* SW NVM semaphore bit is used for access to all
* SW_FW_SYNC bits (not just NVM)
*/
if (ixgbe_get_eeprom_semaphore(hw))
return -EBUSY;
gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
if (!(gssr & (fwmask | swmask))) {
gssr |= swmask;
IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
ixgbe_release_eeprom_semaphore(hw);
return 0;
} else {
/* Resource is currently in use by FW or SW */
ixgbe_release_eeprom_semaphore(hw);
usleep_range(5000, 10000);
}
}
/* If time expired clear the bits holding the lock and retry */
if (gssr & (fwmask | swmask))
ixgbe_release_swfw_sync(hw, gssr & (fwmask | swmask));
usleep_range(5000, 10000);
return -EBUSY;
}
/**
* ixgbe_release_swfw_sync - Release SWFW semaphore
* @hw: pointer to hardware structure
* @mask: Mask to specify which semaphore to release
*
* Releases the SWFW semaphore through the GSSR register for the specified
* function (CSR, PHY0, PHY1, EEPROM, Flash)
**/
void ixgbe_release_swfw_sync(struct ixgbe_hw *hw, u32 mask)
{
u32 gssr;
u32 swmask = mask;
ixgbe_get_eeprom_semaphore(hw);
gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
gssr &= ~swmask;
IXGBE_WRITE_REG(hw, IXGBE_GSSR, gssr);
ixgbe_release_eeprom_semaphore(hw);
}
/**
* prot_autoc_read_generic - Hides MAC differences needed for AUTOC read
* @hw: pointer to hardware structure
* @reg_val: Value we read from AUTOC
* @locked: bool to indicate whether the SW/FW lock should be taken. Never
* true in this the generic case.
*
* The default case requires no protection so just to the register read.
**/
int prot_autoc_read_generic(struct ixgbe_hw *hw, bool *locked, u32 *reg_val)
{
*locked = false;
*reg_val = IXGBE_READ_REG(hw, IXGBE_AUTOC);
return 0;
}
/**
* prot_autoc_write_generic - Hides MAC differences needed for AUTOC write
* @hw: pointer to hardware structure
* @reg_val: value to write to AUTOC
* @locked: bool to indicate whether the SW/FW lock was already taken by
* previous read.
**/
int prot_autoc_write_generic(struct ixgbe_hw *hw, u32 reg_val, bool locked)
{
IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_val);
return 0;
}
/**
* ixgbe_disable_rx_buff_generic - Stops the receive data path
* @hw: pointer to hardware structure
*
* Stops the receive data path and waits for the HW to internally
* empty the Rx security block.
**/
int ixgbe_disable_rx_buff_generic(struct ixgbe_hw *hw)
{
#define IXGBE_MAX_SECRX_POLL 40
int i;
int secrxreg;
secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
secrxreg |= IXGBE_SECRXCTRL_RX_DIS;
IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
for (i = 0; i < IXGBE_MAX_SECRX_POLL; i++) {
secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXSTAT);
if (secrxreg & IXGBE_SECRXSTAT_SECRX_RDY)
break;
else
/* Use interrupt-safe sleep just in case */
udelay(1000);
}
/* For informational purposes only */
if (i >= IXGBE_MAX_SECRX_POLL)
hw_dbg(hw, "Rx unit being enabled before security path fully disabled. Continuing with init.\n");
return 0;
}
/**
* ixgbe_enable_rx_buff_generic - Enables the receive data path
* @hw: pointer to hardware structure
*
* Enables the receive data path
**/
int ixgbe_enable_rx_buff_generic(struct ixgbe_hw *hw)
{
u32 secrxreg;
secrxreg = IXGBE_READ_REG(hw, IXGBE_SECRXCTRL);
secrxreg &= ~IXGBE_SECRXCTRL_RX_DIS;
IXGBE_WRITE_REG(hw, IXGBE_SECRXCTRL, secrxreg);
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_enable_rx_dma_generic - Enable the Rx DMA unit
* @hw: pointer to hardware structure
* @regval: register value to write to RXCTRL
*
* Enables the Rx DMA unit
**/
int ixgbe_enable_rx_dma_generic(struct ixgbe_hw *hw, u32 regval)
{
if (regval & IXGBE_RXCTRL_RXEN)
hw->mac.ops.enable_rx(hw);
else
hw->mac.ops.disable_rx(hw);
return 0;
}
/**
* ixgbe_blink_led_start_generic - Blink LED based on index.
* @hw: pointer to hardware structure
* @index: led number to blink
**/
int ixgbe_blink_led_start_generic(struct ixgbe_hw *hw, u32 index)
{
u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
ixgbe_link_speed speed = 0;
bool link_up = false;
bool locked = false;
int ret_val;
if (index > 3)
return -EINVAL;
/*
* Link must be up to auto-blink the LEDs;
* Force it if link is down.
*/
hw->mac.ops.check_link(hw, &speed, &link_up, false);
if (!link_up) {
ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
if (ret_val)
return ret_val;
autoc_reg |= IXGBE_AUTOC_AN_RESTART;
autoc_reg |= IXGBE_AUTOC_FLU;
ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
if (ret_val)
return ret_val;
IXGBE_WRITE_FLUSH(hw);
usleep_range(10000, 20000);
}
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg |= IXGBE_LED_BLINK(index);
IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_blink_led_stop_generic - Stop blinking LED based on index.
* @hw: pointer to hardware structure
* @index: led number to stop blinking
**/
int ixgbe_blink_led_stop_generic(struct ixgbe_hw *hw, u32 index)
{
u32 led_reg = IXGBE_READ_REG(hw, IXGBE_LEDCTL);
bool locked = false;
u32 autoc_reg = 0;
int ret_val;
if (index > 3)
return -EINVAL;
ret_val = hw->mac.ops.prot_autoc_read(hw, &locked, &autoc_reg);
if (ret_val)
return ret_val;
autoc_reg &= ~IXGBE_AUTOC_FLU;
autoc_reg |= IXGBE_AUTOC_AN_RESTART;
ret_val = hw->mac.ops.prot_autoc_write(hw, autoc_reg, locked);
if (ret_val)
return ret_val;
led_reg &= ~IXGBE_LED_MODE_MASK(index);
led_reg &= ~IXGBE_LED_BLINK(index);
led_reg |= IXGBE_LED_LINK_ACTIVE << IXGBE_LED_MODE_SHIFT(index);
IXGBE_WRITE_REG(hw, IXGBE_LEDCTL, led_reg);
IXGBE_WRITE_FLUSH(hw);
return 0;
}
/**
* ixgbe_get_san_mac_addr_offset - Get SAN MAC address offset from the EEPROM
* @hw: pointer to hardware structure
* @san_mac_offset: SAN MAC address offset
*
* This function will read the EEPROM location for the SAN MAC address
* pointer, and returns the value at that location. This is used in both
* get and set mac_addr routines.
**/
static int ixgbe_get_san_mac_addr_offset(struct ixgbe_hw *hw,
u16 *san_mac_offset)
{
int ret_val;
/*
* First read the EEPROM pointer to see if the MAC addresses are
* available.
*/
ret_val = hw->eeprom.ops.read(hw, IXGBE_SAN_MAC_ADDR_PTR,
san_mac_offset);
if (ret_val)
hw_err(hw, "eeprom read at offset %d failed\n",
IXGBE_SAN_MAC_ADDR_PTR);
return ret_val;
}
/**
* ixgbe_get_san_mac_addr_generic - SAN MAC address retrieval from the EEPROM
* @hw: pointer to hardware structure
* @san_mac_addr: SAN MAC address
*
* Reads the SAN MAC address from the EEPROM, if it's available. This is
* per-port, so set_lan_id() must be called before reading the addresses.
* set_lan_id() is called by identify_sfp(), but this cannot be relied
* upon for non-SFP connections, so we must call it here.
**/
int ixgbe_get_san_mac_addr_generic(struct ixgbe_hw *hw, u8 *san_mac_addr)
{
u16 san_mac_data, san_mac_offset;
int ret_val;
u8 i;
/*
* First read the EEPROM pointer to see if the MAC addresses are
* available. If they're not, no point in calling set_lan_id() here.
*/
ret_val = ixgbe_get_san_mac_addr_offset(hw, &san_mac_offset);
if (ret_val || san_mac_offset == 0 || san_mac_offset == 0xFFFF)
goto san_mac_addr_clr;
/* make sure we know which port we need to program */
hw->mac.ops.set_lan_id(hw);
/* apply the port offset to the address offset */
(hw->bus.func) ? (san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT1_OFFSET) :
(san_mac_offset += IXGBE_SAN_MAC_ADDR_PORT0_OFFSET);
for (i = 0; i < 3; i++) {
ret_val = hw->eeprom.ops.read(hw, san_mac_offset,
&san_mac_data);
if (ret_val) {
hw_err(hw, "eeprom read at offset %d failed\n",
san_mac_offset);
goto san_mac_addr_clr;
}
san_mac_addr[i * 2] = (u8)(san_mac_data);
san_mac_addr[i * 2 + 1] = (u8)(san_mac_data >> 8);
san_mac_offset++;
}
return 0;
san_mac_addr_clr:
/* No addresses available in this EEPROM. It's not necessarily an
* error though, so just wipe the local address and return.
*/
for (i = 0; i < 6; i++)
san_mac_addr[i] = 0xFF;
return ret_val;
}
/**
* ixgbe_get_pcie_msix_count_generic - Gets MSI-X vector count
* @hw: pointer to hardware structure
*
* Read PCIe configuration space, and get the MSI-X vector count from
* the capabilities table.
**/
u16 ixgbe_get_pcie_msix_count_generic(struct ixgbe_hw *hw)
{
u16 msix_count;
u16 max_msix_count;
u16 pcie_offset;
switch (hw->mac.type) {
case ixgbe_mac_82598EB:
pcie_offset = IXGBE_PCIE_MSIX_82598_CAPS;
max_msix_count = IXGBE_MAX_MSIX_VECTORS_82598;
break;
case ixgbe_mac_82599EB:
case ixgbe_mac_X540:
case ixgbe_mac_X550:
case ixgbe_mac_X550EM_x:
case ixgbe_mac_x550em_a:
pcie_offset = IXGBE_PCIE_MSIX_82599_CAPS;
max_msix_count = IXGBE_MAX_MSIX_VECTORS_82599;
break;
default:
return 1;
}
msix_count = ixgbe_read_pci_cfg_word(hw, pcie_offset);
if (ixgbe_removed(hw->hw_addr))
msix_count = 0;
msix_count &= IXGBE_PCIE_MSIX_TBL_SZ_MASK;
/* MSI-X count is zero-based in HW */
msix_count++;
if (msix_count > max_msix_count)
msix_count = max_msix_count;
return msix_count;
}
/**
* ixgbe_clear_vmdq_generic - Disassociate a VMDq pool index from a rx address
* @hw: pointer to hardware struct
* @rar: receive address register index to disassociate
* @vmdq: VMDq pool index to remove from the rar
**/
int ixgbe_clear_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
u32 mpsar_lo, mpsar_hi;
u32 rar_entries = hw->mac.num_rar_entries;
/* Make sure we are using a valid rar index range */
if (rar >= rar_entries) {
hw_dbg(hw, "RAR index %d is out of range.\n", rar);
return -EINVAL;
}
mpsar_lo = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
mpsar_hi = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
if (ixgbe_removed(hw->hw_addr))
return 0;
if (!mpsar_lo && !mpsar_hi)
return 0;
if (vmdq == IXGBE_CLEAR_VMDQ_ALL) {
if (mpsar_lo) {
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
mpsar_lo = 0;
}
if (mpsar_hi) {
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
mpsar_hi = 0;
}
} else if (vmdq < 32) {
mpsar_lo &= ~BIT(vmdq);
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar_lo);
} else {
mpsar_hi &= ~BIT(vmdq - 32);
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar_hi);
}
/* was that the last pool using this rar? */
if (mpsar_lo == 0 && mpsar_hi == 0 &&
rar != 0 && rar != hw->mac.san_mac_rar_index)
hw->mac.ops.clear_rar(hw, rar);
return 0;
}
/**
* ixgbe_set_vmdq_generic - Associate a VMDq pool index with a rx address
* @hw: pointer to hardware struct
* @rar: receive address register index to associate with a VMDq index
* @vmdq: VMDq pool index
**/
int ixgbe_set_vmdq_generic(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
{
u32 mpsar;
u32 rar_entries = hw->mac.num_rar_entries;
/* Make sure we are using a valid rar index range */
if (rar >= rar_entries) {
hw_dbg(hw, "RAR index %d is out of range.\n", rar);
return -EINVAL;
}
if (vmdq < 32) {
mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_LO(rar));
mpsar |= BIT(vmdq);
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), mpsar);
} else {
mpsar = IXGBE_READ_REG(hw, IXGBE_MPSAR_HI(rar));
mpsar |= BIT(vmdq - 32);
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), mpsar);
}
return 0;
}
/**
* ixgbe_set_vmdq_san_mac_generic - Associate VMDq pool index with a rx address
* @hw: pointer to hardware struct
* @vmdq: VMDq pool index
*
* This function should only be involved in the IOV mode.
* In IOV mode, Default pool is next pool after the number of
* VFs advertized and not 0.
* MPSAR table needs to be updated for SAN_MAC RAR [hw->mac.san_mac_rar_index]
**/
int ixgbe_set_vmdq_san_mac_generic(struct ixgbe_hw *hw, u32 vmdq)
{
u32 rar = hw->mac.san_mac_rar_index;
if (vmdq < 32) {
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), BIT(vmdq));
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), 0);
} else {
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_LO(rar), 0);
IXGBE_WRITE_REG(hw, IXGBE_MPSAR_HI(rar), BIT(vmdq - 32));
}
return 0;
}
/**
* ixgbe_init_uta_tables_generic - Initialize the Unicast Table Array
* @hw: pointer to hardware structure
**/
int ixgbe_init_uta_tables_generic(struct ixgbe_hw *hw)
{
int i;
for (i = 0; i < 128; i++)
IXGBE_WRITE_REG(hw, IXGBE_UTA(i), 0);
return 0;
}
/**
* ixgbe_find_vlvf_slot - find the vlanid or the first empty slot
* @hw: pointer to hardware structure
* @vlan: VLAN id to write to VLAN filter
* @vlvf_bypass: true to find vlanid only, false returns first empty slot if
* vlanid not found
*
* return the VLVF index where this VLAN id should be placed
*
**/
static int ixgbe_find_vlvf_slot(struct ixgbe_hw *hw, u32 vlan, bool vlvf_bypass)
{
int regindex, first_empty_slot;
u32 bits;
/* short cut the special case */
if (vlan == 0)
return 0;
/* if vlvf_bypass is set we don't want to use an empty slot, we
* will simply bypass the VLVF if there are no entries present in the
* VLVF that contain our VLAN
*/
first_empty_slot = vlvf_bypass ? -ENOSPC : 0;
/* add VLAN enable bit for comparison */
vlan |= IXGBE_VLVF_VIEN;
/* Search for the vlan id in the VLVF entries. Save off the first empty
* slot found along the way.
*
* pre-decrement loop covering (IXGBE_VLVF_ENTRIES - 1) .. 1
*/
for (regindex = IXGBE_VLVF_ENTRIES; --regindex;) {
bits = IXGBE_READ_REG(hw, IXGBE_VLVF(regindex));
if (bits == vlan)
return regindex;
if (!first_empty_slot && !bits)
first_empty_slot = regindex;
}
/* If we are here then we didn't find the VLAN. Return first empty
* slot we found during our search, else error.
*/
if (!first_empty_slot)
hw_dbg(hw, "No space in VLVF.\n");
return first_empty_slot ? : -ENOSPC;
}
/**
* ixgbe_set_vfta_generic - Set VLAN filter table
* @hw: pointer to hardware structure
* @vlan: VLAN id to write to VLAN filter
* @vind: VMDq output index that maps queue to VLAN id in VFVFB
* @vlan_on: boolean flag to turn on/off VLAN in VFVF
* @vlvf_bypass: boolean flag indicating updating default pool is okay
*
* Turn on/off specified VLAN in the VLAN filter table.
**/
int ixgbe_set_vfta_generic(struct ixgbe_hw *hw, u32 vlan, u32 vind,
bool vlan_on, bool vlvf_bypass)
{
u32 regidx, vfta_delta, vfta, bits;
int vlvf_index;
if ((vlan > 4095) || (vind > 63))
return -EINVAL;
/*
* this is a 2 part operation - first the VFTA, then the
* VLVF and VLVFB if VT Mode is set
* We don't write the VFTA until we know the VLVF part succeeded.
*/
/* Part 1
* The VFTA is a bitstring made up of 128 32-bit registers
* that enable the particular VLAN id, much like the MTA:
* bits[11-5]: which register
* bits[4-0]: which bit in the register
*/
regidx = vlan / 32;
vfta_delta = BIT(vlan % 32);
vfta = IXGBE_READ_REG(hw, IXGBE_VFTA(regidx));
/* vfta_delta represents the difference between the current value
* of vfta and the value we want in the register. Since the diff
* is an XOR mask we can just update vfta using an XOR.
*/
vfta_delta &= vlan_on ? ~vfta : vfta;
vfta ^= vfta_delta;
/* Part 2
* If VT Mode is set
* Either vlan_on
* make sure the vlan is in VLVF
* set the vind bit in the matching VLVFB
* Or !vlan_on
* clear the pool bit and possibly the vind
*/
if (!(IXGBE_READ_REG(hw, IXGBE_VT_CTL) & IXGBE_VT_CTL_VT_ENABLE))
goto vfta_update;
vlvf_index = ixgbe_find_vlvf_slot(hw, vlan, vlvf_bypass);
if (vlvf_index < 0) {
if (vlvf_bypass)
goto vfta_update;
return vlvf_index;
}
bits = IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32));
/* set the pool bit */
bits |= BIT(vind % 32);
if (vlan_on)
goto vlvf_update;
/* clear the pool bit */
bits ^= BIT(vind % 32);
if (!bits &&
!IXGBE_READ_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + 1 - vind / 32))) {
/* Clear VFTA first, then disable VLVF. Otherwise
* we run the risk of stray packets leaking into
* the PF via the default pool
*/
if (vfta_delta)
IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
/* disable VLVF and clear remaining bit from pool */
IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), 0);
IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), 0);
return 0;
}
/* If there are still bits set in the VLVFB registers
* for the VLAN ID indicated we need to see if the
* caller is requesting that we clear the VFTA entry bit.
* If the caller has requested that we clear the VFTA
* entry bit but there are still pools/VFs using this VLAN
* ID entry then ignore the request. We're not worried
* about the case where we're turning the VFTA VLAN ID
* entry bit on, only when requested to turn it off as
* there may be multiple pools and/or VFs using the
* VLAN ID entry. In that case we cannot clear the
* VFTA bit until all pools/VFs using that VLAN ID have also
* been cleared. This will be indicated by "bits" being
* zero.
*/
vfta_delta = 0;
vlvf_update:
/* record pool change and enable VLAN ID if not already enabled */
IXGBE_WRITE_REG(hw, IXGBE_VLVFB(vlvf_index * 2 + vind / 32), bits);
IXGBE_WRITE_REG(hw, IXGBE_VLVF(vlvf_index), IXGBE_VLVF_VIEN | vlan);
vfta_update:
/* Update VFTA now that we are ready for traffic */
if (vfta_delta)
IXGBE_WRITE_REG(hw, IXGBE_VFTA(regidx), vfta);
return 0;
}
/**
* ixgbe_clear_vfta_generic - Clear VLAN filter table
* @hw: pointer to hardware structure
*
* Clears the VLAN filter table, and the VMDq index associated with the filter
**/
int ixgbe_clear_vfta_generic(struct ixgbe_hw *hw)
{
u32 offset;
for (offset = 0; offset < hw->mac.vft_size; offset++)
IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0);
for (offset = 0; offset < IXGBE_VLVF_ENTRIES; offset++) {
IXGBE_WRITE_REG(hw, IXGBE_VLVF(offset), 0);
IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2), 0);
IXGBE_WRITE_REG(hw, IXGBE_VLVFB(offset * 2 + 1), 0);
}
return 0;
}
/**
* ixgbe_need_crosstalk_fix - Determine if we need to do cross talk fix
* @hw: pointer to hardware structure
*
* Contains the logic to identify if we need to verify link for the
* crosstalk fix
**/
static bool ixgbe_need_crosstalk_fix(struct ixgbe_hw *hw)
{
/* Does FW say we need the fix */
if (!hw->need_crosstalk_fix)
return false;
/* Only consider SFP+ PHYs i.e. media type fiber */
switch (hw->mac.ops.get_media_type(hw)) {
case ixgbe_media_type_fiber:
case ixgbe_media_type_fiber_qsfp:
break;
default:
return false;
}
return true;
}
/**
* ixgbe_check_mac_link_generic - Determine link and speed status
* @hw: pointer to hardware structure
* @speed: pointer to link speed
* @link_up: true when link is up
* @link_up_wait_to_complete: bool used to wait for link up or not
*
* Reads the links register to determine if link is up and the current speed
**/
int ixgbe_check_mac_link_generic(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
bool *link_up, bool link_up_wait_to_complete)
{
bool crosstalk_fix_active = ixgbe_need_crosstalk_fix(hw);
u32 links_reg, links_orig;
u32 i;
/* If Crosstalk fix enabled do the sanity check of making sure
* the SFP+ cage is full.
*/
if (crosstalk_fix_active) {
u32 sfp_cage_full;
switch (hw->mac.type) {
case ixgbe_mac_82599EB:
sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
IXGBE_ESDP_SDP2;
break;
case ixgbe_mac_X550EM_x:
case ixgbe_mac_x550em_a:
sfp_cage_full = IXGBE_READ_REG(hw, IXGBE_ESDP) &
IXGBE_ESDP_SDP0;
break;
default:
/* sanity check - No SFP+ devices here */
sfp_cage_full = false;
break;
}
if (!sfp_cage_full) {
*link_up = false;
*speed = IXGBE_LINK_SPEED_UNKNOWN;
return 0;
}
}
/* clear the old state */
links_orig = IXGBE_READ_REG(hw, IXGBE_LINKS);
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
if (links_orig != links_reg) {
hw_dbg(hw, "LINKS changed from %08X to %08X\n",
links_orig, links_reg);
}
if (link_up_wait_to_complete) {
for (i = 0; i < IXGBE_LINK_UP_TIME; i++) {
if (links_reg & IXGBE_LINKS_UP) {
*link_up = true;
break;
} else {
*link_up = false;
}
msleep(100);
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
}
} else {
if (links_reg & IXGBE_LINKS_UP) {
if (crosstalk_fix_active) {
/* Check the link state again after a delay
* to filter out spurious link up
* notifications.
*/
mdelay(5);
links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS);
if (!(links_reg & IXGBE_LINKS_UP)) {
*link_up = false;
*speed = IXGBE_LINK_SPEED_UNKNOWN;
return 0;
}
}
*link_up = true;
} else {
*link_up = false;
}
}
switch (links_reg & IXGBE_LINKS_SPEED_82599) {
case IXGBE_LINKS_SPEED_10G_82599:
if ((hw->mac.type >= ixgbe_mac_X550) &&
(links_reg & IXGBE_LINKS_SPEED_NON_STD))
*speed = IXGBE_LINK_SPEED_2_5GB_FULL;
else
*speed = IXGBE_LINK_SPEED_10GB_FULL;
break;
case IXGBE_LINKS_SPEED_1G_82599:
*speed = IXGBE_LINK_SPEED_1GB_FULL;
break;
case IXGBE_LINKS_SPEED_100_82599:
if ((hw->mac.type >= ixgbe_mac_X550) &&
(links_reg & IXGBE_LINKS_SPEED_NON_STD))
*speed = IXGBE_LINK_SPEED_5GB_FULL;
else
*speed = IXGBE_LINK_SPEED_100_FULL;
break;
case IXGBE_LINKS_SPEED_10_X550EM_A:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) {
*speed = IXGBE_LINK_SPEED_10_FULL;
}
break;
default:
*speed = IXGBE_LINK_SPEED_UNKNOWN;
}
return 0;
}
/**
* ixgbe_get_wwn_prefix_generic - Get alternative WWNN/WWPN prefix from
* the EEPROM
* @hw: pointer to hardware structure
* @wwnn_prefix: the alternative WWNN prefix
* @wwpn_prefix: the alternative WWPN prefix
*
* This function will read the EEPROM from the alternative SAN MAC address
* block to check the support for the alternative WWNN/WWPN prefix support.
**/
int ixgbe_get_wwn_prefix_generic(struct ixgbe_hw *hw, u16 *wwnn_prefix,
u16 *wwpn_prefix)
{
u16 offset, caps;
u16 alt_san_mac_blk_offset;
/* clear output first */
*wwnn_prefix = 0xFFFF;
*wwpn_prefix = 0xFFFF;
/* check if alternative SAN MAC is supported */
offset = IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR;
if (hw->eeprom.ops.read(hw, offset, &alt_san_mac_blk_offset))
goto wwn_prefix_err;
if ((alt_san_mac_blk_offset == 0) ||
(alt_san_mac_blk_offset == 0xFFFF))
return 0;
/* check capability in alternative san mac address block */
offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET;
if (hw->eeprom.ops.read(hw, offset, &caps))
goto wwn_prefix_err;
if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN))
return 0;
/* get the corresponding prefix for WWNN/WWPN */
offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET;
if (hw->eeprom.ops.read(hw, offset, wwnn_prefix))
hw_err(hw, "eeprom read at offset %d failed\n", offset);
offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET;
if (hw->eeprom.ops.read(hw, offset, wwpn_prefix))
goto wwn_prefix_err;
return 0;
wwn_prefix_err:
hw_err(hw, "eeprom read at offset %d failed\n", offset);
return 0;
}
/**
* ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
* @hw: pointer to hardware structure
* @enable: enable or disable switch for MAC anti-spoofing
* @vf: Virtual Function pool - VF Pool to set for MAC anti-spoofing
*
**/
void ixgbe_set_mac_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
{
int vf_target_reg = vf >> 3;
int vf_target_shift = vf % 8;
u32 pfvfspoof;
if (hw->mac.type == ixgbe_mac_82598EB)
return;
pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
if (enable)
pfvfspoof |= BIT(vf_target_shift);
else
pfvfspoof &= ~BIT(vf_target_shift);
IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
}
/**
* ixgbe_set_vlan_anti_spoofing - Enable/Disable VLAN anti-spoofing
* @hw: pointer to hardware structure
* @enable: enable or disable switch for VLAN anti-spoofing
* @vf: Virtual Function pool - VF Pool to set for VLAN anti-spoofing
*
**/
void ixgbe_set_vlan_anti_spoofing(struct ixgbe_hw *hw, bool enable, int vf)
{
int vf_target_reg = vf >> 3;
int vf_target_shift = vf % 8 + IXGBE_SPOOF_VLANAS_SHIFT;
u32 pfvfspoof;
if (hw->mac.type == ixgbe_mac_82598EB)
return;
pfvfspoof = IXGBE_READ_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg));
if (enable)
pfvfspoof |= BIT(vf_target_shift);
else
pfvfspoof &= ~BIT(vf_target_shift);
IXGBE_WRITE_REG(hw, IXGBE_PFVFSPOOF(vf_target_reg), pfvfspoof);
}
/**
* ixgbe_get_device_caps_generic - Get additional device capabilities
* @hw: pointer to hardware structure
* @device_caps: the EEPROM word with the extra device capabilities
*
* This function will read the EEPROM location for the device capabilities,
* and return the word through device_caps.
**/
int ixgbe_get_device_caps_generic(struct ixgbe_hw *hw, u16 *device_caps)
{
hw->eeprom.ops.read(hw, IXGBE_DEVICE_CAPS, device_caps);
return 0;
}
/**
* ixgbe_set_rxpba_generic - Initialize RX packet buffer
* @hw: pointer to hardware structure
* @num_pb: number of packet buffers to allocate
* @headroom: reserve n KB of headroom
* @strategy: packet buffer allocation strategy
**/
void ixgbe_set_rxpba_generic(struct ixgbe_hw *hw,
int num_pb,
u32 headroom,
int strategy)
{
u32 pbsize = hw->mac.rx_pb_size;
int i = 0;
u32 rxpktsize, txpktsize, txpbthresh;
/* Reserve headroom */
pbsize -= headroom;
if (!num_pb)
num_pb = 1;
/* Divide remaining packet buffer space amongst the number
* of packet buffers requested using supplied strategy.
*/
switch (strategy) {
case (PBA_STRATEGY_WEIGHTED):
/* pba_80_48 strategy weight first half of packet buffer with
* 5/8 of the packet buffer space.
*/
rxpktsize = ((pbsize * 5 * 2) / (num_pb * 8));
pbsize -= rxpktsize * (num_pb / 2);
rxpktsize <<= IXGBE_RXPBSIZE_SHIFT;
for (; i < (num_pb / 2); i++)
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
fallthrough; /* configure remaining packet buffers */
case (PBA_STRATEGY_EQUAL):
/* Divide the remaining Rx packet buffer evenly among the TCs */
rxpktsize = (pbsize / (num_pb - i)) << IXGBE_RXPBSIZE_SHIFT;
for (; i < num_pb; i++)
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize);
break;
default:
break;
}
/*
* Setup Tx packet buffer and threshold equally for all TCs
* TXPBTHRESH register is set in K so divide by 1024 and subtract
* 10 since the largest packet we support is just over 9K.
*/
txpktsize = IXGBE_TXPBSIZE_MAX / num_pb;
txpbthresh = (txpktsize / 1024) - IXGBE_TXPKT_SIZE_MAX;
for (i = 0; i < num_pb; i++) {
IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), txpktsize);
IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), txpbthresh);
}
/* Clear unused TCs, if any, to zero buffer size*/
for (; i < IXGBE_MAX_PB; i++) {
IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), 0);
IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), 0);
IXGBE_WRITE_REG(hw, IXGBE_TXPBTHRESH(i), 0);
}
}
/**
* ixgbe_calculate_checksum - Calculate checksum for buffer
* @buffer: pointer to EEPROM
* @length: size of EEPROM to calculate a checksum for
*
* Calculates the checksum for some buffer on a specified length. The
* checksum calculated is returned.
**/
u8 ixgbe_calculate_checksum(u8 *buffer, u32 length)
{
u32 i;
u8 sum = 0;
if (!buffer)
return 0;
for (i = 0; i < length; i++)
sum += buffer[i];
return (u8) (0 - sum);
}
/**
* ixgbe_hic_unlocked - Issue command to manageability block unlocked
* @hw: pointer to the HW structure
* @buffer: command to write and where the return status will be placed
* @length: length of buffer, must be multiple of 4 bytes
* @timeout: time in ms to wait for command completion
*
* Communicates with the manageability block. On success return 0
* else returns semaphore error when encountering an error acquiring
* semaphore, -EINVAL when incorrect parameters passed or -EIO when
* command fails.
*
* This function assumes that the IXGBE_GSSR_SW_MNG_SM semaphore is held
* by the caller.
**/
int ixgbe_hic_unlocked(struct ixgbe_hw *hw, u32 *buffer, u32 length,
u32 timeout)
{
u32 hicr, i, fwsts;
u16 dword_len;
if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
return -EINVAL;
}
/* Set bit 9 of FWSTS clearing FW reset indication */
fwsts = IXGBE_READ_REG(hw, IXGBE_FWSTS);
IXGBE_WRITE_REG(hw, IXGBE_FWSTS, fwsts | IXGBE_FWSTS_FWRI);
/* Check that the host interface is enabled. */
hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
if (!(hicr & IXGBE_HICR_EN)) {
hw_dbg(hw, "IXGBE_HOST_EN bit disabled.\n");
return -EIO;
}
/* Calculate length in DWORDs. We must be DWORD aligned */
if (length % sizeof(u32)) {
hw_dbg(hw, "Buffer length failure, not aligned to dword");
return -EINVAL;
}
dword_len = length >> 2;
/* The device driver writes the relevant command block
* into the ram area.
*/
for (i = 0; i < dword_len; i++)
IXGBE_WRITE_REG_ARRAY(hw, IXGBE_FLEX_MNG,
i, (__force u32)cpu_to_le32(buffer[i]));
/* Setting this bit tells the ARC that a new command is pending. */
IXGBE_WRITE_REG(hw, IXGBE_HICR, hicr | IXGBE_HICR_C);
for (i = 0; i < timeout; i++) {
hicr = IXGBE_READ_REG(hw, IXGBE_HICR);
if (!(hicr & IXGBE_HICR_C))
break;
usleep_range(1000, 2000);
}
/* Check command successful completion. */
if ((timeout && i == timeout) ||
!(IXGBE_READ_REG(hw, IXGBE_HICR) & IXGBE_HICR_SV))
return -EIO;
return 0;
}
/**
* ixgbe_host_interface_command - Issue command to manageability block
* @hw: pointer to the HW structure
* @buffer: contains the command to write and where the return status will
* be placed
* @length: length of buffer, must be multiple of 4 bytes
* @timeout: time in ms to wait for command completion
* @return_data: read and return data from the buffer (true) or not (false)
* Needed because FW structures are big endian and decoding of
* these fields can be 8 bit or 16 bit based on command. Decoding
* is not easily understood without making a table of commands.
* So we will leave this up to the caller to read back the data
* in these cases.
*
* Communicates with the manageability block. On success return 0
* else return -EIO or -EINVAL.
**/
int ixgbe_host_interface_command(struct ixgbe_hw *hw, void *buffer,
u32 length, u32 timeout,
bool return_data)
{
u32 hdr_size = sizeof(struct ixgbe_hic_hdr);
struct ixgbe_hic_hdr *hdr = buffer;
u16 buf_len, dword_len;
u32 *u32arr = buffer;
int status;
u32 bi;
if (!length || length > IXGBE_HI_MAX_BLOCK_BYTE_LENGTH) {
hw_dbg(hw, "Buffer length failure buffersize-%d.\n", length);
return -EINVAL;
}
/* Take management host interface semaphore */
status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
if (status)
return status;
status = ixgbe_hic_unlocked(hw, buffer, length, timeout);
if (status)
goto rel_out;
if (!return_data)
goto rel_out;
/* Calculate length in DWORDs */
dword_len = hdr_size >> 2;
/* first pull in the header so we know the buffer length */
for (bi = 0; bi < dword_len; bi++) {
u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
le32_to_cpus(&u32arr[bi]);
}
/* If there is any thing in data position pull it in */
buf_len = hdr->buf_len;
if (!buf_len)
goto rel_out;
if (length < round_up(buf_len, 4) + hdr_size) {
hw_dbg(hw, "Buffer not large enough for reply message.\n");
status = -EIO;
goto rel_out;
}
/* Calculate length in DWORDs, add 3 for odd lengths */
dword_len = (buf_len + 3) >> 2;
/* Pull in the rest of the buffer (bi is where we left off) */
for (; bi <= dword_len; bi++) {
u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi);
le32_to_cpus(&u32arr[bi]);
}
rel_out:
hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_SW_MNG_SM);
return status;
}
/**
* ixgbe_set_fw_drv_ver_generic - Sends driver version to firmware
* @hw: pointer to the HW structure
* @maj: driver version major number
* @min: driver version minor number
* @build: driver version build number
* @sub: driver version sub build number
* @len: length of driver_ver string
* @driver_ver: driver string
*
* Sends driver version number to firmware through the manageability
* block. On success return 0
* else returns -EBUSY when encountering an error acquiring
* semaphore or -EIO when command fails.
**/
int ixgbe_set_fw_drv_ver_generic(struct ixgbe_hw *hw, u8 maj, u8 min,
u8 build, u8 sub, __always_unused u16 len,
__always_unused const char *driver_ver)
{
struct ixgbe_hic_drv_info fw_cmd;
int ret_val;
int i;
fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN;
fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
fw_cmd.port_num = hw->bus.func;
fw_cmd.ver_maj = maj;
fw_cmd.ver_min = min;
fw_cmd.ver_build = build;
fw_cmd.ver_sub = sub;
fw_cmd.hdr.checksum = 0;
fw_cmd.pad = 0;
fw_cmd.pad2 = 0;
fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
(FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
ret_val = ixgbe_host_interface_command(hw, &fw_cmd,
sizeof(fw_cmd),
IXGBE_HI_COMMAND_TIMEOUT,
true);
if (ret_val != 0)
continue;
if (fw_cmd.hdr.cmd_or_resp.ret_status ==
FW_CEM_RESP_STATUS_SUCCESS)
ret_val = 0;
else
ret_val = -EIO;
break;
}
return ret_val;
}
/**
* ixgbe_clear_tx_pending - Clear pending TX work from the PCIe fifo
* @hw: pointer to the hardware structure
*
* The 82599 and x540 MACs can experience issues if TX work is still pending
* when a reset occurs. This function prevents this by flushing the PCIe
* buffers on the system.
**/
void ixgbe_clear_tx_pending(struct ixgbe_hw *hw)
{
u32 gcr_ext, hlreg0, i, poll;
u16 value;
/*
* If double reset is not requested then all transactions should
* already be clear and as such there is no work to do
*/
if (!(hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED))
return;
/*
* Set loopback enable to prevent any transmits from being sent
* should the link come up. This assumes that the RXCTRL.RXEN bit
* has already been cleared.
*/
hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0);
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0 | IXGBE_HLREG0_LPBK);
/* wait for a last completion before clearing buffers */
IXGBE_WRITE_FLUSH(hw);
usleep_range(3000, 6000);
/* Before proceeding, make sure that the PCIe block does not have
* transactions pending.
*/
poll = ixgbe_pcie_timeout_poll(hw);
for (i = 0; i < poll; i++) {
usleep_range(100, 200);
value = ixgbe_read_pci_cfg_word(hw, IXGBE_PCI_DEVICE_STATUS);
if (ixgbe_removed(hw->hw_addr))
break;
if (!(value & IXGBE_PCI_DEVICE_STATUS_TRANSACTION_PENDING))
break;
}
/* initiate cleaning flow for buffers in the PCIe transaction layer */
gcr_ext = IXGBE_READ_REG(hw, IXGBE_GCR_EXT);
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT,
gcr_ext | IXGBE_GCR_EXT_BUFFERS_CLEAR);
/* Flush all writes and allow 20usec for all transactions to clear */
IXGBE_WRITE_FLUSH(hw);
udelay(20);
/* restore previous register values */
IXGBE_WRITE_REG(hw, IXGBE_GCR_EXT, gcr_ext);
IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0);
}
static const u8 ixgbe_emc_temp_data[4] = {
IXGBE_EMC_INTERNAL_DATA,
IXGBE_EMC_DIODE1_DATA,
IXGBE_EMC_DIODE2_DATA,
IXGBE_EMC_DIODE3_DATA
};
static const u8 ixgbe_emc_therm_limit[4] = {
IXGBE_EMC_INTERNAL_THERM_LIMIT,
IXGBE_EMC_DIODE1_THERM_LIMIT,
IXGBE_EMC_DIODE2_THERM_LIMIT,
IXGBE_EMC_DIODE3_THERM_LIMIT
};
/**
* ixgbe_get_ets_data - Extracts the ETS bit data
* @hw: pointer to hardware structure
* @ets_cfg: extected ETS data
* @ets_offset: offset of ETS data
*
* Returns error code.
**/
static int ixgbe_get_ets_data(struct ixgbe_hw *hw, u16 *ets_cfg,
u16 *ets_offset)
{
int status;
status = hw->eeprom.ops.read(hw, IXGBE_ETS_CFG, ets_offset);
if (status)
return status;
if ((*ets_offset == 0x0000) || (*ets_offset == 0xFFFF))
return -EOPNOTSUPP;
status = hw->eeprom.ops.read(hw, *ets_offset, ets_cfg);
if (status)
return status;
if ((*ets_cfg & IXGBE_ETS_TYPE_MASK) != IXGBE_ETS_TYPE_EMC_SHIFTED)
return -EOPNOTSUPP;
return 0;
}
/**
* ixgbe_get_thermal_sensor_data_generic - Gathers thermal sensor data
* @hw: pointer to hardware structure
*
* Returns the thermal sensor data structure
**/
int ixgbe_get_thermal_sensor_data_generic(struct ixgbe_hw *hw)
{
u16 ets_offset;
u16 ets_sensor;
u8 num_sensors;
u16 ets_cfg;
int status;
u8 i;
struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
/* Only support thermal sensors attached to physical port 0 */
if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
return -EOPNOTSUPP;
status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
if (status)
return status;
num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
if (num_sensors > IXGBE_MAX_SENSORS)
num_sensors = IXGBE_MAX_SENSORS;
for (i = 0; i < num_sensors; i++) {
u8 sensor_index;
u8 sensor_location;
status = hw->eeprom.ops.read(hw, (ets_offset + 1 + i),
&ets_sensor);
if (status)
return status;
sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
ets_sensor);
sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
ets_sensor);
if (sensor_location != 0) {
status = hw->phy.ops.read_i2c_byte(hw,
ixgbe_emc_temp_data[sensor_index],
IXGBE_I2C_THERMAL_SENSOR_ADDR,
&data->sensor[i].temp);
if (status)
return status;
}
}
return 0;
}
/**
* ixgbe_init_thermal_sensor_thresh_generic - Inits thermal sensor thresholds
* @hw: pointer to hardware structure
*
* Inits the thermal sensor thresholds according to the NVM map
* and save off the threshold and location values into mac.thermal_sensor_data
**/
int ixgbe_init_thermal_sensor_thresh_generic(struct ixgbe_hw *hw)
{
struct ixgbe_thermal_sensor_data *data = &hw->mac.thermal_sensor_data;
u8 low_thresh_delta;
u8 num_sensors;
u8 therm_limit;
u16 ets_sensor;
u16 ets_offset;
u16 ets_cfg;
int status;
u8 i;
memset(data, 0, sizeof(struct ixgbe_thermal_sensor_data));
/* Only support thermal sensors attached to physical port 0 */
if ((IXGBE_READ_REG(hw, IXGBE_STATUS) & IXGBE_STATUS_LAN_ID_1))
return -EOPNOTSUPP;
status = ixgbe_get_ets_data(hw, &ets_cfg, &ets_offset);
if (status)
return status;
low_thresh_delta = FIELD_GET(IXGBE_ETS_LTHRES_DELTA_MASK, ets_cfg);
num_sensors = (ets_cfg & IXGBE_ETS_NUM_SENSORS_MASK);
if (num_sensors > IXGBE_MAX_SENSORS)
num_sensors = IXGBE_MAX_SENSORS;
for (i = 0; i < num_sensors; i++) {
u8 sensor_index;
u8 sensor_location;
if (hw->eeprom.ops.read(hw, ets_offset + 1 + i, &ets_sensor)) {
hw_err(hw, "eeprom read at offset %d failed\n",
ets_offset + 1 + i);
continue;
}
sensor_index = FIELD_GET(IXGBE_ETS_DATA_INDEX_MASK,
ets_sensor);
sensor_location = FIELD_GET(IXGBE_ETS_DATA_LOC_MASK,
ets_sensor);
therm_limit = ets_sensor & IXGBE_ETS_DATA_HTHRESH_MASK;
hw->phy.ops.write_i2c_byte(hw,
ixgbe_emc_therm_limit[sensor_index],
IXGBE_I2C_THERMAL_SENSOR_ADDR, therm_limit);
if (sensor_location == 0)
continue;
data->sensor[i].location = sensor_location;
data->sensor[i].caution_thresh = therm_limit;
data->sensor[i].max_op_thresh = therm_limit - low_thresh_delta;
}
return 0;
}
/**
* ixgbe_get_orom_version - Return option ROM from EEPROM
*
* @hw: pointer to hardware structure
* @nvm_ver: pointer to output structure
*
* if valid option ROM version, nvm_ver->or_valid set to true
* else nvm_ver->or_valid is false.
**/
void ixgbe_get_orom_version(struct ixgbe_hw *hw,
struct ixgbe_nvm_version *nvm_ver)
{
u16 offset, eeprom_cfg_blkh, eeprom_cfg_blkl;
nvm_ver->or_valid = false;
/* Option Rom may or may not be present. Start with pointer */
hw->eeprom.ops.read(hw, NVM_OROM_OFFSET, &offset);
/* make sure offset is valid */
if (offset == 0x0 || offset == NVM_INVALID_PTR)
return;
hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_HI, &eeprom_cfg_blkh);
hw->eeprom.ops.read(hw, offset + NVM_OROM_BLK_LOW, &eeprom_cfg_blkl);
/* option rom exists and is valid */
if ((eeprom_cfg_blkl | eeprom_cfg_blkh) == 0x0 ||
eeprom_cfg_blkl == NVM_VER_INVALID ||
eeprom_cfg_blkh == NVM_VER_INVALID)
return;
nvm_ver->or_valid = true;
nvm_ver->or_major = eeprom_cfg_blkl >> NVM_OROM_SHIFT;
nvm_ver->or_build = (eeprom_cfg_blkl << NVM_OROM_SHIFT) |
(eeprom_cfg_blkh >> NVM_OROM_SHIFT);
nvm_ver->or_patch = eeprom_cfg_blkh & NVM_OROM_PATCH_MASK;
}
/**
* ixgbe_get_oem_prod_version - Etrack ID from EEPROM
* @hw: pointer to hardware structure
* @nvm_ver: pointer to output structure
*
* if valid OEM product version, nvm_ver->oem_valid set to true
* else nvm_ver->oem_valid is false.
**/
void ixgbe_get_oem_prod_version(struct ixgbe_hw *hw,
struct ixgbe_nvm_version *nvm_ver)
{
u16 rel_num, prod_ver, mod_len, cap, offset;
nvm_ver->oem_valid = false;
hw->eeprom.ops.read(hw, NVM_OEM_PROD_VER_PTR, &offset);
/* Return is offset to OEM Product Version block is invalid */
if (offset == 0x0 || offset == NVM_INVALID_PTR)
return;
/* Read product version block */
hw->eeprom.ops.read(hw, offset, &mod_len);
hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_CAP_OFF, &cap);
/* Return if OEM product version block is invalid */
if (mod_len != NVM_OEM_PROD_VER_MOD_LEN ||
(cap & NVM_OEM_PROD_VER_CAP_MASK) != 0x0)
return;
hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_L, &prod_ver);
hw->eeprom.ops.read(hw, offset + NVM_OEM_PROD_VER_OFF_H, &rel_num);
/* Return if version is invalid */
if ((rel_num | prod_ver) == 0x0 ||
rel_num == NVM_VER_INVALID || prod_ver == NVM_VER_INVALID)
return;
nvm_ver->oem_major = prod_ver >> NVM_VER_SHIFT;
nvm_ver->oem_minor = prod_ver & NVM_VER_MASK;
nvm_ver->oem_release = rel_num;
nvm_ver->oem_valid = true;
}
/**
* ixgbe_get_etk_id - Return Etrack ID from EEPROM
*
* @hw: pointer to hardware structure
* @nvm_ver: pointer to output structure
*
* word read errors will return 0xFFFF
**/
void ixgbe_get_etk_id(struct ixgbe_hw *hw,
struct ixgbe_nvm_version *nvm_ver)
{
u16 etk_id_l, etk_id_h;
if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_LOW, &etk_id_l))
etk_id_l = NVM_VER_INVALID;
if (hw->eeprom.ops.read(hw, NVM_ETK_OFF_HI, &etk_id_h))
etk_id_h = NVM_VER_INVALID;
/* The word order for the version format is determined by high order
* word bit 15.
*/
if ((etk_id_h & NVM_ETK_VALID) == 0) {
nvm_ver->etk_id = etk_id_h;
nvm_ver->etk_id |= (etk_id_l << NVM_ETK_SHIFT);
} else {
nvm_ver->etk_id = etk_id_l;
nvm_ver->etk_id |= (etk_id_h << NVM_ETK_SHIFT);
}
}
void ixgbe_disable_rx_generic(struct ixgbe_hw *hw)
{
u32 rxctrl;
rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
if (rxctrl & IXGBE_RXCTRL_RXEN) {
if (hw->mac.type != ixgbe_mac_82598EB) {
u32 pfdtxgswc;
pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
hw->mac.set_lben = true;
} else {
hw->mac.set_lben = false;
}
}
rxctrl &= ~IXGBE_RXCTRL_RXEN;
IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
}
}
void ixgbe_enable_rx_generic(struct ixgbe_hw *hw)
{
u32 rxctrl;
rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, (rxctrl | IXGBE_RXCTRL_RXEN));
if (hw->mac.type != ixgbe_mac_82598EB) {
if (hw->mac.set_lben) {
u32 pfdtxgswc;
pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
pfdtxgswc |= IXGBE_PFDTXGSWC_VT_LBEN;
IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
hw->mac.set_lben = false;
}
}
}
/** ixgbe_mng_present - returns true when management capability is present
* @hw: pointer to hardware structure
**/
bool ixgbe_mng_present(struct ixgbe_hw *hw)
{
u32 fwsm;
if (hw->mac.type < ixgbe_mac_82599EB)
return false;
fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM(hw));
return !!(fwsm & IXGBE_FWSM_FW_MODE_PT);
}
/**
* ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed
* @hw: pointer to hardware structure
* @speed: new link speed
* @autoneg_wait_to_complete: true when waiting for completion is needed
*
* Set the link speed in the MAC and/or PHY register and restarts link.
*/
int ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw,
ixgbe_link_speed speed,
bool autoneg_wait_to_complete)
{
ixgbe_link_speed highest_link_speed = IXGBE_LINK_SPEED_UNKNOWN;
ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
bool autoneg, link_up = false;
u32 speedcnt = 0;
int status = 0;
u32 i = 0;
/* Mask off requested but non-supported speeds */
status = hw->mac.ops.get_link_capabilities(hw, &link_speed, &autoneg);
if (status)
return status;
speed &= link_speed;
/* Try each speed one by one, highest priority first. We do this in
* software because 10Gb fiber doesn't support speed autonegotiation.
*/
if (speed & IXGBE_LINK_SPEED_10GB_FULL) {
speedcnt++;
highest_link_speed = IXGBE_LINK_SPEED_10GB_FULL;
/* Set the module link speed */
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
hw->mac.ops.set_rate_select_speed(hw,
IXGBE_LINK_SPEED_10GB_FULL);
break;
case ixgbe_media_type_fiber_qsfp:
/* QSFP module automatically detects MAC link speed */
break;
default:
hw_dbg(hw, "Unexpected media type\n");
break;
}
/* Allow module to change analog characteristics (1G->10G) */
msleep(40);
status = hw->mac.ops.setup_mac_link(hw,
IXGBE_LINK_SPEED_10GB_FULL,
autoneg_wait_to_complete);
if (status)
return status;
/* Flap the Tx laser if it has not already been done */
if (hw->mac.ops.flap_tx_laser)
hw->mac.ops.flap_tx_laser(hw);
/* Wait for the controller to acquire link. Per IEEE 802.3ap,
* Section 73.10.2, we may have to wait up to 500ms if KR is
* attempted. 82599 uses the same timing for 10g SFI.
*/
for (i = 0; i < 5; i++) {
/* Wait for the link partner to also set speed */
msleep(100);
/* If we have link, just jump out */
status = hw->mac.ops.check_link(hw, &link_speed,
&link_up, false);
if (status)
return status;
if (link_up)
goto out;
}
}
if (speed & IXGBE_LINK_SPEED_1GB_FULL) {
speedcnt++;
if (highest_link_speed == IXGBE_LINK_SPEED_UNKNOWN)
highest_link_speed = IXGBE_LINK_SPEED_1GB_FULL;
/* Set the module link speed */
switch (hw->phy.media_type) {
case ixgbe_media_type_fiber:
hw->mac.ops.set_rate_select_speed(hw,
IXGBE_LINK_SPEED_1GB_FULL);
break;
case ixgbe_media_type_fiber_qsfp:
/* QSFP module automatically detects link speed */
break;
default:
hw_dbg(hw, "Unexpected media type\n");
break;
}
/* Allow module to change analog characteristics (10G->1G) */
msleep(40);
status = hw->mac.ops.setup_mac_link(hw,
IXGBE_LINK_SPEED_1GB_FULL,
autoneg_wait_to_complete);
if (status)
return status;
/* Flap the Tx laser if it has not already been done */
if (hw->mac.ops.flap_tx_laser)
hw->mac.ops.flap_tx_laser(hw);
/* Wait for the link partner to also set speed */
msleep(100);
/* If we have link, just jump out */
status = hw->mac.ops.check_link(hw, &link_speed, &link_up,
false);
if (status)
return status;
if (link_up)
goto out;
}
/* We didn't get link. Configure back to the highest speed we tried,
* (if there was more than one). We call ourselves back with just the
* single highest speed that the user requested.
*/
if (speedcnt > 1)
status = ixgbe_setup_mac_link_multispeed_fiber(hw,
highest_link_speed,
autoneg_wait_to_complete);
out:
/* Set autoneg_advertised value based on input link speed */
hw->phy.autoneg_advertised = 0;
if (speed & IXGBE_LINK_SPEED_10GB_FULL)
hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL;
if (speed & IXGBE_LINK_SPEED_1GB_FULL)
hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL;
return status;
}
/**
* ixgbe_set_soft_rate_select_speed - Set module link speed
* @hw: pointer to hardware structure
* @speed: link speed to set
*
* Set module link speed via the soft rate select.
*/
void ixgbe_set_soft_rate_select_speed(struct ixgbe_hw *hw,
ixgbe_link_speed speed)
{
u8 rs, eeprom_data;
int status;
switch (speed) {
case IXGBE_LINK_SPEED_10GB_FULL:
/* one bit mask same as setting on */
rs = IXGBE_SFF_SOFT_RS_SELECT_10G;
break;
case IXGBE_LINK_SPEED_1GB_FULL:
rs = IXGBE_SFF_SOFT_RS_SELECT_1G;
break;
default:
hw_dbg(hw, "Invalid fixed module speed\n");
return;
}
/* Set RS0 */
status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
IXGBE_I2C_EEPROM_DEV_ADDR2,
&eeprom_data);
if (status) {
hw_dbg(hw, "Failed to read Rx Rate Select RS0\n");
return;
}
eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_OSCB,
IXGBE_I2C_EEPROM_DEV_ADDR2,
eeprom_data);
if (status) {
hw_dbg(hw, "Failed to write Rx Rate Select RS0\n");
return;
}
/* Set RS1 */
status = hw->phy.ops.read_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
IXGBE_I2C_EEPROM_DEV_ADDR2,
&eeprom_data);
if (status) {
hw_dbg(hw, "Failed to read Rx Rate Select RS1\n");
return;
}
eeprom_data = (eeprom_data & ~IXGBE_SFF_SOFT_RS_SELECT_MASK) | rs;
status = hw->phy.ops.write_i2c_byte(hw, IXGBE_SFF_SFF_8472_ESCB,
IXGBE_I2C_EEPROM_DEV_ADDR2,
eeprom_data);
if (status) {
hw_dbg(hw, "Failed to write Rx Rate Select RS1\n");
return;
}
}