// SPDX-License-Identifier: GPL-2.0-or-later
/*
* STTS751 sensor driver
*
* Copyright (C) 2016-2017 Istituto Italiano di Tecnologia - RBCS - EDL
* Robotics, Brain and Cognitive Sciences department
* Electronic Design Laboratory
*
* Written by Andrea Merello <[email protected]>
*
* Based on LM95241 driver and LM90 driver
*/
#include <linux/bitops.h>
#include <linux/err.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/jiffies.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/property.h>
#include <linux/slab.h>
#include <linux/sysfs.h>
#include <linux/util_macros.h>
#define DEVNAME "stts751"
static const unsigned short normal_i2c[] = {
0x48, 0x49, 0x38, 0x39, /* STTS751-0 */
0x4A, 0x4B, 0x3A, 0x3B, /* STTS751-1 */
I2C_CLIENT_END };
#define STTS751_REG_TEMP_H 0x00
#define STTS751_REG_STATUS 0x01
#define STTS751_STATUS_TRIPT BIT(0)
#define STTS751_STATUS_TRIPL BIT(5)
#define STTS751_STATUS_TRIPH BIT(6)
#define STTS751_REG_TEMP_L 0x02
#define STTS751_REG_CONF 0x03
#define STTS751_CONF_RES_MASK 0x0C
#define STTS751_CONF_RES_SHIFT 2
#define STTS751_CONF_EVENT_DIS BIT(7)
#define STTS751_CONF_STOP BIT(6)
#define STTS751_REG_RATE 0x04
#define STTS751_REG_HLIM_H 0x05
#define STTS751_REG_HLIM_L 0x06
#define STTS751_REG_LLIM_H 0x07
#define STTS751_REG_LLIM_L 0x08
#define STTS751_REG_TLIM 0x20
#define STTS751_REG_HYST 0x21
#define STTS751_REG_SMBUS_TO 0x22
#define STTS751_REG_PROD_ID 0xFD
#define STTS751_REG_MAN_ID 0xFE
#define STTS751_REG_REV_ID 0xFF
#define STTS751_0_PROD_ID 0x00
#define STTS751_1_PROD_ID 0x01
#define ST_MAN_ID 0x53
/*
* Possible update intervals are (in mS):
* 16000, 8000, 4000, 2000, 1000, 500, 250, 125, 62.5, 31.25
* However we are not going to complicate things too much and we stick to the
* approx value in mS.
*/
static const int stts751_intervals[] = {
16000, 8000, 4000, 2000, 1000, 500, 250, 125, 63, 31
};
static const struct i2c_device_id stts751_id[] = {
{ "stts751" },
{ }
};
static const struct of_device_id __maybe_unused stts751_of_match[] = {
{ .compatible = "st,stts751" },
{ },
};
MODULE_DEVICE_TABLE(of, stts751_of_match);
struct stts751_priv {
struct device *dev;
struct i2c_client *client;
struct mutex access_lock;
u8 interval;
int res;
int event_max, event_min;
int therm;
int hyst;
int temp;
unsigned long last_update, last_alert_update;
u8 config;
bool min_alert, max_alert, therm_trip;
bool data_valid, alert_valid;
bool notify_max, notify_min;
};
/*
* These functions converts temperature from HW format to integer format and
* vice-vers. They are (mostly) taken from lm90 driver. Unit is in mC.
*/
static int stts751_to_deg(s16 hw_val)
{
return hw_val * 125 / 32;
}
static s32 stts751_to_hw(int val)
{
return DIV_ROUND_CLOSEST(val, 125) * 32;
}
static int stts751_adjust_resolution(struct stts751_priv *priv)
{
u8 res;
switch (priv->interval) {
case 9:
/* 10 bits */
res = 0;
break;
case 8:
/* 11 bits */
res = 1;
break;
default:
/* 12 bits */
res = 3;
break;
}
if (priv->res == res)
return 0;
priv->config &= ~STTS751_CONF_RES_MASK;
priv->config |= res << STTS751_CONF_RES_SHIFT;
dev_dbg(&priv->client->dev, "setting res %d. config %x",
res, priv->config);
priv->res = res;
return i2c_smbus_write_byte_data(priv->client,
STTS751_REG_CONF, priv->config);
}
static int stts751_update_temp(struct stts751_priv *priv)
{
s32 integer1, integer2, frac;
/*
* There is a trick here, like in the lm90 driver. We have to read two
* registers to get the sensor temperature, but we have to beware a
* conversion could occur between the readings. We could use the
* one-shot conversion register, but we don't want to do this (disables
* hardware monitoring). So the solution used here is to read the high
* byte once, then the low byte, then the high byte again. If the new
* high byte matches the old one, then we have a valid reading. Else we
* have to read the low byte again, and now we believe we have a correct
* reading.
*/
integer1 = i2c_smbus_read_byte_data(priv->client, STTS751_REG_TEMP_H);
if (integer1 < 0) {
dev_dbg(&priv->client->dev,
"I2C read failed (temp H). ret: %x\n", integer1);
return integer1;
}
frac = i2c_smbus_read_byte_data(priv->client, STTS751_REG_TEMP_L);
if (frac < 0) {
dev_dbg(&priv->client->dev,
"I2C read failed (temp L). ret: %x\n", frac);
return frac;
}
integer2 = i2c_smbus_read_byte_data(priv->client, STTS751_REG_TEMP_H);
if (integer2 < 0) {
dev_dbg(&priv->client->dev,
"I2C 2nd read failed (temp H). ret: %x\n", integer2);
return integer2;
}
if (integer1 != integer2) {
frac = i2c_smbus_read_byte_data(priv->client,
STTS751_REG_TEMP_L);
if (frac < 0) {
dev_dbg(&priv->client->dev,
"I2C 2nd read failed (temp L). ret: %x\n",
frac);
return frac;
}
}
priv->temp = stts751_to_deg((integer1 << 8) | frac);
return 0;
}
static int stts751_set_temp_reg16(struct stts751_priv *priv, int temp,
u8 hreg, u8 lreg)
{
s32 hwval;
int ret;
hwval = stts751_to_hw(temp);
ret = i2c_smbus_write_byte_data(priv->client, hreg, hwval >> 8);
if (ret)
return ret;
return i2c_smbus_write_byte_data(priv->client, lreg, hwval & 0xff);
}
static int stts751_set_temp_reg8(struct stts751_priv *priv, int temp, u8 reg)
{
s32 hwval;
hwval = stts751_to_hw(temp);
return i2c_smbus_write_byte_data(priv->client, reg, hwval >> 8);
}
static int stts751_read_reg16(struct stts751_priv *priv, int *temp,
u8 hreg, u8 lreg)
{
int integer, frac;
integer = i2c_smbus_read_byte_data(priv->client, hreg);
if (integer < 0)
return integer;
frac = i2c_smbus_read_byte_data(priv->client, lreg);
if (frac < 0)
return frac;
*temp = stts751_to_deg((integer << 8) | frac);
return 0;
}
static int stts751_read_reg8(struct stts751_priv *priv, int *temp, u8 reg)
{
int integer;
integer = i2c_smbus_read_byte_data(priv->client, reg);
if (integer < 0)
return integer;
*temp = stts751_to_deg(integer << 8);
return 0;
}
/*
* Update alert flags without waiting for cache to expire. We detects alerts
* immediately for the sake of the alert handler; we still need to deal with
* caching to workaround the fact that alarm flags int the status register,
* despite what the datasheet claims, gets always cleared on read.
*/
static int stts751_update_alert(struct stts751_priv *priv)
{
int ret;
bool conv_done;
int cache_time = msecs_to_jiffies(stts751_intervals[priv->interval]);
/*
* Add another 10% because if we run faster than the HW conversion
* rate we will end up in reporting incorrectly alarms.
*/
cache_time += cache_time / 10;
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_STATUS);
if (ret < 0)
return ret;
dev_dbg(&priv->client->dev, "status reg %x\n", ret);
conv_done = ret & (STTS751_STATUS_TRIPH | STTS751_STATUS_TRIPL);
/*
* Reset the cache if the cache time expired, or if we are sure
* we have valid data from a device conversion, or if we know
* our cache has been never written.
*
* Note that when the cache has been never written the point is
* to correctly initialize the timestamp, rather than clearing
* the cache values.
*
* Note that updating the cache timestamp when we get an alarm flag
* is required, otherwise we could incorrectly report alarms to be zero.
*/
if (time_after(jiffies, priv->last_alert_update + cache_time) ||
conv_done || !priv->alert_valid) {
priv->max_alert = false;
priv->min_alert = false;
priv->alert_valid = true;
priv->last_alert_update = jiffies;
dev_dbg(&priv->client->dev, "invalidating alert cache\n");
}
priv->max_alert |= !!(ret & STTS751_STATUS_TRIPH);
priv->min_alert |= !!(ret & STTS751_STATUS_TRIPL);
priv->therm_trip = !!(ret & STTS751_STATUS_TRIPT);
dev_dbg(&priv->client->dev, "max_alert: %d, min_alert: %d, therm_trip: %d\n",
priv->max_alert, priv->min_alert, priv->therm_trip);
return 0;
}
static void stts751_alert(struct i2c_client *client,
enum i2c_alert_protocol type, unsigned int data)
{
int ret;
struct stts751_priv *priv = i2c_get_clientdata(client);
if (type != I2C_PROTOCOL_SMBUS_ALERT)
return;
dev_dbg(&client->dev, "alert!");
mutex_lock(&priv->access_lock);
ret = stts751_update_alert(priv);
if (ret < 0) {
/* default to worst case */
priv->max_alert = true;
priv->min_alert = true;
dev_warn(priv->dev,
"Alert received, but can't communicate to the device. Triggering all alarms!");
}
if (priv->max_alert) {
if (priv->notify_max)
dev_notice(priv->dev, "got alert for HIGH temperature");
priv->notify_max = false;
/* unblock alert poll */
sysfs_notify(&priv->dev->kobj, NULL, "temp1_max_alarm");
}
if (priv->min_alert) {
if (priv->notify_min)
dev_notice(priv->dev, "got alert for LOW temperature");
priv->notify_min = false;
/* unblock alert poll */
sysfs_notify(&priv->dev->kobj, NULL, "temp1_min_alarm");
}
if (priv->min_alert || priv->max_alert)
kobject_uevent(&priv->dev->kobj, KOBJ_CHANGE);
mutex_unlock(&priv->access_lock);
}
static int stts751_update(struct stts751_priv *priv)
{
int ret;
int cache_time = msecs_to_jiffies(stts751_intervals[priv->interval]);
if (time_after(jiffies, priv->last_update + cache_time) ||
!priv->data_valid) {
ret = stts751_update_temp(priv);
if (ret)
return ret;
ret = stts751_update_alert(priv);
if (ret)
return ret;
priv->data_valid = true;
priv->last_update = jiffies;
}
return 0;
}
static ssize_t max_alarm_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
int ret;
struct stts751_priv *priv = dev_get_drvdata(dev);
mutex_lock(&priv->access_lock);
ret = stts751_update(priv);
if (!ret)
priv->notify_max = true;
mutex_unlock(&priv->access_lock);
if (ret < 0)
return ret;
return sysfs_emit(buf, "%d\n", priv->max_alert);
}
static ssize_t min_alarm_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
int ret;
struct stts751_priv *priv = dev_get_drvdata(dev);
mutex_lock(&priv->access_lock);
ret = stts751_update(priv);
if (!ret)
priv->notify_min = true;
mutex_unlock(&priv->access_lock);
if (ret < 0)
return ret;
return sysfs_emit(buf, "%d\n", priv->min_alert);
}
static ssize_t input_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
int ret;
struct stts751_priv *priv = dev_get_drvdata(dev);
mutex_lock(&priv->access_lock);
ret = stts751_update(priv);
mutex_unlock(&priv->access_lock);
if (ret < 0)
return ret;
return sysfs_emit(buf, "%d\n", priv->temp);
}
static ssize_t therm_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct stts751_priv *priv = dev_get_drvdata(dev);
return sysfs_emit(buf, "%d\n", priv->therm);
}
static ssize_t therm_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int ret;
long temp;
struct stts751_priv *priv = dev_get_drvdata(dev);
if (kstrtol(buf, 10, &temp) < 0)
return -EINVAL;
/* HW works in range -64C to +127.937C */
temp = clamp_val(temp, -64000, 127937);
mutex_lock(&priv->access_lock);
ret = stts751_set_temp_reg8(priv, temp, STTS751_REG_TLIM);
if (ret)
goto exit;
dev_dbg(&priv->client->dev, "setting therm %ld", temp);
/*
* hysteresis reg is relative to therm, so the HW does not need to be
* adjusted, we need to update our local copy only.
*/
priv->hyst = temp - (priv->therm - priv->hyst);
priv->therm = temp;
exit:
mutex_unlock(&priv->access_lock);
if (ret)
return ret;
return count;
}
static ssize_t hyst_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct stts751_priv *priv = dev_get_drvdata(dev);
return sysfs_emit(buf, "%d\n", priv->hyst);
}
static ssize_t hyst_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int ret;
long temp;
struct stts751_priv *priv = dev_get_drvdata(dev);
if (kstrtol(buf, 10, &temp) < 0)
return -EINVAL;
mutex_lock(&priv->access_lock);
/* HW works in range -64C to +127.937C */
temp = clamp_val(temp, -64000, priv->therm);
priv->hyst = temp;
dev_dbg(&priv->client->dev, "setting hyst %ld", temp);
temp = priv->therm - temp;
ret = stts751_set_temp_reg8(priv, temp, STTS751_REG_HYST);
mutex_unlock(&priv->access_lock);
if (ret)
return ret;
return count;
}
static ssize_t therm_trip_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
int ret;
struct stts751_priv *priv = dev_get_drvdata(dev);
mutex_lock(&priv->access_lock);
ret = stts751_update(priv);
mutex_unlock(&priv->access_lock);
if (ret < 0)
return ret;
return sysfs_emit(buf, "%d\n", priv->therm_trip);
}
static ssize_t max_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct stts751_priv *priv = dev_get_drvdata(dev);
return sysfs_emit(buf, "%d\n", priv->event_max);
}
static ssize_t max_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int ret;
long temp;
struct stts751_priv *priv = dev_get_drvdata(dev);
if (kstrtol(buf, 10, &temp) < 0)
return -EINVAL;
mutex_lock(&priv->access_lock);
/* HW works in range -64C to +127.937C */
temp = clamp_val(temp, priv->event_min, 127937);
ret = stts751_set_temp_reg16(priv, temp,
STTS751_REG_HLIM_H, STTS751_REG_HLIM_L);
if (ret)
goto exit;
dev_dbg(&priv->client->dev, "setting event max %ld", temp);
priv->event_max = temp;
ret = count;
exit:
mutex_unlock(&priv->access_lock);
return ret;
}
static ssize_t min_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct stts751_priv *priv = dev_get_drvdata(dev);
return sysfs_emit(buf, "%d\n", priv->event_min);
}
static ssize_t min_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int ret;
long temp;
struct stts751_priv *priv = dev_get_drvdata(dev);
if (kstrtol(buf, 10, &temp) < 0)
return -EINVAL;
mutex_lock(&priv->access_lock);
/* HW works in range -64C to +127.937C */
temp = clamp_val(temp, -64000, priv->event_max);
ret = stts751_set_temp_reg16(priv, temp,
STTS751_REG_LLIM_H, STTS751_REG_LLIM_L);
if (ret)
goto exit;
dev_dbg(&priv->client->dev, "setting event min %ld", temp);
priv->event_min = temp;
ret = count;
exit:
mutex_unlock(&priv->access_lock);
return ret;
}
static ssize_t interval_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct stts751_priv *priv = dev_get_drvdata(dev);
return sysfs_emit(buf, "%d\n",
stts751_intervals[priv->interval]);
}
static ssize_t interval_store(struct device *dev,
struct device_attribute *attr, const char *buf,
size_t count)
{
unsigned long val;
int idx;
int ret = count;
struct stts751_priv *priv = dev_get_drvdata(dev);
if (kstrtoul(buf, 10, &val) < 0)
return -EINVAL;
idx = find_closest_descending(val, stts751_intervals,
ARRAY_SIZE(stts751_intervals));
dev_dbg(&priv->client->dev, "setting interval. req:%lu, idx: %d, val: %d",
val, idx, stts751_intervals[idx]);
mutex_lock(&priv->access_lock);
if (priv->interval == idx)
goto exit;
/*
* In early development stages I've become suspicious about the chip
* starting to misbehave if I ever set, even briefly, an invalid
* configuration. While I'm not sure this is really needed, be
* conservative and set rate/resolution in such an order that avoids
* passing through an invalid configuration.
*/
/* speed up: lower the resolution, then modify convrate */
if (priv->interval < idx) {
dev_dbg(&priv->client->dev, "lower resolution, then modify convrate");
priv->interval = idx;
ret = stts751_adjust_resolution(priv);
if (ret)
goto exit;
}
ret = i2c_smbus_write_byte_data(priv->client, STTS751_REG_RATE, idx);
if (ret)
goto exit;
/* slow down: modify convrate, then raise resolution */
if (priv->interval != idx) {
dev_dbg(&priv->client->dev, "modify convrate, then raise resolution");
priv->interval = idx;
ret = stts751_adjust_resolution(priv);
if (ret)
goto exit;
}
ret = count;
exit:
mutex_unlock(&priv->access_lock);
return ret;
}
static int stts751_detect(struct i2c_client *new_client,
struct i2c_board_info *info)
{
struct i2c_adapter *adapter = new_client->adapter;
const char *name;
int tmp;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
return -ENODEV;
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_MAN_ID);
if (tmp != ST_MAN_ID)
return -ENODEV;
/* lower temperaure registers always have bits 0-3 set to zero */
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_TEMP_L);
if (tmp & 0xf)
return -ENODEV;
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_HLIM_L);
if (tmp & 0xf)
return -ENODEV;
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_LLIM_L);
if (tmp & 0xf)
return -ENODEV;
/* smbus timeout register always have bits 0-7 set to zero */
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_SMBUS_TO);
if (tmp & 0x7f)
return -ENODEV;
tmp = i2c_smbus_read_byte_data(new_client, STTS751_REG_PROD_ID);
switch (tmp) {
case STTS751_0_PROD_ID:
name = "STTS751-0";
break;
case STTS751_1_PROD_ID:
name = "STTS751-1";
break;
default:
return -ENODEV;
}
dev_dbg(&new_client->dev, "Chip %s detected", name);
strscpy(info->type, stts751_id[0].name, I2C_NAME_SIZE);
return 0;
}
static int stts751_read_chip_config(struct stts751_priv *priv)
{
int ret;
int tmp;
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_CONF);
if (ret < 0)
return ret;
priv->config = ret;
priv->res = (ret & STTS751_CONF_RES_MASK) >> STTS751_CONF_RES_SHIFT;
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_RATE);
if (ret < 0)
return ret;
if (ret >= ARRAY_SIZE(stts751_intervals)) {
dev_err(priv->dev, "Unrecognized conversion rate 0x%x\n", ret);
return -ENODEV;
}
priv->interval = ret;
ret = stts751_read_reg16(priv, &priv->event_max,
STTS751_REG_HLIM_H, STTS751_REG_HLIM_L);
if (ret)
return ret;
ret = stts751_read_reg16(priv, &priv->event_min,
STTS751_REG_LLIM_H, STTS751_REG_LLIM_L);
if (ret)
return ret;
ret = stts751_read_reg8(priv, &priv->therm, STTS751_REG_TLIM);
if (ret)
return ret;
ret = stts751_read_reg8(priv, &tmp, STTS751_REG_HYST);
if (ret)
return ret;
priv->hyst = priv->therm - tmp;
return 0;
}
static SENSOR_DEVICE_ATTR_RO(temp1_input, input, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_min, min, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_max, max, 0);
static SENSOR_DEVICE_ATTR_RO(temp1_min_alarm, min_alarm, 0);
static SENSOR_DEVICE_ATTR_RO(temp1_max_alarm, max_alarm, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_crit, therm, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_crit_hyst, hyst, 0);
static SENSOR_DEVICE_ATTR_RO(temp1_crit_alarm, therm_trip, 0);
static SENSOR_DEVICE_ATTR_RW(update_interval, interval, 0);
static struct attribute *stts751_attrs[] = {
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp1_min.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_crit.dev_attr.attr,
&sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
&sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
&sensor_dev_attr_update_interval.dev_attr.attr,
NULL
};
ATTRIBUTE_GROUPS(stts751);
static int stts751_probe(struct i2c_client *client)
{
struct stts751_priv *priv;
int ret;
bool smbus_nto;
int rev_id;
priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->client = client;
priv->notify_max = true;
priv->notify_min = true;
i2c_set_clientdata(client, priv);
mutex_init(&priv->access_lock);
if (device_property_present(&client->dev,
"smbus-timeout-disable")) {
smbus_nto = device_property_read_bool(&client->dev,
"smbus-timeout-disable");
ret = i2c_smbus_write_byte_data(client, STTS751_REG_SMBUS_TO,
smbus_nto ? 0 : 0x80);
if (ret)
return ret;
}
rev_id = i2c_smbus_read_byte_data(client, STTS751_REG_REV_ID);
if (rev_id < 0)
return -ENODEV;
if (rev_id != 0x1) {
dev_dbg(&client->dev, "Chip revision 0x%x is untested\n",
rev_id);
}
ret = stts751_read_chip_config(priv);
if (ret)
return ret;
priv->config &= ~(STTS751_CONF_STOP | STTS751_CONF_EVENT_DIS);
ret = i2c_smbus_write_byte_data(client, STTS751_REG_CONF, priv->config);
if (ret)
return ret;
priv->dev = devm_hwmon_device_register_with_groups(&client->dev,
client->name, priv,
stts751_groups);
return PTR_ERR_OR_ZERO(priv->dev);
}
MODULE_DEVICE_TABLE(i2c, stts751_id);
static struct i2c_driver stts751_driver = {
.class = I2C_CLASS_HWMON,
.driver = {
.name = DEVNAME,
.of_match_table = of_match_ptr(stts751_of_match),
},
.probe = stts751_probe,
.id_table = stts751_id,
.detect = stts751_detect,
.alert = stts751_alert,
.address_list = normal_i2c,
};
module_i2c_driver(stts751_driver);
MODULE_AUTHOR("Andrea Merello <[email protected]>");
MODULE_DESCRIPTION("STTS751 sensor driver");
MODULE_LICENSE("GPL");
Codebase Browser
linux