/* SPDX-License-Identifier: GPL-2.0 */
/* Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
* Copyright (C) 2018-2024 Linaro Ltd.
*/
#ifndef _IPA_H_
#define _IPA_H_
#include <linux/notifier.h>
#include <linux/types.h>
#include "gsi.h"
#include "ipa_endpoint.h"
#include "ipa_mem.h"
#include "ipa_qmi.h"
#include "ipa_version.h"
struct net_device;
struct ipa_interrupt;
struct ipa_power;
struct ipa_smp2p;
/**
* struct ipa - IPA information
* @gsi: Embedded GSI structure
* @version: IPA hardware version
* @dev: IPA device pointer
* @completion: Used to signal pipeline clear transfer complete
* @nb: Notifier block used for remoteproc SSR
* @notifier: Remoteproc SSR notifier
* @smp2p: SMP2P information
* @power: IPA power information
* @table_addr: DMA address of filter/route table content
* @table_virt: Virtual address of filter/route table content
* @route_count: Total number of entries in a routing table
* @modem_route_count: Number of modem entries in a routing table
* @filter_count: Maximum number of entries in a filter table
* @interrupt: IPA Interrupt information
* @uc_powered: true if power is active by proxy for microcontroller
* @uc_loaded: true after microcontroller has reported it's ready
* @reg_virt: Virtual address used for IPA register access
* @regs: IPA register definitions
* @mem_addr: DMA address of IPA-local memory space
* @mem_virt: Virtual address of IPA-local memory space
* @mem_offset: Offset from @mem_virt used for access to IPA memory
* @mem_size: Total size (bytes) of memory at @mem_virt
* @mem_count: Number of entries in the mem array
* @mem: Array of IPA-local memory region descriptors
* @imem_iova: I/O virtual address of IPA region in IMEM
* @imem_size: Size of IMEM region
* @smem_iova: I/O virtual address of IPA region in SMEM
* @smem_size: Size of SMEM region
* @zero_addr: DMA address of preallocated zero-filled memory
* @zero_virt: Virtual address of preallocated zero-filled memory
* @zero_size: Size (bytes) of preallocated zero-filled memory
* @endpoint_count: Number of defined bits in most bitmaps below
* @available_count: Number of defined bits in the available bitmap
* @defined: Bitmap of endpoints defined in config data
* @available: Bitmap of endpoints supported by hardware
* @filtered: Bitmap of endpoints that support filtering
* @set_up: Bitmap of endpoints that are set up for use
* @enabled: Bitmap of currently enabled endpoints
* @modem_tx_count: Number of defined modem TX endoints
* @endpoint: Array of endpoint information
* @channel_map: Mapping of GSI channel to IPA endpoint
* @name_map: Mapping of IPA endpoint name to IPA endpoint
* @setup_complete: Flag indicating whether setup stage has completed
* @modem_state: State of modem (stopped, running)
* @modem_netdev: Network device structure used for modem
* @qmi: QMI information
*/
struct ipa {
struct gsi gsi;
enum ipa_version version;
struct device *dev;
struct completion completion;
struct notifier_block nb;
void *notifier;
struct ipa_smp2p *smp2p;
struct ipa_power *power;
dma_addr_t table_addr;
__le64 *table_virt;
u32 route_count;
u32 modem_route_count;
u32 filter_count;
struct ipa_interrupt *interrupt;
bool uc_powered;
bool uc_loaded;
void __iomem *reg_virt;
const struct regs *regs;
dma_addr_t mem_addr;
void *mem_virt;
u32 mem_offset;
u32 mem_size;
u32 mem_count;
const struct ipa_mem *mem;
unsigned long imem_iova;
size_t imem_size;
unsigned long smem_iova;
size_t smem_size;
dma_addr_t zero_addr;
void *zero_virt;
size_t zero_size;
/* Bitmaps indicating endpoint state */
u32 endpoint_count;
u32 available_count;
unsigned long *defined; /* Defined in configuration data */
unsigned long *available; /* Supported by hardware */
u64 filtered; /* Support filtering (AP and modem) */
unsigned long *set_up;
unsigned long *enabled;
u32 modem_tx_count;
struct ipa_endpoint endpoint[IPA_ENDPOINT_MAX];
struct ipa_endpoint *channel_map[GSI_CHANNEL_COUNT_MAX];
struct ipa_endpoint *name_map[IPA_ENDPOINT_COUNT];
bool setup_complete;
atomic_t modem_state; /* enum ipa_modem_state */
struct net_device *modem_netdev;
struct ipa_qmi qmi;
};
/**
* ipa_setup() - Perform IPA setup
* @ipa: IPA pointer
*
* IPA initialization is broken into stages: init; config; and setup.
* (These have inverses exit, deconfig, and teardown.)
*
* Activities performed at the init stage can be done without requiring
* any access to IPA hardware. Activities performed at the config stage
* require IPA power, because they involve access to IPA registers.
* The setup stage is performed only after the GSI hardware is ready
* (more on this below). The setup stage allows the AP to perform
* more complex initialization by issuing "immediate commands" using
* a special interface to the IPA.
*
* This function, @ipa_setup(), starts the setup stage.
*
* In order for the GSI hardware to be functional it needs firmware to be
* loaded (in addition to some other low-level initialization). This early
* GSI initialization can be done either by Trust Zone on the AP or by the
* modem.
*
* If it's done by Trust Zone, the AP loads the GSI firmware and supplies
* it to Trust Zone to verify and install. When this completes, if
* verification was successful, the GSI layer is ready and ipa_setup()
* implements the setup phase of initialization.
*
* If the modem performs early GSI initialization, the AP needs to know
* when this has occurred. An SMP2P interrupt is used for this purpose,
* and receipt of that interrupt triggers the call to ipa_setup().
*/
int ipa_setup(struct ipa *ipa);
#endif /* _IPA_H_ */
Codebase Browser
linux