// SPDX-License-Identifier: GPL-2.0-or-later
/*
* via686a.c - Part of lm_sensors, Linux kernel modules
* for hardware monitoring
*
* Copyright (c) 1998 - 2002 Frodo Looijaard <[email protected]>,
* Kyösti Mälkki <[email protected]>,
* Mark Studebaker <[email protected]>,
* and Bob Dougherty <[email protected]>
*
* (Some conversion-factor data were contributed by Jonathan Teh Soon Yew
* <[email protected]> and Alex van Kaam <[email protected]>.)
*/
/*
* Supports the Via VT82C686A, VT82C686B south bridges.
* Reports all as a 686A.
* Warning - only supports a single device.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/jiffies.h>
#include <linux/platform_device.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/mutex.h>
#include <linux/sysfs.h>
#include <linux/acpi.h>
#include <linux/io.h>
#define DRIVER_NAME "via686a"
/*
* If force_addr is set to anything different from 0, we forcibly enable
* the device at the given address.
*/
static unsigned short force_addr;
module_param(force_addr, ushort, 0);
MODULE_PARM_DESC(force_addr,
"Initialize the base address of the sensors");
static struct platform_device *pdev;
/*
* The Via 686a southbridge has a LM78-like chip integrated on the same IC.
* This driver is a customized copy of lm78.c
*/
/* Many VIA686A constants specified below */
/* Length of ISA address segment */
#define VIA686A_EXTENT 0x80
#define VIA686A_BASE_REG 0x70
#define VIA686A_ENABLE_REG 0x74
/* The VIA686A registers */
/* ins numbered 0-4 */
#define VIA686A_REG_IN_MAX(nr) (0x2b + ((nr) * 2))
#define VIA686A_REG_IN_MIN(nr) (0x2c + ((nr) * 2))
#define VIA686A_REG_IN(nr) (0x22 + (nr))
/* fans numbered 1-2 */
#define VIA686A_REG_FAN_MIN(nr) (0x3a + (nr))
#define VIA686A_REG_FAN(nr) (0x28 + (nr))
/* temps numbered 1-3 */
static const u8 VIA686A_REG_TEMP[] = { 0x20, 0x21, 0x1f };
static const u8 VIA686A_REG_TEMP_OVER[] = { 0x39, 0x3d, 0x1d };
static const u8 VIA686A_REG_TEMP_HYST[] = { 0x3a, 0x3e, 0x1e };
/* bits 7-6 */
#define VIA686A_REG_TEMP_LOW1 0x4b
/* 2 = bits 5-4, 3 = bits 7-6 */
#define VIA686A_REG_TEMP_LOW23 0x49
#define VIA686A_REG_ALARM1 0x41
#define VIA686A_REG_ALARM2 0x42
#define VIA686A_REG_FANDIV 0x47
#define VIA686A_REG_CONFIG 0x40
/*
* The following register sets temp interrupt mode (bits 1-0 for temp1,
* 3-2 for temp2, 5-4 for temp3). Modes are:
* 00 interrupt stays as long as value is out-of-range
* 01 interrupt is cleared once register is read (default)
* 10 comparator mode- like 00, but ignores hysteresis
* 11 same as 00
*/
#define VIA686A_REG_TEMP_MODE 0x4b
/* We'll just assume that you want to set all 3 simultaneously: */
#define VIA686A_TEMP_MODE_MASK 0x3F
#define VIA686A_TEMP_MODE_CONTINUOUS 0x00
/*
* Conversions. Limit checking is only done on the TO_REG
* variants.
*
******** VOLTAGE CONVERSIONS (Bob Dougherty) ********
* From HWMon.cpp (Copyright 1998-2000 Jonathan Teh Soon Yew):
* voltagefactor[0]=1.25/2628; (2628/1.25=2102.4) // Vccp
* voltagefactor[1]=1.25/2628; (2628/1.25=2102.4) // +2.5V
* voltagefactor[2]=1.67/2628; (2628/1.67=1573.7) // +3.3V
* voltagefactor[3]=2.6/2628; (2628/2.60=1010.8) // +5V
* voltagefactor[4]=6.3/2628; (2628/6.30=417.14) // +12V
* in[i]=(data[i+2]*25.0+133)*voltagefactor[i];
* That is:
* volts = (25*regVal+133)*factor
* regVal = (volts/factor-133)/25
* (These conversions were contributed by Jonathan Teh Soon Yew
* <[email protected]>)
*/
static inline u8 IN_TO_REG(long val, int in_num)
{
/*
* To avoid floating point, we multiply constants by 10 (100 for +12V).
* Rounding is done (120500 is actually 133000 - 12500).
* Remember that val is expressed in 0.001V/bit, which is why we divide
* by an additional 10000 (100000 for +12V): 1000 for val and 10 (100)
* for the constants.
*/
if (in_num <= 1)
return (u8) clamp_val((val * 21024 - 1205000) / 250000, 0, 255);
else if (in_num == 2)
return (u8) clamp_val((val * 15737 - 1205000) / 250000, 0, 255);
else if (in_num == 3)
return (u8) clamp_val((val * 10108 - 1205000) / 250000, 0, 255);
else
return (u8) clamp_val((val * 41714 - 12050000) / 2500000, 0,
255);
}
static inline long IN_FROM_REG(u8 val, int in_num)
{
/*
* To avoid floating point, we multiply constants by 10 (100 for +12V).
* We also multiply them by 1000 because we want 0.001V/bit for the
* output value. Rounding is done.
*/
if (in_num <= 1)
return (long) ((250000 * val + 1330000 + 21024 / 2) / 21024);
else if (in_num == 2)
return (long) ((250000 * val + 1330000 + 15737 / 2) / 15737);
else if (in_num == 3)
return (long) ((250000 * val + 1330000 + 10108 / 2) / 10108);
else
return (long) ((2500000 * val + 13300000 + 41714 / 2) / 41714);
}
/********* FAN RPM CONVERSIONS ********/
/*
* Higher register values = slower fans (the fan's strobe gates a counter).
* But this chip saturates back at 0, not at 255 like all the other chips.
* So, 0 means 0 RPM
*/
static inline u8 FAN_TO_REG(long rpm, int div)
{
if (rpm == 0)
return 0;
rpm = clamp_val(rpm, 1, 1000000);
return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 255);
}
#define FAN_FROM_REG(val, div) ((val) == 0 ? 0 : (val) == 255 ? 0 : 1350000 / \
((val) * (div)))
/******** TEMP CONVERSIONS (Bob Dougherty) *********/
/*
* linear fits from HWMon.cpp (Copyright 1998-2000 Jonathan Teh Soon Yew)
* if(temp<169)
* return double(temp)*0.427-32.08;
* else if(temp>=169 && temp<=202)
* return double(temp)*0.582-58.16;
* else
* return double(temp)*0.924-127.33;
*
* A fifth-order polynomial fits the unofficial data (provided by Alex van
* Kaam <[email protected]>) a bit better. It also give more reasonable
* numbers on my machine (ie. they agree with what my BIOS tells me).
* Here's the fifth-order fit to the 8-bit data:
* temp = 1.625093e-10*val^5 - 1.001632e-07*val^4 + 2.457653e-05*val^3 -
* 2.967619e-03*val^2 + 2.175144e-01*val - 7.090067e+0.
*
* (2000-10-25- RFD: thanks to Uwe Andersen <[email protected]> for
* finding my typos in this formula!)
*
* Alas, none of the elegant function-fit solutions will work because we
* aren't allowed to use floating point in the kernel and doing it with
* integers doesn't provide enough precision. So we'll do boring old
* look-up table stuff. The unofficial data (see below) have effectively
* 7-bit resolution (they are rounded to the nearest degree). I'm assuming
* that the transfer function of the device is monotonic and smooth, so a
* smooth function fit to the data will allow us to get better precision.
* I used the 5th-order poly fit described above and solved for
* VIA register values 0-255. I *10 before rounding, so we get tenth-degree
* precision. (I could have done all 1024 values for our 10-bit readings,
* but the function is very linear in the useful range (0-80 deg C), so
* we'll just use linear interpolation for 10-bit readings.) So, temp_lut
* is the temp at via register values 0-255:
*/
static const s16 temp_lut[] = {
-709, -688, -667, -646, -627, -607, -589, -570, -553, -536, -519,
-503, -487, -471, -456, -442, -428, -414, -400, -387, -375,
-362, -350, -339, -327, -316, -305, -295, -285, -275, -265,
-255, -246, -237, -229, -220, -212, -204, -196, -188, -180,
-173, -166, -159, -152, -145, -139, -132, -126, -120, -114,
-108, -102, -96, -91, -85, -80, -74, -69, -64, -59, -54, -49,
-44, -39, -34, -29, -25, -20, -15, -11, -6, -2, 3, 7, 12, 16,
20, 25, 29, 33, 37, 42, 46, 50, 54, 59, 63, 67, 71, 75, 79, 84,
88, 92, 96, 100, 104, 109, 113, 117, 121, 125, 130, 134, 138,
142, 146, 151, 155, 159, 163, 168, 172, 176, 181, 185, 189,
193, 198, 202, 206, 211, 215, 219, 224, 228, 232, 237, 241,
245, 250, 254, 259, 263, 267, 272, 276, 281, 285, 290, 294,
299, 303, 307, 312, 316, 321, 325, 330, 334, 339, 344, 348,
353, 357, 362, 366, 371, 376, 380, 385, 390, 395, 399, 404,
409, 414, 419, 423, 428, 433, 438, 443, 449, 454, 459, 464,
469, 475, 480, 486, 491, 497, 502, 508, 514, 520, 526, 532,
538, 544, 551, 557, 564, 571, 578, 584, 592, 599, 606, 614,
621, 629, 637, 645, 654, 662, 671, 680, 689, 698, 708, 718,
728, 738, 749, 759, 770, 782, 793, 805, 818, 830, 843, 856,
870, 883, 898, 912, 927, 943, 958, 975, 991, 1008, 1026, 1044,
1062, 1081, 1101, 1121, 1141, 1162, 1184, 1206, 1229, 1252,
1276, 1301, 1326, 1352, 1378, 1406, 1434, 1462
};
/*
* the original LUT values from Alex van Kaam <[email protected]>
* (for via register values 12-240):
* {-50,-49,-47,-45,-43,-41,-39,-38,-37,-35,-34,-33,-32,-31,
* -30,-29,-28,-27,-26,-25,-24,-24,-23,-22,-21,-20,-20,-19,-18,-17,-17,-16,-15,
* -15,-14,-14,-13,-12,-12,-11,-11,-10,-9,-9,-8,-8,-7,-7,-6,-6,-5,-5,-4,-4,-3,
* -3,-2,-2,-1,-1,0,0,1,1,1,3,3,3,4,4,4,5,5,5,6,6,7,7,8,8,9,9,9,10,10,11,11,12,
* 12,12,13,13,13,14,14,15,15,16,16,16,17,17,18,18,19,19,20,20,21,21,21,22,22,
* 22,23,23,24,24,25,25,26,26,26,27,27,27,28,28,29,29,30,30,30,31,31,32,32,33,
* 33,34,34,35,35,35,36,36,37,37,38,38,39,39,40,40,41,41,42,42,43,43,44,44,45,
* 45,46,46,47,48,48,49,49,50,51,51,52,52,53,53,54,55,55,56,57,57,58,59,59,60,
* 61,62,62,63,64,65,66,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,83,84,
* 85,86,88,89,91,92,94,96,97,99,101,103,105,107,109,110};
*
*
* Here's the reverse LUT. I got it by doing a 6-th order poly fit (needed
* an extra term for a good fit to these inverse data!) and then
* solving for each temp value from -50 to 110 (the useable range for
* this chip). Here's the fit:
* viaRegVal = -1.160370e-10*val^6 +3.193693e-08*val^5 - 1.464447e-06*val^4
* - 2.525453e-04*val^3 + 1.424593e-02*val^2 + 2.148941e+00*val +7.275808e+01)
* Note that n=161:
*/
static const u8 via_lut[] = {
12, 12, 13, 14, 14, 15, 16, 16, 17, 18, 18, 19, 20, 20, 21, 22, 23,
23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 35, 36, 37, 39, 40,
41, 43, 45, 46, 48, 49, 51, 53, 55, 57, 59, 60, 62, 64, 66,
69, 71, 73, 75, 77, 79, 82, 84, 86, 88, 91, 93, 95, 98, 100,
103, 105, 107, 110, 112, 115, 117, 119, 122, 124, 126, 129,
131, 134, 136, 138, 140, 143, 145, 147, 150, 152, 154, 156,
158, 160, 162, 164, 166, 168, 170, 172, 174, 176, 178, 180,
182, 183, 185, 187, 188, 190, 192, 193, 195, 196, 198, 199,
200, 202, 203, 205, 206, 207, 208, 209, 210, 211, 212, 213,
214, 215, 216, 217, 218, 219, 220, 221, 222, 222, 223, 224,
225, 226, 226, 227, 228, 228, 229, 230, 230, 231, 232, 232,
233, 233, 234, 235, 235, 236, 236, 237, 237, 238, 238, 239,
239, 240
};
/*
* Converting temps to (8-bit) hyst and over registers
* No interpolation here.
* The +50 is because the temps start at -50
*/
static inline u8 TEMP_TO_REG(long val)
{
return via_lut[val <= -50000 ? 0 : val >= 110000 ? 160 :
(val < 0 ? val - 500 : val + 500) / 1000 + 50];
}
/* for 8-bit temperature hyst and over registers */
#define TEMP_FROM_REG(val) ((long)temp_lut[val] * 100)
/* for 10-bit temperature readings */
static inline long TEMP_FROM_REG10(u16 val)
{
u16 eight_bits = val >> 2;
u16 two_bits = val & 3;
/* no interpolation for these */
if (two_bits == 0 || eight_bits == 255)
return TEMP_FROM_REG(eight_bits);
/* do some linear interpolation */
return (temp_lut[eight_bits] * (4 - two_bits) +
temp_lut[eight_bits + 1] * two_bits) * 25;
}
#define DIV_FROM_REG(val) (1 << (val))
#define DIV_TO_REG(val) ((val) == 8 ? 3 : (val) == 4 ? 2 : (val) == 1 ? 0 : 1)
/*
* For each registered chip, we need to keep some data in memory.
* The structure is dynamically allocated.
*/
struct via686a_data {
unsigned short addr;
const char *name;
struct device *hwmon_dev;
struct mutex update_lock;
bool valid; /* true if following fields are valid */
unsigned long last_updated; /* In jiffies */
u8 in[5]; /* Register value */
u8 in_max[5]; /* Register value */
u8 in_min[5]; /* Register value */
u8 fan[2]; /* Register value */
u8 fan_min[2]; /* Register value */
u16 temp[3]; /* Register value 10 bit */
u8 temp_over[3]; /* Register value */
u8 temp_hyst[3]; /* Register value */
u8 fan_div[2]; /* Register encoding, shifted right */
u16 alarms; /* Register encoding, combined */
};
static struct pci_dev *s_bridge; /* pointer to the (only) via686a */
static inline int via686a_read_value(struct via686a_data *data, u8 reg)
{
return inb_p(data->addr + reg);
}
static inline void via686a_write_value(struct via686a_data *data, u8 reg,
u8 value)
{
outb_p(value, data->addr + reg);
}
static void via686a_update_fan_div(struct via686a_data *data)
{
int reg = via686a_read_value(data, VIA686A_REG_FANDIV);
data->fan_div[0] = (reg >> 4) & 0x03;
data->fan_div[1] = reg >> 6;
}
static struct via686a_data *via686a_update_device(struct device *dev)
{
struct via686a_data *data = dev_get_drvdata(dev);
int i;
mutex_lock(&data->update_lock);
if (time_after(jiffies, data->last_updated + HZ + HZ / 2)
|| !data->valid) {
for (i = 0; i <= 4; i++) {
data->in[i] =
via686a_read_value(data, VIA686A_REG_IN(i));
data->in_min[i] = via686a_read_value(data,
VIA686A_REG_IN_MIN
(i));
data->in_max[i] =
via686a_read_value(data, VIA686A_REG_IN_MAX(i));
}
for (i = 1; i <= 2; i++) {
data->fan[i - 1] =
via686a_read_value(data, VIA686A_REG_FAN(i));
data->fan_min[i - 1] = via686a_read_value(data,
VIA686A_REG_FAN_MIN(i));
}
for (i = 0; i <= 2; i++) {
data->temp[i] = via686a_read_value(data,
VIA686A_REG_TEMP[i]) << 2;
data->temp_over[i] =
via686a_read_value(data,
VIA686A_REG_TEMP_OVER[i]);
data->temp_hyst[i] =
via686a_read_value(data,
VIA686A_REG_TEMP_HYST[i]);
}
/*
* add in lower 2 bits
* temp1 uses bits 7-6 of VIA686A_REG_TEMP_LOW1
* temp2 uses bits 5-4 of VIA686A_REG_TEMP_LOW23
* temp3 uses bits 7-6 of VIA686A_REG_TEMP_LOW23
*/
data->temp[0] |= (via686a_read_value(data,
VIA686A_REG_TEMP_LOW1)
& 0xc0) >> 6;
data->temp[1] |=
(via686a_read_value(data, VIA686A_REG_TEMP_LOW23) &
0x30) >> 4;
data->temp[2] |=
(via686a_read_value(data, VIA686A_REG_TEMP_LOW23) &
0xc0) >> 6;
via686a_update_fan_div(data);
data->alarms =
via686a_read_value(data,
VIA686A_REG_ALARM1) |
(via686a_read_value(data, VIA686A_REG_ALARM2) << 8);
data->last_updated = jiffies;
data->valid = true;
}
mutex_unlock(&data->update_lock);
return data;
}
/* following are the sysfs callback functions */
/* 7 voltage sensors */
static ssize_t in_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", IN_FROM_REG(data->in[nr], nr));
}
static ssize_t in_min_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", IN_FROM_REG(data->in_min[nr], nr));
}
static ssize_t in_max_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", IN_FROM_REG(data->in_max[nr], nr));
}
static ssize_t in_min_store(struct device *dev, struct device_attribute *da,
const char *buf, size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
data->in_min[nr] = IN_TO_REG(val, nr);
via686a_write_value(data, VIA686A_REG_IN_MIN(nr),
data->in_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t in_max_store(struct device *dev, struct device_attribute *da,
const char *buf, size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
data->in_max[nr] = IN_TO_REG(val, nr);
via686a_write_value(data, VIA686A_REG_IN_MAX(nr),
data->in_max[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static SENSOR_DEVICE_ATTR_RO(in0_input, in, 0);
static SENSOR_DEVICE_ATTR_RW(in0_min, in_min, 0);
static SENSOR_DEVICE_ATTR_RW(in0_max, in_max, 0);
static SENSOR_DEVICE_ATTR_RO(in1_input, in, 1);
static SENSOR_DEVICE_ATTR_RW(in1_min, in_min, 1);
static SENSOR_DEVICE_ATTR_RW(in1_max, in_max, 1);
static SENSOR_DEVICE_ATTR_RO(in2_input, in, 2);
static SENSOR_DEVICE_ATTR_RW(in2_min, in_min, 2);
static SENSOR_DEVICE_ATTR_RW(in2_max, in_max, 2);
static SENSOR_DEVICE_ATTR_RO(in3_input, in, 3);
static SENSOR_DEVICE_ATTR_RW(in3_min, in_min, 3);
static SENSOR_DEVICE_ATTR_RW(in3_max, in_max, 3);
static SENSOR_DEVICE_ATTR_RO(in4_input, in, 4);
static SENSOR_DEVICE_ATTR_RW(in4_min, in_min, 4);
static SENSOR_DEVICE_ATTR_RW(in4_max, in_max, 4);
/* 3 temperatures */
static ssize_t temp_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", TEMP_FROM_REG10(data->temp[nr]));
}
static ssize_t temp_over_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", TEMP_FROM_REG(data->temp_over[nr]));
}
static ssize_t temp_hyst_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%ld\n", TEMP_FROM_REG(data->temp_hyst[nr]));
}
static ssize_t temp_over_store(struct device *dev,
struct device_attribute *da, const char *buf,
size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
data->temp_over[nr] = TEMP_TO_REG(val);
via686a_write_value(data, VIA686A_REG_TEMP_OVER[nr],
data->temp_over[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t temp_hyst_store(struct device *dev,
struct device_attribute *da, const char *buf,
size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
long val;
int err;
err = kstrtol(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
data->temp_hyst[nr] = TEMP_TO_REG(val);
via686a_write_value(data, VIA686A_REG_TEMP_HYST[nr],
data->temp_hyst[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static SENSOR_DEVICE_ATTR_RO(temp1_input, temp, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_max, temp_over, 0);
static SENSOR_DEVICE_ATTR_RW(temp1_max_hyst, temp_hyst, 0);
static SENSOR_DEVICE_ATTR_RO(temp2_input, temp, 1);
static SENSOR_DEVICE_ATTR_RW(temp2_max, temp_over, 1);
static SENSOR_DEVICE_ATTR_RW(temp2_max_hyst, temp_hyst, 1);
static SENSOR_DEVICE_ATTR_RO(temp3_input, temp, 2);
static SENSOR_DEVICE_ATTR_RW(temp3_max, temp_over, 2);
static SENSOR_DEVICE_ATTR_RW(temp3_max_hyst, temp_hyst, 2);
/* 2 Fans */
static ssize_t fan_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[nr],
DIV_FROM_REG(data->fan_div[nr])));
}
static ssize_t fan_min_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%d\n",
FAN_FROM_REG(data->fan_min[nr],
DIV_FROM_REG(data->fan_div[nr])));
}
static ssize_t fan_div_show(struct device *dev, struct device_attribute *da,
char *buf) {
struct via686a_data *data = via686a_update_device(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
return sprintf(buf, "%d\n", DIV_FROM_REG(data->fan_div[nr]));
}
static ssize_t fan_min_store(struct device *dev, struct device_attribute *da,
const char *buf, size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
via686a_write_value(data, VIA686A_REG_FAN_MIN(nr+1), data->fan_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t fan_div_store(struct device *dev, struct device_attribute *da,
const char *buf, size_t count) {
struct via686a_data *data = dev_get_drvdata(dev);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int nr = attr->index;
int old;
unsigned long val;
int err;
err = kstrtoul(buf, 10, &val);
if (err)
return err;
mutex_lock(&data->update_lock);
old = via686a_read_value(data, VIA686A_REG_FANDIV);
data->fan_div[nr] = DIV_TO_REG(val);
old = (old & 0x0f) | (data->fan_div[1] << 6) | (data->fan_div[0] << 4);
via686a_write_value(data, VIA686A_REG_FANDIV, old);
mutex_unlock(&data->update_lock);
return count;
}
static SENSOR_DEVICE_ATTR_RO(fan1_input, fan, 0);
static SENSOR_DEVICE_ATTR_RW(fan1_min, fan_min, 0);
static SENSOR_DEVICE_ATTR_RW(fan1_div, fan_div, 0);
static SENSOR_DEVICE_ATTR_RO(fan2_input, fan, 1);
static SENSOR_DEVICE_ATTR_RW(fan2_min, fan_min, 1);
static SENSOR_DEVICE_ATTR_RW(fan2_div, fan_div, 1);
/* Alarms */
static ssize_t alarms_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct via686a_data *data = via686a_update_device(dev);
return sprintf(buf, "%u\n", data->alarms);
}
static DEVICE_ATTR_RO(alarms);
static ssize_t alarm_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
int bitnr = to_sensor_dev_attr(attr)->index;
struct via686a_data *data = via686a_update_device(dev);
return sprintf(buf, "%u\n", (data->alarms >> bitnr) & 1);
}
static SENSOR_DEVICE_ATTR_RO(in0_alarm, alarm, 0);
static SENSOR_DEVICE_ATTR_RO(in1_alarm, alarm, 1);
static SENSOR_DEVICE_ATTR_RO(in2_alarm, alarm, 2);
static SENSOR_DEVICE_ATTR_RO(in3_alarm, alarm, 3);
static SENSOR_DEVICE_ATTR_RO(in4_alarm, alarm, 8);
static SENSOR_DEVICE_ATTR_RO(temp1_alarm, alarm, 4);
static SENSOR_DEVICE_ATTR_RO(temp2_alarm, alarm, 11);
static SENSOR_DEVICE_ATTR_RO(temp3_alarm, alarm, 15);
static SENSOR_DEVICE_ATTR_RO(fan1_alarm, alarm, 6);
static SENSOR_DEVICE_ATTR_RO(fan2_alarm, alarm, 7);
static ssize_t name_show(struct device *dev, struct device_attribute
*devattr, char *buf)
{
struct via686a_data *data = dev_get_drvdata(dev);
return sprintf(buf, "%s\n", data->name);
}
static DEVICE_ATTR_RO(name);
static struct attribute *via686a_attributes[] = {
&sensor_dev_attr_in0_input.dev_attr.attr,
&sensor_dev_attr_in1_input.dev_attr.attr,
&sensor_dev_attr_in2_input.dev_attr.attr,
&sensor_dev_attr_in3_input.dev_attr.attr,
&sensor_dev_attr_in4_input.dev_attr.attr,
&sensor_dev_attr_in0_min.dev_attr.attr,
&sensor_dev_attr_in1_min.dev_attr.attr,
&sensor_dev_attr_in2_min.dev_attr.attr,
&sensor_dev_attr_in3_min.dev_attr.attr,
&sensor_dev_attr_in4_min.dev_attr.attr,
&sensor_dev_attr_in0_max.dev_attr.attr,
&sensor_dev_attr_in1_max.dev_attr.attr,
&sensor_dev_attr_in2_max.dev_attr.attr,
&sensor_dev_attr_in3_max.dev_attr.attr,
&sensor_dev_attr_in4_max.dev_attr.attr,
&sensor_dev_attr_in0_alarm.dev_attr.attr,
&sensor_dev_attr_in1_alarm.dev_attr.attr,
&sensor_dev_attr_in2_alarm.dev_attr.attr,
&sensor_dev_attr_in3_alarm.dev_attr.attr,
&sensor_dev_attr_in4_alarm.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_temp3_input.dev_attr.attr,
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp2_max.dev_attr.attr,
&sensor_dev_attr_temp3_max.dev_attr.attr,
&sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
&sensor_dev_attr_temp1_alarm.dev_attr.attr,
&sensor_dev_attr_temp2_alarm.dev_attr.attr,
&sensor_dev_attr_temp3_alarm.dev_attr.attr,
&sensor_dev_attr_fan1_input.dev_attr.attr,
&sensor_dev_attr_fan2_input.dev_attr.attr,
&sensor_dev_attr_fan1_min.dev_attr.attr,
&sensor_dev_attr_fan2_min.dev_attr.attr,
&sensor_dev_attr_fan1_div.dev_attr.attr,
&sensor_dev_attr_fan2_div.dev_attr.attr,
&sensor_dev_attr_fan1_alarm.dev_attr.attr,
&sensor_dev_attr_fan2_alarm.dev_attr.attr,
&dev_attr_alarms.attr,
&dev_attr_name.attr,
NULL
};
static const struct attribute_group via686a_group = {
.attrs = via686a_attributes,
};
static void via686a_init_device(struct via686a_data *data)
{
u8 reg;
/* Start monitoring */
reg = via686a_read_value(data, VIA686A_REG_CONFIG);
via686a_write_value(data, VIA686A_REG_CONFIG, (reg | 0x01) & 0x7F);
/* Configure temp interrupt mode for continuous-interrupt operation */
reg = via686a_read_value(data, VIA686A_REG_TEMP_MODE);
via686a_write_value(data, VIA686A_REG_TEMP_MODE,
(reg & ~VIA686A_TEMP_MODE_MASK)
| VIA686A_TEMP_MODE_CONTINUOUS);
/* Pre-read fan clock divisor values */
via686a_update_fan_div(data);
}
/* This is called when the module is loaded */
static int via686a_probe(struct platform_device *pdev)
{
struct via686a_data *data;
struct resource *res;
int err;
/* Reserve the ISA region */
res = platform_get_resource(pdev, IORESOURCE_IO, 0);
if (!devm_request_region(&pdev->dev, res->start, VIA686A_EXTENT,
DRIVER_NAME)) {
dev_err(&pdev->dev, "Region 0x%lx-0x%lx already in use!\n",
(unsigned long)res->start, (unsigned long)res->end);
return -ENODEV;
}
data = devm_kzalloc(&pdev->dev, sizeof(struct via686a_data),
GFP_KERNEL);
if (!data)
return -ENOMEM;
platform_set_drvdata(pdev, data);
data->addr = res->start;
data->name = DRIVER_NAME;
mutex_init(&data->update_lock);
/* Initialize the VIA686A chip */
via686a_init_device(data);
/* Register sysfs hooks */
err = sysfs_create_group(&pdev->dev.kobj, &via686a_group);
if (err)
return err;
data->hwmon_dev = hwmon_device_register(&pdev->dev);
if (IS_ERR(data->hwmon_dev)) {
err = PTR_ERR(data->hwmon_dev);
goto exit_remove_files;
}
return 0;
exit_remove_files:
sysfs_remove_group(&pdev->dev.kobj, &via686a_group);
return err;
}
static void via686a_remove(struct platform_device *pdev)
{
struct via686a_data *data = platform_get_drvdata(pdev);
hwmon_device_unregister(data->hwmon_dev);
sysfs_remove_group(&pdev->dev.kobj, &via686a_group);
}
static struct platform_driver via686a_driver = {
.driver = {
.name = DRIVER_NAME,
},
.probe = via686a_probe,
.remove_new = via686a_remove,
};
static const struct pci_device_id via686a_pci_ids[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4) },
{ }
};
MODULE_DEVICE_TABLE(pci, via686a_pci_ids);
static int via686a_device_add(unsigned short address)
{
struct resource res = {
.start = address,
.end = address + VIA686A_EXTENT - 1,
.name = DRIVER_NAME,
.flags = IORESOURCE_IO,
};
int err;
err = acpi_check_resource_conflict(&res);
if (err)
goto exit;
pdev = platform_device_alloc(DRIVER_NAME, address);
if (!pdev) {
err = -ENOMEM;
pr_err("Device allocation failed\n");
goto exit;
}
err = platform_device_add_resources(pdev, &res, 1);
if (err) {
pr_err("Device resource addition failed (%d)\n", err);
goto exit_device_put;
}
err = platform_device_add(pdev);
if (err) {
pr_err("Device addition failed (%d)\n", err);
goto exit_device_put;
}
return 0;
exit_device_put:
platform_device_put(pdev);
exit:
return err;
}
static int via686a_pci_probe(struct pci_dev *dev,
const struct pci_device_id *id)
{
u16 address, val;
int ret;
if (force_addr) {
address = force_addr & ~(VIA686A_EXTENT - 1);
dev_warn(&dev->dev, "Forcing ISA address 0x%x\n", address);
ret = pci_write_config_word(dev, VIA686A_BASE_REG, address | 1);
if (ret != PCIBIOS_SUCCESSFUL)
return -ENODEV;
}
ret = pci_read_config_word(dev, VIA686A_BASE_REG, &val);
if (ret != PCIBIOS_SUCCESSFUL)
return -ENODEV;
address = val & ~(VIA686A_EXTENT - 1);
if (address == 0) {
dev_err(&dev->dev,
"base address not set - upgrade BIOS or use force_addr=0xaddr\n");
return -ENODEV;
}
ret = pci_read_config_word(dev, VIA686A_ENABLE_REG, &val);
if (ret != PCIBIOS_SUCCESSFUL)
return -ENODEV;
if (!(val & 0x0001)) {
if (!force_addr) {
dev_warn(&dev->dev,
"Sensors disabled, enable with force_addr=0x%x\n",
address);
return -ENODEV;
}
dev_warn(&dev->dev, "Enabling sensors\n");
ret = pci_write_config_word(dev, VIA686A_ENABLE_REG, val | 0x1);
if (ret != PCIBIOS_SUCCESSFUL)
return -ENODEV;
}
if (platform_driver_register(&via686a_driver))
goto exit;
/* Sets global pdev as a side effect */
if (via686a_device_add(address))
goto exit_unregister;
/*
* Always return failure here. This is to allow other drivers to bind
* to this pci device. We don't really want to have control over the
* pci device, we only wanted to read as few register values from it.
*/
s_bridge = pci_dev_get(dev);
return -ENODEV;
exit_unregister:
platform_driver_unregister(&via686a_driver);
exit:
return -ENODEV;
}
static struct pci_driver via686a_pci_driver = {
.name = DRIVER_NAME,
.id_table = via686a_pci_ids,
.probe = via686a_pci_probe,
};
static int __init sm_via686a_init(void)
{
return pci_register_driver(&via686a_pci_driver);
}
static void __exit sm_via686a_exit(void)
{
pci_unregister_driver(&via686a_pci_driver);
if (s_bridge != NULL) {
platform_device_unregister(pdev);
platform_driver_unregister(&via686a_driver);
pci_dev_put(s_bridge);
s_bridge = NULL;
}
}
MODULE_AUTHOR("Kyösti Mälkki <[email protected]>, "
"Mark Studebaker <[email protected]> "
"and Bob Dougherty <[email protected]>");
MODULE_DESCRIPTION("VIA 686A Sensor device");
MODULE_LICENSE("GPL");
module_init(sm_via686a_init);
module_exit(sm_via686a_exit);
Codebase Browser
linux